Winix C545 User manual

7
9
8
10
User Manual
• The product warranty is printed on the back of this guide.
• This product is manufactured for use only in USA / CA.
• This product is suitable for 120 V only.
C545Model
Use & Care
Guide
•Dedicated Call Center: [phone]
•Website: www.winixamerica.com
Contact Winix for
product related inquiries
and customer service
AIR PURIFIER
2610-0256-00 Rev.07
To expedite service, please specify the model name and number, the nature of the problem, your
contact information, and your address.
UNIT SPECIFICATIONS
SAFETY INSTRUCTIONS
Thank you for purchasing a Winix air purifier. This product is for household use only.
• Do not repair or modify the unit. All repairs should be
completed by a qualified technician.
• The plug for this unit is polarized with one blade wider
than the other. Do not force the plug into an electrical
outlet. Do not alter the plug in any way. If the plug does
not fit into the outlet, reverse the plug. If it still does
not fit, contact a qualified technician to install a proper
outlet.
• Do not use if the power cord or plug is damaged or the
connection to the wall outlet is loose.
• Use AC 120V only.
• Do not damage, break, forcefully bend, pull, twist, bundle,
coat, pinch, or place heavy objects on the power cord.
• Periodically remove dust from the power plug.
This will reduce the risk of shock due to humidity build up.
• Remove the power plug from the outlet before cleaning
the unit. When removing the power plug, grasp by
holding the plug itself, never hold by the cord.
• If the power plug is damaged, it must be replaced by
the manufacturer or a qualified technician.
• Remove the power plug from the outlet when not in use.
• Do not handle the power plug with wet hands.
• Do not operate the unit when using indoor smoke-
generating insecticides.
• Do not clean unit with benzene or paint thinner.
Do not spray insecticides on the unit.
• Do not use the unit where it is humid or where the unit
may become wet, such as the bathroom.
• Do not insert fingers or foreign objects into air intake or
outlet.
• Do not use the unit near flammable gases. Do not use
near cigarettes, incense, or other spark-creating items.
• Unit will not remove carbon monoxide emitted from
heating appliances or other sources.
• Unplugging the product disconnects the remote
functions.
IMPORTANT CAUTIONS FOR USING YOUR AIR PURIFIER:
WARNING: Follow the instructions in this manual to reduce the risk of electric shock, short circuit, and/or fire.
Model Name C545
Power Voltage AC 120 V / 60 Hz
Power Rate 65W
Verified Room Size 360sq.ft.
Dimensions 13.7in(W) × 8.4in(D) × 20.5in(H)
Weight 11 lbs
Replacement Filter Filter S / SKU: 1712-0096-00
The exterior, design, and product specifications may be changed without prior notice to improve product performance.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada's license-exempt RSS(s). Operation is subject to the following two conditions:
• This device may not cause interference.
• This device must accept any interference, including interference that may cause undesired operation of the device.
"In French: Cet appareil contient des émetteurs/récepteurs exemptés de licence et conformes aux normes Innovation,
Science et Economic. RSS(s) sans licence de Développement Canada. Le fonctionnement est soumis aux deux conditions
suivantes:
• cet appareil ne doit pas causer d’interférences nuisibles, et
• cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant provoquer un fonctionnement
non souhaité."
Before operating this equipment, carefully read and
follow these safety cautions.
Ensure filters are inserted before running unit.
Running the unit without filters can shorten the
lifespan of the unit and cause electric shock or injury.
Be sure foreign objects are NOT inserted into the
vents on the unit.
Objects can include pins, rods, and coins.
Do not touch any part of the interior of the unit with
wet hands.
The high voltage may cause electric shock.
Ensure unit intake and outlet vents do not become
blocked.
Blockage may lead to increased internal termperatures,
causing product failure and deformation.
Do not use the unit as a step stool or place heavy
objects on the unit.
Personal injury may occur or product failure and
deformation.
WARNING
Follow these instructions to reduce the risk of serious
injury or death and to reduce risk of damaging the unit.
• If the power cord is damaged, it must be replaced
by a special cord. Reassembly is available from the
manufacturer or its service agent.
• This appliance is not intended for use by a person
(including children) with reduced physical sensory or
mental capabilities, or lack of experience and knowledge
of the unit, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do not
play with the appliance.
• This unit is not intended to be used to preserve
documents or art conservation.
Do not pull on the power cord when unplugging the
unit.
Do not tie or knot the power cord when unit is in
operation.
If the unit becomes submerged in water, unplug it
and contact customer service.
Do not unplug or move the unit while in operation.
Do not plug additional appliances into the same
outlet or power supply.
Do not touch the plug with wet hands.
