SNE FAP Series User manual

FAP Series Operating Directions
New Environmental International
1
SNE®FAP Series
HVAC Air Purification System
Operations Manual
Thank you for purchasing the FAP Series HVAC Air Purification Product.

FAP Series Operating Directions
New Environmental International
2
We are confident this system will provide you a fresh, clean, odor free and
healthy air environment.
NOTE:
Please take time to read the attached Manual and should be adhered to while
operating this system.
The FAP by SNE®Systems are designed to eliminate sick building syndrome risks by
killing and reducing bacteria, virus, odors and VOC, through MCITM Multi Catalytic
Ionization Technology. The FAP are easily mounted into HVAC Air Conditioning air
ducts (Included the AHU & PAU systems) Where most sick buildingproblems exist.
When the air conditioning unit is in operation, the FAP creates the Multi Catalytic
Oxidation Process to eliminate the air pollutant.
FAP HVAC Air Purification System:
Remarks:
1, FAP is application to the HVAC System, Included AHU (Air Handling Unit) & PAU
( Packaged Air Unit ) etc.
2, FAP all is dual probes.
3, When selecting model over the FAP series, You can be select many FAP models to installing
parallel and operation, It can be to promote the purification effects.
4, Option:
No
.
Model
UV Length
HVAC Air Blower
Volume
Approx.
H=3m
Consumption
AC/100-220V
/50-60Hz
1
FAP-100DF
2 X 212 mm
1,500-9,000 m3/h
60-100m2
10W X 2
2
FAP-300DF
2 X 287 mm
9,000-1,5000 m3/h
100-300m2
12W X 2
3
FAP-500DF
2 X 356 mm
1,5000-2,5000 m3/h
300-500m2
15W X 2
4
FAP-600DF
2 X 436 mm
2,5000-3,5000 m3/h
500-700m2
20W X 2
5
FAP-700DF
2 X 540 mm
3,5000-45,000 m3/h
700-900m2
25W X 2

FAP Series Operating Directions
New Environmental International
3
---Pure UV System: FAP-100-700DV.
---Auto: Programmable Timer or Auto/Man Control Box.
---Remote control interface.
Figure-1 FAP Size Diagrams
L: red N: green（blue）Ground: = yellow
25 cm
4.8cm
212-540 mm
31 cm
4cm

CAP Series Operating Directions
New Environmental International
Figure-2 FAP Panel Diagrams
Figure-3 FAP Install Diagrams
SNE
®
FAP Series
Fan Duct HVAC Air Purification System
FAN
FAP-300DF
LAMP
POWER

CAP Series Operating Directions
New Environmental International
SNE ® MCITM Technology has been Tested and Certified by the
Figure-4 FAP Size Diagrams
Remarks:
Probe Ø=4.8cm
Install can >5.5cm
Install Ø0=0.5cm
1cm
Install Ø2=0.4cm
Install Ø1=0.4cm
14 cm
9 cm
31 cm
8 cm
23 cm
A
B
A
B
1 cm
C
C

CAP Series Operating Directions
New Environmental International
A: Fixed and Connected UV probe with the electrical box fitting.
B: UV Lamp.
C: Fixed and Connected UV probe with the “A “fitting.
D: Probe= B + C.
Installation:
1, Power Supply:
---AC/100-250V/50-60Hz.
---FAP power must be connected to the AHU or PAU air blower power, The AC air blower
operating, FAP open, AC air blower close, FAP close, too.
---Always leave the air blower, You can be add a switch in the FAP power, or add a Timer.
---Electrical connections should only be made licensed HVAC or Electrical Contractor.
WARNING!!!
Never look directly the UV light tube. It may cause blindness.
2, Install to the HVAC System.
---Take to dismantle of the UV probe’s protecting membrane.
---Installation to the main Return Air Duct end, but the Export Air duct start point, that right
too
(Figure-3).
---The UV Probe Ø=4.8cm, Installing hole can be cut >5.5cm (Figure-4).
---Use 4 X 0.5cm screws to fix the HVAC return air duct. (Figure-4, Install Ø0=0.6cm)
--- The FAP Panel had FAN <-------- display, It to indicate installing FAP must be note
the Air Blower direction (Figure-2).
--- Detail. Please look the FAP & CAP Installation DVD or Installation Figure.
UV Probe Replacement:

CAP Series Operating Directions
New Environmental International
1, After 2-3 years of normal use, or 1.5 years of continuous use, the UV Probe will need
replaced.
2, “Off”the power or unplug from the power supply.
3, Unscrew the 2 units X “A”4 units Ø1 =0.4 cm ( Figure-4, A: Fixed and Connected
probe with the electrical box fitting).
4, Unscrew the 2 units X “C”4 units Ø2=0.4 cm ( Figure-4)
5, Remove end connectors by gently pulling away from probe ends.
6, Replace with new probe, Please note: the FAP Panel had FAN <--------
display,
Its obverse side direction is “V”probe (white).
7, Re-assemble and check for the FAP.
Probe Number:
R-FAP-100Z/V (Z & V each one / Set)---------------------FAP-100DF
R-FAP-300Z/V (Z & V each one / Set)---------------------FAP-300DF
R-FAP-500Z/V (Z & V each one / Set)---------------------FAP-500DF
R-FAP-600Z/V (Z & V each one / Set)---------------------FAP-600DF
R-FAP-700Z/V (Z & V each one / Set)---------------------FAP-700DF
9 cm