Sharp FP-JM30E User manual

AIR PURIFIER
WITH MOSQUITO CATCHER
OPERATION MANUAL
R
FP-JM30E
FP-JM30L
FP-JM30P
FP-JM30V
ENGLISHMALAYSIA
PEMBERSIH UDARA
dengan fungsi Pemerangkap
Nyamuk
BUKU PANDUAN OPERASI
HƯỚNG DẪN SỬ DỤNG MÁY
LỌC KHÔNG KHÍ CÓ CÔNG
CỤ BẮT MUỖI
TIẾNG VIỆT
“Plasmacluster” and “Device of a cluster of grapes” are
registered trademarks of Sharp Corporation in Japan,
Philippines and elsewhere.
*The number in this technology mark indicates an approximate
number of ions supplied into air of 1 cm
3
, which is measured
around the center of a room applicable oor area (at 1.2 m
height above the oor) when the product is placed close to a
wall at the MED mode setting.
捕蚊空气净化器
操作手册
中文
FP-JM30ELPV_EN_MS_VI_ZH.indb 1 2019/04/08 11:35:47

The air purier draws in room air through the air intake, circulates it through a Pre-
Filter and a HEPA Filter inside the main unit, and then discharges it through the air
outlet. The HEPA Filter can remove 99.97% of dust particles as small as 0.3 microns
that pass through the lter.
Some odors absorbed by the lter will break down over time, causing additional
odors. Depending on usage conditions, and especially if the main unit is used in
environments signicantly more severe than a normal household, these odors may
become noticeable sooner than expected. If these odors persist, replace the lter.
(Page 12)
Please read before operating your new Air Purier
FEATURES
Air Purifier with Mosquito Catcher protects your family’s health by catching
mosquitoes and cleaning the air by plasmacluster technology.
Catches mosquitoes with Insecticide-free material.
5 e󰀨ective steps*1 based on ndings about mosquito habits, and by using air purier function.
2
1
345
1
2
3
4
5
※Mosquito catcher mode may not catch all the mosquitoes in the room.
*1: In collaboration with Institute for Medical Research, Malaysia.
UV Light attracts mosquitoes Enticing ‘Black’ color
Ideal entrance design Powerful airow and suction Strong Glue Sheet
FP-JM30ELPV_EN_MS_VI_ZH.indb 2 2019/04/08 11:35:47

EN-1
ENGLISH
ENGLISH
Thank you for purchasing the SHARP Air Purier.
Please read this manual carefully.
Before using this product, be sure to read the
section: “Important Safety Instructions.”
After reading this manual, keep it in a convenient
location for future reference.
For your reference, we recommend to keep this
manual in the place where you can read at any
time.
IMPORTANT SAFETY
INSTRUCTIONS ...................................EN-2
PART NAMES ......................................EN-4
FILTER AND GLUE SHEET
INSTALLATION .................................... EN-6
OPERATION ........................................EN-8
CARE AND MAINTENANCE .............EN-10
REPLACEMENT GUIDELINES ......... EN-12
TROUBLESHOOTING .......................EN-14
SPECIFICATIONS ..............................EN-15
CONTENTS
High density Plasmacluster 7000
Plasmacluster treats the air similar to the way
nature cleans the environment by emitting a bal-
ance of positive and negative ions.
Convenient HAZE operation when
the HAZE is present
HAZE mode enables fast removal of HAZE with
high air volume.
Quiet operation while capture the
mosquitoes at the time of sleep
When you switch to SLEEP mode, it operates
quietly with the Plasmacluster Ion and UV Indi-
cator Lights light o󰀨 and the UV Light less bright,
while mosquito catcher function is still on.
Filtration System
Traps Dust*2
Pre-Filter traps dust and other large airborne par-
ticles.
Reduces Pollen & Mold*2
HEPA Filter traps 99.97% of particles as small as
0.3 microns.
*2 When air is drawn through the lter system.
FP-JM30ELPV_EN_MS_VI_ZH.indb 1 2019/04/08 11:35:48