Unplug the unit when not in operation for extended
periods of time.
Do not place around heating elements.
Do not use around mist or fumes from industrial oil
or around large quantities of metallic dust.
The cord can become damaged by forcefully
bending, pulling, twisting, bundling, pinching or
placing heavy objects on it.
Do not install in any sort of motor or transport
vehicle (trucks, boats, ships, etc.).
Do not place in an area with excessive amounts of
noxious gases.
Do not place near any flammable materials
(aerosols, fuel, gases, etc.).
Do not have the unit facing into wind or drafts.
Do not place below any electrical outlet.
Do not place in excessively humid areas where the
unit may become wet.
Do not place unit closer than 12 inches from the
wall during operation. It may cause condensation
on the wall and the surrounding area.
SAFETY AND CAUTIONS
PRODUCT WARRANTY
The terms of the warranty are as follows:
1. This product is manufactured under stringent
quality control and inspections.
2. The warranty will be voided if product failure is a
result of negligence or misuse by the consumer.
3. A proof of purchase must be presented upon
claiming a Product Warranty.
4. Store the proof of purchase in a safe place or
register your product on winixamerica.com to
upload your proof of purchase.
5. This warranty is valid only in the USA and Canada.
* For more information visit
https://winixamerica.com/terms-and-conditions/
Product Name Air Purifier
Model Name C545
Purchase Date
Warranty Period Two (2) Years
Place of Purchase
Place of Purchase tel.
Customer
Address
Name
Tel.
After purchase, be sure to complete all of the above information.
* Certified Refurbished Air Purifiers come with a 1-year
warranty. All Winix Certified Refurbished Air Purifiers go
through a detailed inspection and refurbishment process to
ensure all quality and performance standards are met.
The unit does not turn on at all.
• Is the plug securely attached to the outlet?
- Make sure the outlet has power going to it and ensure
the plug is secured.
• Is there a power outage?
- Check to see if other lights and electrical equipment
are working and try again.
The unit doesn’t work in Auto Mode.
• Has Auto Mode been selected?
- Press the Fan Speed button until Auto Mode is
selected.
• Is the sensor blocked or clogged?
- Wipe Smart Sensor with wet cloth, then dry.
It vibrates and makes a lot of noise.
• Is it running on a slanted or uneven surface?
- Move the unit to a hard, flat, even area.
The power plug and outlet feel hot.
• Is the plug securely plugged in?
- Make sure the plug is properly plugged into the outlet.
There is a strange smell.
• Is it being used in a place with a lot of smoke, dust, or
odors?
- Clean the air intakes on either side and clean the
Pre-Filter.
- Replace the Carbon and the True HEPA Filter.
The fan strength is weak. The unit is not purifying the air.
• Is the Check Filter Indicator light on?
- Change the filters as required.
The display panel is dim.
• Is the Light Sensor blocked by debris?
- When Auto Mode is on, Sleep Mode is automatically
activated when the Light Sensor detects that the room is
dark.
FREQUENTLY ASKED QUESTIONS
The energy efficiency of this ENERGY STAR
certified model is measured based on a ratio
between the model’s CADR for smoke and the
electrical energy it consumes, or CADR/Watt.
IMPORTANT PRECAUTIONS FOR USING YOUR AIR PURIFIER:
• Do not block the intake or outlet vents.
• Do not use near hot objects, such as a stove.
• Do not use where the unit may come into contact with steam.
• Do not use the unit on its side.
• Keep away from products that generate oily residue,
such as a deep fryer.
• Do not use detergent to clean the unit.
• Do not operate without a filter.
• Do not wash and reuse the True HEPA Filter.
• Hold the handle on the back of the unit to transport.
• Do not hold by the front panel.
• Do not stick any small objects into the air outlet vents or
fan.
EPA Est. No: 99260-THA-1

1
4
2
5
3
6
01. Pre-Filter
Designed to catch larger airborne particles found
indoors.
03. True HEPA Filter
Winix True HEPA captures 99.97%* of airborne
allergens including pollen, dust, smoke, pet dander, and
other particles as small as 0.3 microns.
*Based on independent laboratory tests conducted on
inanimate particles as small as 0.3 microns.
02. Activated Carbon Filter
Reduces VOCs and household odors from cooking,
pets, and smoke.
04. PlasmaWave
®
Winix PlasmaWave
®
Technology reduces airborne
Bacteria
1
& Influenza A Virus
2
.
1
Tested against P. aeruginosa, Salmonella typhimurium,
E. Coli, and Staph A. in a 4m
3
chamber and unit must
operate continuously for 1 hour to achieve 99.9% reduction.
2
Tested against Influenza A Virus H3N2 in a 1m
3
chamber
and unit must operate continuously for 1 hour to achieve
99.6% reduction.
FRONT
PACKAGE CONTENTS
BACK
Control Panel
* For a Certified Refurbished Air Purifier, there will be 4 New Carbon Filters and 1 True HEPA Filter included;
equivalent to a 1-year supply.
Front Panel
Air Outlet
Vent
Handle
Power Plug
Unit (1) Pre-Filter
(8) Activated Carbon Filters
(2) True HEPA Filters
Alexa Setup Guide /
Wi-Fi Setup Guide
User
Manual
WHERE TO USE
MODEL PART DIAGRAM
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
07 08 09 11 13
02 03 04 05 0601
1210
01. Auto Mode Indicator
The LED "Auto" light will indicate when Auto Mode is
activated.
02. Air Quality Indicator
Color coded LED light indicates one of three levels of
Air Quality: Red (poor), Amber (fair), and Blue (good).
03. Fan Speed Indicator
Indicates the current fan speed.
Auto Mode Low Medium High Turbo
04. Sleep Mode Indicator
The LED "Sleep" light will indicate when Sleep Mode is
activated.
05. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
06. Filter Reset Button
After replacing the True HEPA Filter, use a small object
such as a paper clip, to press and hold the Filter
Reset Button for at least 5 seconds until the Filter
Replacement Indicator turns off.
07. Smart Sensor
Detects the amount of odorous gas in the environment.
When in Auto mode, the fan speed adjusts according to
the detected amount of gas.
08. Power Button
Turns the unit on or off. During the first 30 seconds of
powering up, the Air Quality Indicator will cycle through
Blue, Amber and Red colors.
• Smart sensor takes approximately 4 minutes to detect
the air quality in the environment before normal
operation begins.
CONTROL PANEL
09-1. Fan Speed/Auto/Sleep Buttons
Use the Fan Speed arrow buttons to set the desired
fan speed. Fan Speeds cycle over in this sequence:
Auto, Low, Medium, High, Turbo, Sleep, Auto.
Auto Mode:
• Auto Mode automatically adjusts fan speeds according
to your indoor air quality. The fan speed will adjust to
low when air quality is good, medium when fair, and to
high when poor.
Sleep Mode:
When Sleep Mode is activated, the Air Quality Indicator
LED light is disabled.
• Fan speed will automatically set to minimum speed
(lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave®will be
disabled, but it can be turned back on.
09-2. PlasmaWave
®
Button
Press and hold the two arrow buttons +for
3 seconds
Press the Plasmawave
®
button when the unit is on to
enable or disable this feature. By default, PlasmaWave
®
is enabled whenever the unit is powered on.
"When the unit is running, you may hear a chirping
or buzzing sound. The sound is from large particles
passing through PlasmaWave
®
, it is normal and does
not signify product failure."
10. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or disabled.
11. Wi-Fi Button
• Press for 3 seconds to activate pairing mode.
• When Wi-Fi is paired, press the button to turn Wi-Fi off
or back on.
12. Wi-Fi Indicator
• Enables or disables the Wi-Fi feature.
• When in the pairing state, the Wi-Fi LED flashes.
• When paired successfully, the Wi-Fi LED will be a solid
white light.
13. Light Sensor
Detects the amount of ambient light in the environment.
When in Auto Mode, the light sensor detects when to
put the unit into Sleep Mode.
Winix Smart Wi-Fi Setup
Before you begin, make sure you have a wireless router
that is 2.4Ghz or newer and have a Smartphone that is
Android5.0 and later or iOS10.0 and later. Reference
the Winix Smart Wi-Fi Set Up Guide for more details.
• Latest Phone Operating System requirements are
subject to change based on future phone technology
and app version updates.
• Make sure to disable any VPN networks before
connecting your unit.
1. Download the Winix Smart app on your device.
• available via Google Play store or iTunes App store.
2. Run the app and follow the setup guide to connect
your device to the unit.
① Select "New Unit" and choose C545 to connect
to this model.
② Read the notice and select "OK".
③ Enter the password to your Wi-Fi network.
④ Press and hold the Wi-Fi button on the unit's
control panel until it beeps.
• The Wi-Fi strength indicator will begin to blink.
⑤ Connect to the Winix Smart network via your
device's network menu.
⑥ Selecting "Next" will connect your unit to your
device.
⑦ Define the unit settings (Name and Location).
⑧ When set up is complete, the Winix Smart
Indicator will light up.
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Clean once every 14 days Permanent
Activated
Carbon Filter
none
Can NOT be WASHED
Replace every 3 months
True HEPA Filter
Lasts Approx.
