Sodex Sport S30158 User manual

1 1
DETAILS
SODEX INTERNATIONAL
18 rue de l’avenir – Bât. 224
14650 CARPIQUET
Tel: + 33 (0) 2.31.53.78.70
Email: [email protected]
DESCRIPTION
Structure en alu D90
Plastifié
CONFORM
European standard
NF EN 1271
ASSEMBLY INSTRUCTIONS
VOLLEYBALL POSTS, TO SEAL, D90,
CAPSTAN TENSION
PRODUCT REF:S30158 PAIR
ASSEMBLY TIME
The time to make the assembly of this volleyball posts is estimated for 2 persons, at 30minutes. (without sealing).
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufactu-
rer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labor guarantee. Every claim regarding the condition of the delivered equipment has to be
done within the legal period,of the reception of the material.
The warranty will not apply to:
- All degradation during the transport.
- All degradation due to poor maintenance.
- All degradation due to use differing from which was intended
- Any defect claimed after the end of the legal period.
- Any damage due to a faulty installation or assembly of the module

2 2
The posts need to have a minimum spacing of 10m and maximum 11m.
We advice 11m. However, check carefully the length of the cable of your net before
defining the spacing between the posts.
Sealing
Pitch axis
Socket positions
IMPLANTATION AND SEALING
(FOR INDOOR AND OUTDOOR VOLLEYBALL)

3 3
PENETRATION OF THE POST INTO THE SOCKET : 400 mm
IMPLANTATION AND SEALING
(FOR BEACH VOLLEY)
The distance between the center of the
posts must be between 9.5m and 10.1m. We
recommend 9.6m. Nevertheless, please
check the length of the cable before setting
the anchorages.
- Dig two holes (1 per baseframe) with a depth
of 500mm, a length of 1200mm and a width of
800mm, according to the opposite drawing.
- Set the baseframe with the reinforcing bar on
the opposite side of the pitch.

4 4
ASSEMBLY
NECESSARY TOOLS (NON INCLUDED)
ELEMENTS FOURNIS
NECESSARY
ITEMS
1– ASSEMBLY OF PULLEYS (X2)
SS Screw M10x30
+ SS washers M10
+ SS locknut M10
Pulley
Tighten the assembly softly to allow
a good rotation of the pulley.
X1
Capstan with
stainless steel ‘S’
hook
X2
Turning ring
stainless steel M8
ASSEMBLY
Wrench 17mm
X2
Pulley
X2
Bracket M8
X1
Turning knob M10 +
wire D6
X1
Pulley
X2
SS Screws
M10x30
X4
SS Washers 10
X2
SS Locknut
M10
X1
SS Screws
M10x30
X2
SS Washers 10
X1
SS Locknut
M10

5 5
ASSEMBLY
2 - ASSEMBLY OF SLIDING BARS
NECESSARY
ITEMS
SLIDING BAR WITHOUT CAPSTAN SLIDING BAR WITH CAPSTAN
The sliding bar needs to be put on the
inner side of the playing zone after posi-
tioning the posts.
The sliding bar needs to be put on the
inner side of the playing zone after posi-
tioning the posts.
X2
Turning ring M8
X2
Bracket M8
Sliding bar
Turning ring M8
Assemble the sliding
bar by the bottom of
the post
Bracket
Sliding bar
Turning ring M8
Assemble the sliding
bar by the bottom of
the post
Bracket

6 6
3– NET HEIGHT SETTING
NECESSARY
ITEMS
Turning ring M8
Line
Graduated sticker
ASSEMBLY
Make sure that the height at the middle of the net once this one is tensioned is 2.43m for a
men’s competition (2.24m for women’s competition). It is advised to adjust the height at
the end of the net 2cm higher than the one desired in the middle. Nevertheless, several
factors may influence on the way to tension it (weight of the net, tension system, type of
post,…). We recommend at the first use to tension the net in order that its height on the middle is
2.43m, and to check that the mark on the ruler matches with the height 2.45m (2.26 for women). If it
is not the case, please adjust the position of this mark.

7 7
NECESSARY
ITEMS
4– NET TENSION
Be careful to follow the following assembly sequence
for the capstan :
- Pass the wire through the clam cleat (opposite side of
PVC handle)
- Pass the wire through the pulley
- Tie a knot with the wire on the ‘U’ hook
- To tense the net, you just need to pull the PVC han-
dle
Net wire
SLIDING BAR WITHOUT CAPSTAN SLIDING BAR WITH CAPSTAN
X1
Capstan + stainless
steel ‘S’ hook
X1
Turning knob M10 +
wire D6
ASSEMBLY
Net wire
Fix the wire on the
‘S’ hook
Fix the wire on the
‘U’ hook

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing method Weight (kg) Dim. (mm)
A1 S30158 EPost 1 + 1 Plastic bubbles + cardboard 5
layers 20 3000x240x180
ACCESSORIES PUT IN A CLEAR PVC BAG
Package
N° Designation Description Qty Note
A1 Stainless steel tur-
ning ring M8 + Brack-
et M8 2 + 2 To be fixed on the
sliding bars
A1 SS screws M10x30 + SS washers 10
+ SS locknut M10 2 + 4 + 2 To be fixed on the
sliding bars
A1 Pulleys D30 2To be fixed on the
sliding bars
A1 Sliding bars R&L 1 + 1
A1 Capstan with ‘S’
hook 1
A1 Turning knob M10 +
wire D6, lg 3m 1 + 1 To be fixed on the net
wire
PACKING LIST
ALUMINIUM VOLLEYBALL POST Ø90, CAPSTAN
TENSION
PRODUCT REF S30158 Index E PAIR
PRE-ASSEMBLED ACCESSORIES
Package
N° Designation Description Qty Note
A1 Caps PVC D90 2
A1 Graduated sticker 2
A1 Clamcleat + Self-
tapping screws
M4.8x19 1 + 2
A1 Sticker 1
A1 Conformity sticker 1
VISA PACKING DEPARTMENT DATE: