Sodex Sport S12211 User manual

DESCRIPTION
Alu structure 100x120
Powder coated
7.32m x 2.44m
CONFORM
European norm
EN 748
PRODUCT SHEET
ALUMINIUM OVOID FOOTBALL
GOALS, 7.32x2.44M, SOCKETED
PRODUCT REF :S12211 PAIR
ASSEMBLY TIME
The assembly time for this goal is estimated at 10 minutes with 2 people (without sealing).
TEST AFTER INSTALLATION
According to the regulation above, this product has to be tested like below:
- Put 180kg at 20cm from the ground and in the middle of the crossbar during 1min.
- Apply an horizontal force of 110 kg on the middle of the crossbar, thanks to a 3 meters rope, during 1min.
After these tests, the equipment and the fixation system should not have break, move or show residual defor-
mation.
During the first installation, stability and strength tests are compulsory.
Every time you install the equipment, a visual check of the stability and strength must be realized.
The owner of this equipment must usually control the product.
For an optimal use of our products, we advise to follow the installation and maintenance instructions.
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to be done
within the legal period of the reception of the material. The warranty will not apply to:
- All degradation during the transport.
- All degradation due to use differing from which was intended.
- All degradation due to poor maintenance.
- Any defect claimed after the end of the legal period.
- Any damaged due to a faulty installation and assembly of the module.

2
FIXATION AND SEALING
INSTALLATION OF THE POST IN THE SOCKET : 350 mm
500 mm
NB: all the dimension are in millimetre
- Dig holes for the concrete blocks according to
the dimensions above and on the left.
- Fill the bottom of the holes with CPJ 45
concrete dosed at 350 kg/m³ . Put the sockets
in position, according to the sceme. When the
position is correct, fill the rest of the holes, and
adjust the position of the sockets.
- Let the concrete dry for at least 72 hours
(depending on the weather).
Tips: You can put the goal in position during
the drying of the concrete blocks. Use a plastic
film to protect the bottom of the post, and put
the goal into the sockets. Then use wooden
shims to maintain the goal in good position.
Goal line Penalty axis
Socket axis
Sealing of concrete
3710 3710
7420

3
ASSEMBLY
NECESSARY
ITEMS
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
SS Screw M10x30 +
SS washer M10
1– ASSEMBLY OF THE POSTS TO THE CROSSBAR (x4)
Mallet
Allen key 6mm
Wrench 13mm Wrench 10mm
x4
SS Screws
M10x30
SS Screws
M8x50
x4 x4
SS Washers 10
x8
SS Washers 8
x4
SS Washers 6
Joint bars M6x25
x4
U plates
x4
x4
SS Locknut M8
x4
SS Locknut M6
POST
CROSSBAR
STEP 1 STEP 2
x1
SS Screws
M10x30
x1
SS Washers 10
Caps D16
x12
Note: When mounted, pay attention
carefully. The bolts are only slightly
tight. After the last checking, all thing
are correct, tighten the bolts. These holes are useful if a top
net support is used. If there is no
top net support on the goal,
thanks to use caps Ø16 to fill the
holes, in order to avoid any risk
of finger entrapment.
Caps D16
x3

4
MONTAGE
NECESSARY
ITEMS
Joint bar M6x25
SS Screw M8x50
+ SS washers 8
+ SS locknut M8
U plates
SS washer 6
+ SS locknut M6
SS Screws
M8x50
x1 x2
SS Washers 8
x1
SS Washers 6
U plates
x1
Joint bars M6x25
x1 x1
SS Locknut M8
x1
SS Locknut M6
2– ASSEMBLY OF THE NET LIFTING SYSTEM (x4)

NOMENCLATURE
Pack-
age N° Ref Index Designation Description Quanti- ty Packing Method Weight (kg)
Dim.
(mm)
A1 S12211-01 BCrossbar 1
Plastic bubbles +
cardboard 5
layers
23.5 7550x200x140
A2 S12211-01 BCrossbar 1
Plastic bubbles +
cardboard 5
layers
23.5 7550x200x140
A3 S12211-02 +
S12483-01 B + A Post + Sleeve 2 + 2
Plastic bubbles +
cardboard 5
layers
18.4 2950x220x160
A4 S12211-02 +
S12483-02 B + A Post + Sleeve 2 + 2
Plastic bubbles +
cardboard 5
layers
18.4 2950x220x160
A5 S12211-09 CAccessories 1Cardboard 5
layers 1.6 150x100x100
ACCESSORIES PUT IN A CLEAR PVC BAG
Pack-
age N° Ref Designation Description Qty Note
A5
BITH0850 +
LITA081815 +
TITD08
SS Screws M8x50 +
SS washers 8 +
SS locknuts M8
4 + 8 + 4 Fix the lifting system
A5 U Plates 4Fix the lifting system
A5 BITK1030 +
LITA102220
SS Screws M10x30 +
SS washers M10 4 + 4 Assembly of the crossbar to the posts
A5 LITA062010 +
TITD06
Joint bars M6x25 +
SS washers 6 +
SS Locknuts M6
4 + 4 + 4 Fix the lifting system
A5 NNT16 Caps D16 12
To fill the unused holes
on the posts and
crossbars
PRE-ASSEMBLED ACCESSORIES
Pack-
age N° Ref Designation Description Qty Note
A3 +
A4
BITK1030 +
LITA102220
SS Screws M10x30 +
SS washers M10 4 + 4 Assembly of the post to the sleeve
A1 +
A2 +
A3 +
A4
S12364 Hooks 1 fixation 76 Fix to the goals
A3 +
A4 Conformity stickers 2
VISA PACKING DEPARTMENT DATE :
PACKING LIST
ALUMINIUM OVOID FOOTBALL
GOALS, 7.32x2.44M, SOCKETED
PRODUCT REF S12211 Index C PAIR