12 months
• When the Check Filter Indicator LED is on, it is time to replace the Filter.
• Intervals between filter replacement may vary depending on environment.
MAINTENANCE
3True HEPA Filter
2Activated Carbon Filter 4PlasmaWave®
Pre-Filter
1
4-STAGE AIR PURIFICATION INITIAL OPERATION
Latch
1. Remove the front panel by grasping its upper
edge and gently pulling forward.
2. Remove the Pre-Filter, then the bag of filters
behind it.
3. Remove filters from protective plastic bag.
01
02
03
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Activated Carbon Filter (middle)
01. Pre-Filter (front)
Latch
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
1712-0096-00
Resetting Filter Life:
After replacing your True HEPA Filter, place
the Pre-Filter back in and close the Front
Panel. While the unit is on, hold the Filter
Reset Button for at least 5 seconds until
you hear the beep. After the beep, the Filter
Replacement Indicator will disappear.
Your Winix True HEPA is now reset.
REPLACING FILTERS
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean
the Pre-Filter.
• If it is excessively soiled, rinse in room temperature
water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before using.
• Intervals between filter cleaning may vary depending
on the air quality.
• Do not use hot water over 104oF or volatile fluids such
as paint thinner.
NOTICE
Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room temperature
water.
• Afterwards, wipe it down with a clean, dry cloth.
Open the front panel and clean the interior with a
vacuum cleaner.
• For optimal performance, clean every 1-2 months.
NOTICE
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.

1
4
2
5
3
6
01. Pre-Filter
Designed to catch larger airborne particles found
indoors.
03. True HEPA Filter
Winix True HEPA captures 99.97%* of airborne
allergens including pollen, dust, smoke, pet dander, and
other particles as small as 0.3 microns.
*Based on independent laboratory tests conducted on
inanimate particles as small as 0.3 microns.
02. Activated Carbon Filter
Reduces VOCs and household odors from cooking,
pets, and smoke.
04. PlasmaWave
®
Winix PlasmaWave
®
Technology reduces airborne
Bacteria
1
& Influenza A Virus
2
.
1
Tested against P. aeruginosa, Salmonella typhimurium,
E. Coli, and Staph A. in a 4m
3
chamber and unit must
operate continuously for 1 hour to achieve 99.9% reduction.
2
Tested against Influenza A Virus H3N2 in a 1m
3
chamber
and unit must operate continuously for 1 hour to achieve
99.6% reduction.
FRONT
PACKAGE CONTENTS
BACK
Control Panel
* For a Certified Refurbished Air Purifier, there will be 4 New Carbon Filters and 1 True HEPA Filter included;
equivalent to a 1-year supply.
Front Panel
Air Outlet
Vent
Handle
Power Plug
Unit (1) Pre-Filter
(8) Activated Carbon Filters
(2) True HEPA Filters
Alexa Setup Guide /
Wi-Fi Setup Guide
User
Manual
WHERE TO USE
MODEL PART DIAGRAM
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
07 08 09 11 13
02 03 04 05 0601
1210
01. Auto Mode Indicator
The LED "Auto" light will indicate when Auto Mode is
activated.
02. Air Quality Indicator
Color coded LED light indicates one of three levels of
Air Quality: Red (poor), Amber (fair), and Blue (good).
03. Fan Speed Indicator
Indicates the current fan speed.
Auto Mode Low Medium High Turbo
04. Sleep Mode Indicator
The LED "Sleep" light will indicate when Sleep Mode is
activated.
05. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
06. Filter Reset Button
After replacing the True HEPA Filter, use a small object
such as a paper clip, to press and hold the Filter
Reset Button for at least 5 seconds until the Filter
Replacement Indicator turns off.
07. Smart Sensor
Detects the amount of odorous gas in the environment.
When in Auto mode, the fan speed adjusts according to
the detected amount of gas.
08. Power Button
Turns the unit on or off. During the first 30 seconds of
powering up, the Air Quality Indicator will cycle through
Blue, Amber and Red colors.
• Smart sensor takes approximately 4 minutes to detect
the air quality in the environment before normal
operation begins.
CONTROL PANEL
09-1. Fan Speed/Auto/Sleep Buttons
Use the Fan Speed arrow buttons to set the desired
fan speed. Fan Speeds cycle over in this sequence:
Auto, Low, Medium, High, Turbo, Sleep, Auto.
Auto Mode:
• Auto Mode automatically adjusts fan speeds according
to your indoor air quality. The fan speed will adjust to
low when air quality is good, medium when fair, and to
high when poor.
Sleep Mode:
When Sleep Mode is activated, the Air Quality Indicator
LED light is disabled.