EN-2
IMPORTANT SAFETY INSTRUCTIONS
Always follow basic safety precautions
when using electrical appliances,
including the following:
WARNING – Always observe the
following to reduce the risk of electrical
shock, re, or injury:
• Read all instructions before using the
main unit.
• Use only a 220-240 volt outlet.
• This appliance is not intended for
use by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction concerning use of the
appliance by a person responsible
for their safety.
Children should be supervised to
ensure they do not play with the
appliance.
• If the power cord is damaged, it must
be replaced by the manufacturer, its
service agent, a Sharp authorized
Service Center or similarly qualied
persons in order to avoid a hazard.
Contact the nearest Service Center
for any problems, adjustments, or
repairs.
• Be sure to remove the power plug,
before performing maintenance,
when removing and attaching and
replacing the lter and when not
using for a long time. Failure to do
so can cause a short circuit resulting
in electrical shock or re.
• Do not use the main unit if the power
cord or plug is damaged or if the
connection to the wall outlet is loose.
• Periodically remove dust from the plug.
• Do not insert ngers or foreign objects
into the air intake or air outlet.
• When removing the power plug, always
hold the plug and never pull on the
cord.
Failure to do so can cause a short
circuit resulting in electrical shock or
re.
• Be careful not to damage the power
cord, it may cause electric shock,
excess heat or res.
• Do not remove the plug when your hands
are wet.
• Do not place the main unit near or on
hot objects, such as stoves or heaters,
or where it may come into contact with
steam.
• Do not operate the main unit in rooms
where aerosol insecticides are present.
Do not operate the main unit in rooms
where there is oily residue, incense,
sparks from lit cigarettes, or chemical
fumes in the air. Do not operate the main
unit in places where it may get wet, such
as a bathroom.
• Be cautious when cleaning the main unit.
Strong corrosive cleansers can damage
the exterior.
• Do not expose the main unit to water.
Doing so can cause a short circuit or
electrical shock.
NOTE – What to do if the main unit
interferes with radio or TV reception
If the air purier interferes with radio or
television reception, try one or more of the
following measures:
• Adjust or reposition the receiving antenna.
• Increase the distance between the main
unit and the radio or TV.
• Connect the equipment into an outlet on a
circuit di󰀨erent from that of the radio or TV
receiver.
• Consult the dealer or a qualied radio or
TV technician.
FP-JM30ELPV_EN_MS_VI_ZH.indb 2 2019/04/08 11:35:48

EN-3
ENGLISH
CAUTIONS CONCERNING
OPERATION
• Do not block the air intake or air outlet.
• Always operate the main unit in an
upright position.
• Do not move the main unit when it is in
operation.
• When moving the main unit, use the
handles on both sides.
• If the main unit is on easily damaged
ooring, an uneven surface, or thick-piled
carpet, lift it up when moving.
• Do not operate the main unit without the
lters properly installed.
• Do not wash and reuse the HEPA Filter.
Doing so will not improve lter
performance and can also cause electric
shock or operating malfunctions.
• Clean the exterior with a soft cloth only.
Do not use volatile uids or detergents.
The main unit surface may be damaged
or cracked with Benzine, paint thinner or
polishing powder. In addition, the sensors
may malfunction as a result.
• Do not scrub the Pre-Filter hard during its
maintenance.
• Do not look directly into the UV Light.
UV Light meet the standards of IEC
(62471).
CAUTIONS CONCERNING
GLUE SHEET
• Handle the Glue Sheet with care. Avoid
children or pet from touching the sticky
surface.
• If the glue material adheres to hands or
clothing, wash them quickly and carefully
with soap and water after removing the
material by using cooking oil.
• Dust and dirt collecting on the sheet may
reduce the e󰀨ectiveness of Glue Sheet.
• If no mosquitoes are collected on the
sheet, try changing the location of the
main unit.
• When disposal, dispose it according to
the local disposal laws and regulations.
• This is a completely safe adhesive type
product. No toxic ingredients.
INSTALLATION GUIDELINES
• Avoid locations where the sensors are
exposed to direct wind.
Doing so can cause the main unit to
malfunction.
• Avoid locations where furniture, fabrics,
or other objects can come in contact with
the main unit and interfere with the intake
and outtake of air.
• Avoid locations where the main unit
is exposed to condensation or drastic
changes in temperature. Appropriate
room temperature is between 0 – 35 ºC.
• Place the main unit on a level and stable
surface with su󰀩cient air circulation.
When placed on heavy carpet, the main
unit may vibrate slightly.
• Avoid locations that generate grease or
oily smoke.
Doing so can cause the main unit exterior
to crack and the sensors to malfunction.
• The dust collecting ability of the main
unit is e󰀨ective even when the main unit
is as close to 3 cm from the wall,the
surrounding walls and oor may get dirty.
Please place the main unit at a distance
from the wall.
The wall directly behind the air outlet may
become dirty over time. When using the
main unit for an extended period of time
at the same location, periodically clean
the walls adjacent to it.
FILTER GUIDELINES
• Follow the instructions in this manual for
proper lter care and maintenance.
FP-JM30ELPV_EN_MS_VI_ZH.indb 3 2019/04/08 11:35:48

EN-4
PART NAMES
2
FRONT
1
1Air Outlet
2Main Unit
3MODE Button, Light (green)
(Press 3 sec.) Plasmacluster Ion ON/OFF Button
4OFF TIMER Button, Light (green)
(Press 3 sec.) Filter RESET Button
5REPLACE FILTER Light (orange)
6Plasmacluster Ion Indicator Light (blue)
7HAZE Button, Light (green)
(Press 3 sec.) LIGHT ON/OFF Button
8POWER ON/OFF Button
9MOSQUITO CATCHER Button
(Press 3 sec.) SHEET RESET Button
10 UV Indicator Light (blue)
8
5
3
9
4
10
6
7
FP-JM30ELPV_EN_MS_VI_ZH.indb 4 2019/04/08 11:35:48

EN-5
ENGLISH
BACK
10
1UV Light 8Upper Hook
2HEPA Filter 9Bottom Hook
3Pre-Filter 10 Power Cord
4Pre-Filter Tabs 11 Plug
(Shape of plug depends on country.)
5Catch Panel
6Handle 12 Air Inlet
7Magnet 13 Glue Sheet
INCLUDED
• Glue Sheet : 2 pieces
11
13
4
5
3
2
9
8
7
(INSIDE)
Hold this Handle
when lifting the
main unit.
6
1
12
FP-JM30ELPV_EN_MS_VI_ZH.indb 5 2019/04/08 11:35:48

EN-6
FILTER AND GLUE SHEET INSTALLATION
To maintain the quality of the lter and Glue Sheet, it is installed in the main unit and packed in plas-
tic bag. Be sure to remove the lter and Glue Sheet from the plastic bag before using the main unit.
1
Remove the Catch Panel from
underpart.
2
Hold the tabs of Pre-Filter and
remove it.
3
Remove the lter.
4
Remove the lter from
the plastic bag.
5Hold upper part of HEPA Filter
and set it.
6Hold tab of Pre-Filter, and install
it.
1 2
1 2
21
HEPA Filter
Tag
3
2
1
FP-JM30ELPV_EN_MS_VI_ZH.indb 6 2019/04/08 11:35:49

EN-7
ENGLISH
Be sure to remove the power plug from the wall outlet.
7
Remove the Glue Sheet from the
plastic bag.
・ Keep the additional Glue Sheet
away from direct sunlight and
lay it at with glue side face up.
8
①Hang the Glue Sheet on Upper
hook of the inner side of the
Catch Panel.
②Insert it into Bottom hook.
9
Remove protective film slowly
from the corner of Glue Sheet.
・Dispose protective lm as
burnable rubbish.
・Make sure that its bottom part is
properly inserted to the Bottom
hook.
10
Attach Catch Panel from upper
part.
Be careful not to stick the Glue
Sheet to hair or clothes.
2
1
2
1
Click
FP-JM30ELPV_EN_MS_VI_ZH.indb 7 2019/04/08 11:35:49

EN-8
OPERATION
MED MAX SLEEP
The main unit operates at HIGH fan speed for 60 minutes and then alternates between Low and High
level for 20 minutes each.
START / STOP
START
• Unless the power cord has been unplugged,
the operation starts in the previous mode it
was operated in.
STOP
HAZE
10 minutes: Max High fan level
50 minutes: High fan level
20 minutes: Low fan level
20 minutes: High fan level
• The Plasmacluster Ion can not be turned “OFF”.
• It is possible to switch this mode to another while operating.
However, the HAZE mode will not function after switching
mode.
NOTE
FAN SPEED
SLEEP
• The main unit will operate very quietly with low fan
speed. Plasmacluster Ion Indicator Light and UV
Indicator Light go o󰀨 and the UV Light becomes dark
automatically. Even though Plasmacluster Ion Indicator
Light is o󰀨, Plasmacluster Ion is dispersed into air
unless Plasmacluster Ion is turned o󰀨 by .
NOTE
OFF TIMER
4h ● 8h ● CANCEL
Select the time turning o󰀨 the main unit during operation. The main unit automatically stops once
the selected time is reached.
FP-JM30ELPV_EN_MS_VI_ZH.indb 8 2019/04/08 11:35:50

EN-9
ENGLISH
MOSQUITO CATCHER
Use this function when there is concern about mosquitoes.
NOTE
UV Light ON UV Light OFF
• When UV Indicator Light is ashing, please replace the Glue Sheet with a new one.
• Select MAX mode to catch mosquito more e󰀨ectively.
The higher the air volume is, the easier it is to capture a mosquito.
• If Catch Panel comes o󰀨, UV Indicator Light and UV Light are turned o󰀨 automatically.
Please check the Catch Panel is properly attached.
• We recommend you to keep this air purier working for 24 hours to maximize its function except
for exchanging lter and Glue Sheet.
Light Control
Plasmacluster Ion ON/OFF
You can set the Indicator Lights to OFF when the Indicator Lights are bright.
ON
more 3 sec. more 3 sec.
OFF
• When set to “OFF”, UV Indicator
Light and Plasmacluster Ion
Indicator Light turn o󰀨 and the UV
Light becomes dark.
After starting operation, they light
dark for 8 seconds and then turn
o󰀨.
NOTE
When Plasmacluster Ion is ON, the Plasmacluster Ion Indicator Light will turn on. (blue)
ON OFF
more 3 sec. more 3 sec.
FP-JM30ELPV_EN_MS_VI_ZH.indb 9 2019/04/08 11:35:51

EN-10
CARE AND MAINTENANCE
To maintain optimum performance of this air purier, please clean the main unit including the
lter periodically.
Be sure to disconnect the power cord from the wall outlet before performing any maintenance.
MAIN UNIT
Wipe with a dry, soft cloth
For stubborn stains or dirt, use a soft cloth dampened with warm water.
CAUTION
•Do not use volatile uids
Benzine, paint thinner, polishing powder, etc. , may damage the surface.
•Do not use detergents
Detergent ingredients may damage the main unit.
HEPA FILTER Gently remove dust from HEPA Filter with a vacuum
cleaner attachment or similar tool.
CAUTION
•Do not WASH in water and DRY in the sun.
•Apply the maintenance only on the side with the tag.
Do not clean the opposite side; otherwise, the lter
will be damaged.
The lter is fragile, be careful not to apply too much
pressure.
HEPA FILTER
When the smell is generated from
the Air Outlet
When the smell is hard to take
Do not WASH
PRE-FILTER Once a month
CATCH PANEL
Once in two months
Once in two months
MAIN UNIT
Tag
FP-JM30ELPV_EN_MS_VI_ZH.indb 10 2019/04/08 11:35:52

EN-11
ENGLISH
Gently remove dust from the Pre-Filter, using
a vacuum cleaner attachment or similar tool.
PRE-FILTER
Pre-Filter
CAUTION
Do not apply excessive pressure, when
scrubbing the Pre-Filter.
1. Add a small amount of kitchen detergent
to water and soak for about 10 minutes.
2. Rinse o󰀨 the kitchen detergent with clean
water.
3. Completely dry the lter in a well-ventilated
area.
NOTE How to clean hard to remove dirt
Pre-Filter
CATCH PANEL
Remove the Glue Sheet, gently remove dust
from the Catch Panel, using a vacuum cleaner
attachment or similar tool.
CAUTION
Do not apply excessive pressure, when
scrubbing the Catch Panel.
Be sure to remove the power plug from the wall outlet.
FP-JM30ELPV_EN_MS_VI_ZH.indb 11 2019/04/08 11:35:52

EN-12
REPLACEMENT GUIDELINES
Do not wash and reuse the lter
The lter life and replacement period are based
on the condition of smoking 5 cigarettes per day
and the dust collection power is reduced by half
compared with that of new lter.
Filter life varies depending on the room environ-
ment, usage, and location of the main unit.
We recommend to replace the filter more fre-
quently if the product is used in a condition signi-
cantly severer than normal household use.
Disposal of lter
Please dispose of the replaced lter according
to the local disposal laws and regulations.
Replacement timing
When REPLACE FILTER Light turn on.*
• Filter : Polypropylene
• Frame : Polyester
HEPA FILTER
Model : FZ-F30HFE
Replace the lter according to the instructions
provided with the replacement lter.
• Please consult your dealer for purchase of
replacement lter.
• Use only lter designed for this product.
After the exchange, insert the plug in socket and
press the POWER ON/OFF Button, and OFF TIMER
Button 3 seconds.
*
The REPLACE FILTER Light will turn on after
approximately 17,500 hours in SLEEP mode.
( 2 years × 24 hours = 17,500)
Filter life varies depend on the operation mode.
more 3 sec.
HEPA Filter
Glue Sheet
FP-JM30ELPV_EN_MS_VI_ZH.indb 12 2019/04/08 11:35:52

EN-13
ENGLISH
Replacement timing When UV Indicator Light is ashing.
Disposal of Glue Sheet
Please dispose of the replaced Glue Sheet according to the local disposal laws and regulations.
Glue Sheet materials :
•Glue: Acrylic copolymer
•Film: Paper
•Base Sheet: Polycarbonate
GLUE SHEET
Replace the Glue Sheet according to the operation manual included in the replacement Glue
Sheet.
Please discard the used Glue Sheet carefully.
Do not touch the
adhesive surface.
After the exchange, insert the plug in socket and press the POWER ON/OFF Button,
and MOSQUITO CATCHER Button 3 seconds.
• Please consult your dealer for purchase of replacement Glue Sheet.
• Use only Glue Sheet designed for this product.
Model : FZ-STS2M
UV Indicator Light will ash approximately 2 months (24 hours x 60 days) later when you insert
the plug in socket.
The replacement timing is about 2 months, but it may be early depending on the room environ-
ment.
Check the Glue Sheet sometimes.
more 3 sec.
ashing lighting
Be sure to remove the power plug from the wall outlet.
FP-JM30ELPV_EN_MS_VI_ZH.indb 13 2019/04/08 11:35:52

EN-14
TROUBLESHOOTING
SYMPTOM REMEDY (not a malfunction)
Dust and smoke are not removed. • Is lter still in the plastic bag? Please take it out.(Page 6)
• Clean or replace the lter if they appear to be heavily soiled.
(Page 10,12)
A clicking or ticking sound is heard
from the main unit.
• Clicking or ticking sounds may be audible when the main unit
is generating ions.
The discharged air has an odor. • Check to see if the lters are heavily soiled.
• Clean or replace the lters.
The Plasmacluster Ion Indicator
Light doesn’t light on.
• Check to see if the SLEEP mode is selected.
The Plasmacluster Ion Indicator Light is turned o󰀨 after the
SLEEP mode is selected.
• Check to see if the Plasmacluster Ion OFF is selected.
Press for 3 seconds to light On.(Page 9)
• Check to see if the Light Control OFF is selected. Press
for 3 seconds to light On.(Page 9)
UV Indicator Light and UV Light are
turned o󰀨. • If Catch Panel comes o󰀨 or is not properly set, UV Indicator Light and UV Light are automatically turned o󰀨 by Magnet
sensor.
Please conrm whether Catch Panel is properly attached.
UV Indicator Light is ashing • It’s replacement timing of Glue Sheet.
Please exchange to new Glue Sheet.
Then, press the MOSQUITO CATCHER Button for 3 seconds.
No mosquitoes are collected on the
Glue Sheet. • Aren’t windows or doors opened?
• Don’t you set up in the place where the wind blows such as air-
conditioner or fan?
Try to relocate the main unit.
When the adhesive remains on
clothes, skin, oor, etc. • Wipe with cooking oil, then wash with soap and water.
AUTO RESTART • Even when the plug is unplugged or the breaker is thrown
during the operation, the operation resumes at the previous
operation mode and settings if the power recovers.
Any two of MODE Lights are
ashing • UV Light has failed. Please call the service center approved by Sharp.
Before calling for service, please review the Troubleshooting chart below, since the problem may not be the
main unit malfunction.
ON(default) OFF
(with the main unit OFF) (with the main unit OFF)
If the , , Lights lights up
for 8 seconds, the setting is ‘ON’.
(simultaneously for
more than 3 sec.)
(simultaneously for
more than 3 sec.)
FP-JM30ELPV_EN_MS_VI_ZH.indb 14 2019/04/08 11:35:53

EN-15
ENGLISH
*1 Size of a room which is appropriate for operating the main unit at maximum fan speed.
• It indicates the space where a certain amount of dust particles can be removed in 30 minutes
(JEM1467).
*2 Size of a room in which approximately 7000 ions can be measured per cubic centimeter in the
center of the room (at a height of approximately 1.2 meters from the oor) when the product is
placed next to a wall and run at the MED operation position.
Standby Power In order to operate the electrical circuits while the power plug is inserted in the
wall outlet, this product consumes of standby power.
For energy saving, unplug the power cord when the main unit is not in use.
SPECIFICATIONS
Power supply 220-240V 50-60Hz
Fan Speed
Operation
Fan Speed Adjustment MAX MED SLEEP
Rated Power 53W 32W 19W
Fan Speed 180m3/hour 120m3/hour 78m3/hour
Standby Power 0.7W
Recommended Room Size ~23m2 *1
High density Plasmacluster ion recommended room size ~16m2 *2
Cord Length 2.0m
Dimensions 438mm(W)x253mm(D)x444mm(H)
Weight 4.7kg
FP-JM30ELPV_EN_MS_VI_ZH.indb 15 2019/04/08 11:35:53