• Fan speed will automatically set to minimum speed
(lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave®will be
disabled, but it can be turned back on.
09-2. PlasmaWave
®
Button
Press and hold the two arrow buttons +for
3 seconds
Press the Plasmawave
®
button when the unit is on to
enable or disable this feature. By default, PlasmaWave
®
is enabled whenever the unit is powered on.
"When the unit is running, you may hear a chirping
or buzzing sound. The sound is from large particles
passing through PlasmaWave
®
, it is normal and does
not signify product failure."
10. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or disabled.
11. Wi-Fi Button
• Press for 3 seconds to activate pairing mode.
• When Wi-Fi is paired, press the button to turn Wi-Fi off
or back on.
12. Wi-Fi Indicator
• Enables or disables the Wi-Fi feature.
• When in the pairing state, the Wi-Fi LED flashes.
• When paired successfully, the Wi-Fi LED will be a solid
white light.
13. Light Sensor
Detects the amount of ambient light in the environment.
When in Auto Mode, the light sensor detects when to
put the unit into Sleep Mode.
Winix Smart Wi-Fi Setup
Before you begin, make sure you have a wireless router
that is 2.4Ghz or newer and have a Smartphone that is
Android5.0 and later or iOS10.0 and later. Reference
the Winix Smart Wi-Fi Set Up Guide for more details.
• Latest Phone Operating System requirements are
subject to change based on future phone technology
and app version updates.
• Make sure to disable any VPN networks before
connecting your unit.
1. Download the Winix Smart app on your device.
• available via Google Play store or iTunes App store.
2. Run the app and follow the setup guide to connect
your device to the unit.
① Select "New Unit" and choose C545 to connect
to this model.
② Read the notice and select "OK".
③ Enter the password to your Wi-Fi network.
④ Press and hold the Wi-Fi button on the unit's
control panel until it beeps.
• The Wi-Fi strength indicator will begin to blink.
⑤ Connect to the Winix Smart network via your
device's network menu.
⑥ Selecting "Next" will connect your unit to your
device.
⑦ Define the unit settings (Name and Location).
⑧ When set up is complete, the Winix Smart
Indicator will light up.
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Clean once every 14 days Permanent
Activated
Carbon Filter
none
Can NOT be WASHED
Replace every 3 months
True HEPA Filter
Lasts Approx.
12 months
• When the Check Filter Indicator LED is on, it is time to replace the Filter.
• Intervals between filter replacement may vary depending on environment.
MAINTENANCE
3True HEPA Filter
2Activated Carbon Filter 4PlasmaWave®
Pre-Filter
1
4-STAGE AIR PURIFICATION INITIAL OPERATION
Latch
1. Remove the front panel by grasping its upper
edge and gently pulling forward.
2. Remove the Pre-Filter, then the bag of filters
behind it.
3. Remove filters from protective plastic bag.
01
02
03
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Activated Carbon Filter (middle)
01. Pre-Filter (front)
Latch
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
1712-0096-00
Resetting Filter Life:
After replacing your True HEPA Filter, place
the Pre-Filter back in and close the Front
Panel. While the unit is on, hold the Filter
Reset Button for at least 5 seconds until
you hear the beep. After the beep, the Filter
Replacement Indicator will disappear.
Your Winix True HEPA is now reset.
REPLACING FILTERS
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean
the Pre-Filter.
• If it is excessively soiled, rinse in room temperature
water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before using.
• Intervals between filter cleaning may vary depending
on the air quality.
• Do not use hot water over 104oF or volatile fluids such
as paint thinner.
NOTICE
Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room temperature
water.
• Afterwards, wipe it down with a clean, dry cloth.
Open the front panel and clean the interior with a
vacuum cleaner.
• For optimal performance, clean every 1-2 months.
NOTICE
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.

1
4
2
5
3
6
01. Pre-Filter
Designed to catch larger airborne particles found
indoors.
03. True HEPA Filter
Winix True HEPA captures 99.97%* of airborne
allergens including pollen, dust, smoke, pet dander, and
other particles as small as 0.3 microns.
*Based on independent laboratory tests conducted on
inanimate particles as small as 0.3 microns.
02. Activated Carbon Filter
Reduces VOCs and household odors from cooking,
pets, and smoke.
04. PlasmaWave
®
Winix PlasmaWave
®
Technology reduces airborne
Bacteria
1
& Influenza A Virus
2
.
1
Tested against P. aeruginosa, Salmonella typhimurium,
E. Coli, and Staph A. in a 4m
3
chamber and unit must
operate continuously for 1 hour to achieve 99.9% reduction.
2
Tested against Influenza A Virus H3N2 in a 1m
3
chamber
and unit must operate continuously for 1 hour to achieve
99.6% reduction.
FRONT
PACKAGE CONTENTS
BACK
Control Panel
* For a Certified Refurbished Air Purifier, there will be 4 New Carbon Filters and 1 True HEPA Filter included;
equivalent to a 1-year supply.
Front Panel
Air Outlet
Vent
Handle
Power Plug
Unit (1) Pre-Filter
(8) Activated Carbon Filters
(2) True HEPA Filters
Alexa Setup Guide /
Wi-Fi Setup Guide
User
Manual
WHERE TO USE
MODEL PART DIAGRAM
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
07 08 09 11 13
02 03 04 05 0601
1210
01. Auto Mode Indicator
The LED "Auto" light will indicate when Auto Mode is
activated.
02. Air Quality Indicator
Color coded LED light indicates one of three levels of
Air Quality: Red (poor), Amber (fair), and Blue (good).
03. Fan Speed Indicator
Indicates the current fan speed.
Auto Mode Low Medium High Turbo
04. Sleep Mode Indicator
The LED "Sleep" light will indicate when Sleep Mode is
activated.
05. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
06. Filter Reset Button
After replacing the True HEPA Filter, use a small object
such as a paper clip, to press and hold the Filter
Reset Button for at least 5 seconds until the Filter
Replacement Indicator turns off.
07. Smart Sensor
Detects the amount of odorous gas in the environment.
When in Auto mode, the fan speed adjusts according to
the detected amount of gas.
08. Power Button
Turns the unit on or off. During the first 30 seconds of
powering up, the Air Quality Indicator will cycle through
Blue, Amber and Red colors.
• Smart sensor takes approximately 4 minutes to detect
the air quality in the environment before normal
operation begins.
CONTROL PANEL
09-1. Fan Speed/Auto/Sleep Buttons
Use the Fan Speed arrow buttons to set the desired
fan speed. Fan Speeds cycle over in this sequence:
Auto, Low, Medium, High, Turbo, Sleep, Auto.
Auto Mode:
• Auto Mode automatically adjusts fan speeds according
to your indoor air quality. The fan speed will adjust to
low when air quality is good, medium when fair, and to
high when poor.
Sleep Mode:
When Sleep Mode is activated, the Air Quality Indicator
LED light is disabled.
• Fan speed will automatically set to minimum speed
(lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave®will be
disabled, but it can be turned back on.
09-2. PlasmaWave
®
Button
Press and hold the two arrow buttons +for
3 seconds
Press the Plasmawave
®
button when the unit is on to
enable or disable this feature. By default, PlasmaWave
®
is enabled whenever the unit is powered on.
"When the unit is running, you may hear a chirping
or buzzing sound. The sound is from large particles
passing through PlasmaWave
®
, it is normal and does
not signify product failure."
10. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or disabled.
11. Wi-Fi Button
• Press for 3 seconds to activate pairing mode.
• When Wi-Fi is paired, press the button to turn Wi-Fi off
or back on.
12. Wi-Fi Indicator
• Enables or disables the Wi-Fi feature.
• When in the pairing state, the Wi-Fi LED flashes.
• When paired successfully, the Wi-Fi LED will be a solid
white light.
13. Light Sensor
Detects the amount of ambient light in the environment.
When in Auto Mode, the light sensor detects when to
put the unit into Sleep Mode.
Winix Smart Wi-Fi Setup
Before you begin, make sure you have a wireless router
that is 2.4Ghz or newer and have a Smartphone that is
Android5.0 and later or iOS10.0 and later. Reference
the Winix Smart Wi-Fi Set Up Guide for more details.
• Latest Phone Operating System requirements are
subject to change based on future phone technology
and app version updates.
• Make sure to disable any VPN networks before
connecting your unit.
1. Download the Winix Smart app on your device.
• available via Google Play store or iTunes App store.
2. Run the app and follow the setup guide to connect
your device to the unit.
① Select "New Unit" and choose C545 to connect
to this model.
② Read the notice and select "OK".
③ Enter the password to your Wi-Fi network.
④ Press and hold the Wi-Fi button on the unit's
control panel until it beeps.
• The Wi-Fi strength indicator will begin to blink.
⑤ Connect to the Winix Smart network via your
device's network menu.
⑥ Selecting "Next" will connect your unit to your
device.
⑦ Define the unit settings (Name and Location).
⑧ When set up is complete, the Winix Smart
Indicator will light up.
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Clean once every 14 days Permanent
Activated
Carbon Filter
none
Can NOT be WASHED
Replace every 3 months
True HEPA Filter
Lasts Approx.