Pembersih udara menyedut udara dalam bilik melalui salur masuk udara,
mengalirkannya melalui Prapenapis dan Penapis HEPA di dalam unit utama, kemudian
mengeluarkannya melalui salur keluar udara. Penapis HEPA boleh menyingkirkan
99.97% habuk sekecil 0.3 mikron yang dapat melalui penapis.
Sesetengah bau yang diserap oleh penapis, lama-kelamaan boleh terurai dan
menyebabkan bau semakin kuat. Bergantung pada keadaan penggunaan, dan
terutama sekali jika unit utama digunakan dalam persekitaran yang jauh lebih teruk
berbanding kediaman biasa, bau ini mungkin menjadi kuat lebih cepat daripada
jangkaan. Jika bau ini berlarutan, gantikan penapis. (halaman 12)
Sila baca sebelum mengendalikan Pembersih Udara baru anda
CIRI-CIRI
Pembersih Udara dengan Perangkap Nyamuk melindungi kesihatan keluarga
anda dengan memerangkap nyamuk dan membersihkan udara dengan teknologi
plasmacluster.
Memerangkap nyamuk dengan bahan bebas racun serangga.
5 langkah berkesan*1 berdasarkan hasil kajian tentang tabiat nyamuk dan menggunakan fungsi
pembersih udara.
2
1
345
1
2
3
4
5
※Mod Pemerangkap Nyamuk tidak semestinya akan memerangkap semua nyamuk di dalam bilik.
*1: Secara usaha sama dengan Institut Penyelidikan Perubatan Malaysia.
Cahaya UV menarik nyamuk Warna ‘Hitam’ menawan
Reka bentuk bukaan ideal Aliran udara dan sedutan
yang kuat
Kepingan berpelekat
yang kuat
FP-JM30ELPV_EN_MS_VI_ZH.indb 2 2019/04/08 11:35:54

MS-1
MALAYSIA
MALAYSIA
Terima kasih kerana membeli Pembersih Udara
SHARP ini. Sila baca manual ini dengan teliti.
Sebelum menggunakan produk ini, pastikan
anda membaca bahagian: “Arahan Keselamatan
Penting.”
Selepas membaca manual ini, simpan ia di lokasi
yang mudah dicari untuk rujukan pada masa akan
datang.
Untuk rujukan anda, kami menyarankan agar
anda menyimpan manual ini di tempat di mana
anda mudah untuk membacanya pada bila-bila
masa.
ARAHAN KESELAMATAN
PENTING ..............................................MS-2
NAMA BAHAGIAN ..............................MS-4
PEMASANGAN PENAPIS DAN
KEPINGAN BERPELEKAT .................MS-6
OPERASI .............................................MS-8
PENJAGAAN DAN
PENYELENGGARAAN ......................MS-10
GARIS PANDUAN PENGGANTIAN . . MS-12
PENYELESAIAN MASALAH .............MS-14
SPESIFIKASI .....................................MS-15
ISI KANDUNGAN
Plasmacluster 7000
berketumpatan tinggi
Plasmacluster merawat udara dengan cara yang
sama bagaimana alam semula jadi membersihkan
alam sekitar dengan mengeluarkan ion positif
dan negatif dalam nisbah yang seimbang.
Operasi HAZE yang sesuai
semasa JEREBU berlaku
Mod HAZE membolehkan penghapusan pantas
JEREBU dengan isipadu udara tinggi.
Operasi senyap semasa
menangkap nyamuk pada masa
tidur
Semasa anda bertukar ke mod Sleep, ia
beroperasi secara senyap dengan Ion
Plasmacluster dan lampu penunjuk UV dimatikan
dan cahaya UV kurang terang, sementara fungsi
perangkap nyamuk masih hidup.
Sistem Penapisan
Memerangkap Habuk*2
Prapenapis memerangkap habuk dan zarah-
zarah besar yang lain dalam udara.
Mengurangkan Debunga & Kulapuk*2
Penapis HEPA memerangkap 99.97% zarah
sekecil 0.3 mikron.
*2 Apabila udara dialirkan keluar melalui sistem
penapisan.
FP-JM30ELPV_EN_MS_VI_ZH.indb 1 2019/04/08 11:35:54