12 months
• When the Check Filter Indicator LED is on, it is time to replace the Filter.
• Intervals between filter replacement may vary depending on environment.
MAINTENANCE
3True HEPA Filter
2Activated Carbon Filter 4PlasmaWave®
Pre-Filter
1
4-STAGE AIR PURIFICATION INITIAL OPERATION
Latch
1. Remove the front panel by grasping its upper
edge and gently pulling forward.
2. Remove the Pre-Filter, then the bag of filters
behind it.
3. Remove filters from protective plastic bag.
01
02
03
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Activated Carbon Filter (middle)
01. Pre-Filter (front)
Latch
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
1712-0096-00
Resetting Filter Life:
After replacing your True HEPA Filter, place
the Pre-Filter back in and close the Front
Panel. While the unit is on, hold the Filter
Reset Button for at least 5 seconds until
you hear the beep. After the beep, the Filter
Replacement Indicator will disappear.
Your Winix True HEPA is now reset.
REPLACING FILTERS
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean
the Pre-Filter.
• If it is excessively soiled, rinse in room temperature
water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before using.
• Intervals between filter cleaning may vary depending
on the air quality.
• Do not use hot water over 104oF or volatile fluids such
as paint thinner.
NOTICE
Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room temperature
water.
• Afterwards, wipe it down with a clean, dry cloth.
Open the front panel and clean the interior with a
vacuum cleaner.
• For optimal performance, clean every 1-2 months.
NOTICE
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.

1
4
2
5
3
6
01. Pre-Filter
Designed to catch larger airborne particles found
indoors.
03. True HEPA Filter
Winix True HEPA captures 99.97%* of airborne
allergens including pollen, dust, smoke, pet dander, and
other particles as small as 0.3 microns.
*Based on independent laboratory tests conducted on
inanimate particles as small as 0.3 microns.
02. Activated Carbon Filter
Reduces VOCs and household odors from cooking,
pets, and smoke.
04. PlasmaWave
®
Winix PlasmaWave
®
Technology reduces airborne
Bacteria
1
& Influenza A Virus
2
.
1
Tested against P. aeruginosa, Salmonella typhimurium,
E. Coli, and Staph A. in a 4m
3
chamber and unit must
operate continuously for 1 hour to achieve 99.9% reduction.
2
Tested against Influenza A Virus H3N2 in a 1m
3
chamber
and unit must operate continuously for 1 hour to achieve
99.6% reduction.
FRONT
PACKAGE CONTENTS
BACK
Control Panel
* For a Certified Refurbished Air Purifier, there will be 4 New Carbon Filters and 1 True HEPA Filter included;
equivalent to a 1-year supply.
Front Panel
Air Outlet
Vent
Handle
Power Plug
Unit (1) Pre-Filter
(8) Activated Carbon Filters
(2) True HEPA Filters
Alexa Setup Guide /
Wi-Fi Setup Guide
User
Manual
WHERE TO USE
MODEL PART DIAGRAM
12~18 in
12~18 in
Allow 12 ~ 18 in. of space between TVs, radios, and other electronics
Electromagnetic interference from certain electronics may cause
product malfunction.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and vibrations.
Allow at least 12 ~ 18 in. from walls for maximum air flow
07 08 09 11 13
02 03 04 05 0601
1210
01. Auto Mode Indicator
The LED "Auto" light will indicate when Auto Mode is
activated.
02. Air Quality Indicator
Color coded LED light indicates one of three levels of
Air Quality: Red (poor), Amber (fair), and Blue (good).
03. Fan Speed Indicator
Indicates the current fan speed.
Auto Mode Low Medium High Turbo
04. Sleep Mode Indicator
The LED "Sleep" light will indicate when Sleep Mode is
activated.
05. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
06. Filter Reset Button
After replacing the True HEPA Filter, use a small object
such as a paper clip, to press and hold the Filter
Reset Button for at least 5 seconds until the Filter
Replacement Indicator turns off.
07. Smart Sensor
Detects the amount of odorous gas in the environment.
When in Auto mode, the fan speed adjusts according to
the detected amount of gas.
08. Power Button
Turns the unit on or off. During the first 30 seconds of
powering up, the Air Quality Indicator will cycle through
Blue, Amber and Red colors.
• Smart sensor takes approximately 4 minutes to detect
the air quality in the environment before normal
operation begins.
CONTROL PANEL
09-1. Fan Speed/Auto/Sleep Buttons
Use the Fan Speed arrow buttons to set the desired
fan speed. Fan Speeds cycle over in this sequence:
Auto, Low, Medium, High, Turbo, Sleep, Auto.
Auto Mode:
• Auto Mode automatically adjusts fan speeds according
to your indoor air quality. The fan speed will adjust to
low when air quality is good, medium when fair, and to
high when poor.
Sleep Mode:
When Sleep Mode is activated, the Air Quality Indicator
LED light is disabled.
• Fan speed will automatically set to minimum speed
(lower than 'Low') which will be nearly silent.
• When Sleep Mode is active, PlasmaWave®will be
disabled, but it can be turned back on.
09-2. PlasmaWave
®
Button
Press and hold the two arrow buttons +for
3 seconds
Press the Plasmawave
®
button when the unit is on to
enable or disable this feature. By default, PlasmaWave
®
is enabled whenever the unit is powered on.
"When the unit is running, you may hear a chirping
or buzzing sound. The sound is from large particles
passing through PlasmaWave
®
, it is normal and does
not signify product failure."
10. PlasmaWave
®
Indicator
Indicates whether PlasmaWave
®
is enabled or disabled.
11. Wi-Fi Button
• Press for 3 seconds to activate pairing mode.
• When Wi-Fi is paired, press the button to turn Wi-Fi off
or back on.
12. Wi-Fi Indicator
• Enables or disables the Wi-Fi feature.
• When in the pairing state, the Wi-Fi LED flashes.
• When paired successfully, the Wi-Fi LED will be a solid
white light.
13. Light Sensor
Detects the amount of ambient light in the environment.
When in Auto Mode, the light sensor detects when to
put the unit into Sleep Mode.
Winix Smart Wi-Fi Setup
Before you begin, make sure you have a wireless router
that is 2.4Ghz or newer and have a Smartphone that is
Android5.0 and later or iOS10.0 and later. Reference
the Winix Smart Wi-Fi Set Up Guide for more details.
• Latest Phone Operating System requirements are
subject to change based on future phone technology
and app version updates.
• Make sure to disable any VPN networks before
connecting your unit.
1. Download the Winix Smart app on your device.
• available via Google Play store or iTunes App store.
2. Run the app and follow the setup guide to connect
your device to the unit.
① Select "New Unit" and choose C545 to connect
to this model.
② Read the notice and select "OK".
③ Enter the password to your Wi-Fi network.
④ Press and hold the Wi-Fi button on the unit's
control panel until it beeps.
• The Wi-Fi strength indicator will begin to blink.
⑤ Connect to the Winix Smart network via your
device's network menu.
⑥ Selecting "Next" will connect your unit to your
device.
⑦ Define the unit settings (Name and Location).
⑧ When set up is complete, the Winix Smart
Indicator will light up.
When to Replace Filters
Filter Indicator Light When to Service When to Replace
Pre-Filter none Clean once every 14 days Permanent
Activated
Carbon Filter
none
Can NOT be WASHED
Replace every 3 months
True HEPA Filter
Lasts Approx.
12 months
• When the Check Filter Indicator LED is on, it is time to replace the Filter.
• Intervals between filter replacement may vary depending on environment.
MAINTENANCE
3True HEPA Filter
2Activated Carbon Filter 4PlasmaWave®
Pre-Filter
1
4-STAGE AIR PURIFICATION INITIAL OPERATION
Latch
1. Remove the front panel by grasping its upper
edge and gently pulling forward.
2. Remove the Pre-Filter, then the bag of filters
behind it.
3. Remove filters from protective plastic bag.
01
02
03
4. Install the filters until they fit securely in place.
03. True HEPA Filter (back)
02. Activated Carbon Filter (middle)
01. Pre-Filter (front)
Latch
5. After filters are installed, close the front panel.
6. Insert the power cord into an electrical outlet.
1712-0096-00
Resetting Filter Life:
After replacing your True HEPA Filter, place
the Pre-Filter back in and close the Front
Panel. While the unit is on, hold the Filter
Reset Button for at least 5 seconds until
you hear the beep. After the beep, the Filter
Replacement Indicator will disappear.
Your Winix True HEPA is now reset.
REPLACING FILTERS
CLEANING CARE
Cleaning the Filters:
Use a vacuum cleaner or soft brush to clean
the Pre-Filter.
• If it is excessively soiled, rinse in room temperature
water.
• Do not use detergent or soap.
• Allow the filter to dry for 24 hours or more before using.
• Intervals between filter cleaning may vary depending
on the air quality.
• Do not use hot water over 104oF or volatile fluids such
as paint thinner.
NOTICE
Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room temperature
water.
• Afterwards, wipe it down with a clean, dry cloth.
Open the front panel and clean the interior with a
vacuum cleaner.
• For optimal performance, clean every 1-2 months.
NOTICE
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
• Before cleaning or maintaining, ensure unit is unplugged.