MS-2
ARAHAN KESELAMATAN PENTING
Sentiasa ikuti langkah keselamatan
asas semasa menggunakan perkakas
elektrik, termasuk yang berikut:
AMARAN – Sentiasa perhatikan
perkara yang berikut untuk
mengurangkan risiko kejutan elektrik,
kebakaran atau kecederaan:
• Baca semua arahan sebelum
menggunakan unit utama ini.
• Hanya gunakan salur keluar 220-240
volt.
• Perkakas ini tidak direka untuk
digunakan oleh mereka (termasuk
kanak-kanak) yang cacat tubuh
badan, cacat deria atau mental,
mahupun mereka yang kurang
berpengalaman dan pengetahuan,
kecuali jika mereka diberikan
penyeliaan atau arahan yang betul
tentang penggunaan perkakas ini
oleh orang yang bertanggungjawab
atas keselamatan mereka.
Kanak-kanak hendaklah diawasi bagi
memastikan mereka tidak bermain
dengan perkakas ini.
• Jika kord kuasa rosak, ia mesti
digantikan oleh pengilang, wakil
servis, Pusat Servis Sharp yang sah
atau individu yang berkelayakan bagi
mengelakkan bahaya. Sila hubungi
Pusat Servis yang berdekatan bagi
sebarang masalah, pelarasan atau
pembaikan.
• Pastikan anda menanggalkan
palam sebelum menjalankan
penyelenggaraan, apabila
menanggalkan, memasang dan
menggantikan penapis serta apabila
tidak menggunakannya untuk masa
yang lama. Kegagalan melakukan
sedemikian akan menyebabkan litar
pintas berlaku yang mengakibatkan
kejutan elektrik atau kebakaran.
• Jangan gunakan unit utama ini jika
kord kuasa atau palamnya rosak atau
jika sambungan ke salur keluar dinding
longgar.
• Dari semasa ke semasa buang habuk
yang melekat pada palam.
• Jangan masukkan jari atau objek asing ke
dalam salur masuk atau salur keluar udara.
• Sentiasa pegang palam dan jangan
sesekali tarik kordnya apabila hendak
menanggalkan palam kuasa.
Kegagalan melakukan sedemikian akan
menyebabkan litar pintas berlaku yang
mengakibatkan kejutan elektrik atau
kebakaran.
• Berhati-hati agar kord kuasa tidak rosak,
jika tidak, boleh menyebabkan kejutan
elektrik, terlebih panas atau kebakaran.
• Jangan tanggalkan palam dengan tangan
yang basah.
• Jangan letak unit utama ini berdekatan
atau pada objek panas, seperti dapur atau
pemanas, ataupun yang boleh terkena
wap air.
• Jangan kendalikan unit utama ini di dalam
bilik yang menggunakan penyembur
pembunuh serangga. Jangan kendalikan
unit utama ini di dalam bilik yang udaranya
berminyak, berbau asap, terdapat nyalaan
api daripada rokok yang dinyalakan, atau
wasap kimia di udara. Jangan kendalikan
unit utama di tempat yang basah seperti
bilik mandi.
• Sila berhati-hati semasa membersihkan
unit utama ini. Bahan pencuci yang kuat
mengakis boleh merosakkan bahagian
luar unit.
• Jangan dedahkan unit utama kepada air.
Berbuat demikian boleh menyebabkan
litar pintas atau kejutan elektrik.
NOTA – Apa harus dilakukan jika unit
utama mengganggu penerimaan radio atau
TV
Jika pembersih udara mengganggu
penerimaan radio atau televisyen, cuba
salah satu daripada langkah-langkah
berikut:
• Laraskan atau ubah kedudukan antena
penerima.
• Jauhkan unit utama dari radio atau TV.
• Sambungkan peralatan ke dalam salur
keluar pada litar yang berbeza yang
bersambung dengan penerima radio atau
TV.
• Rujuk wakil penjual atau juruteknik radio
atau TV yang berkelayakan.
FP-JM30ELPV_EN_MS_VI_ZH.indb 2 2019/04/08 11:35:54