Sodex Sport S12631 Dimensions

DESCRIPTIF
Alu rectangular tube 20x80
White powder coated
CONFORM
European norm
EN 748
PRODUCT SHEET
FOLDING BASE FRAME FOR
SENIOR GOAL
PRODUCT REF S12631 PAIR
INSTALLATION
The time to make the assembly of these support frame is estimated for 2 persons, at 20 minutes.
MAINTENANCE
The equipment has to be regularly maintained by the owner. It is advised to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
It is advised to carry out this cleaning once or twice a year, or even more regularly according to the environmental
conditions (saline environment, …)
WARRANTY
One full year parts and labour guarantee. Every claim regarding the condition of the delivered equipment has to be
done within the legal period, of the reception of the material.
The warranty will not apply to:
- All degradation during the transport.
- All degradation due to poor maintenance.
- All degradation due to use differing from which was intended
- Any defect claimed after the end of the legal period.
- Any damage due to a faulty installation or assembly of the module
1

2
ASSEMBLY INSTRUCTION
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
NECESSARY
ITEMS
1– POSITIONING OF THE EQUIPMENT (x2)
Allen key 6
x24
SS screws M8x15
IMPORTANT : The net has to be as-
sembled into the support frame BE-
FORE being attached to the goal.
x24
SS washers 10
Put the equipment in position by placing
the part with the groove facing upwards
(see picture below).
x8
Sleeves
x4
Cover

3
NECESSARY
ITEMS
ASSEMBLY INSTRUCTION
2– ASSEMBLY OF THE FOLDING BASE FRAME (x4)
1) Insert sleeves into the external compartments
of the 20x80 profile.
2) Put screws in position , without tightening ( to
keep it loose for the fixation of step 3 )
3) Slide the other part of the profile 20 x 80 on
the sleeves, then put the 2 other
screws. Once the 4 screws are placed, tighten
them.
(Make sure that the gap reduction profile is on
the same side).
x4
SS screws M8x15
x4
SS washers 10
x2
Sleeves

4
NECESSARY
ITEMS
ASSEMBLY INSTRUCTION
3– FIXING THE FOLDING BASE FRAME ON GOAL (x2)
Fix the product to the system on the goal.

5
NECESSARY
ITEMS
ASSEMBLY INSTRUCTION
4- IDENTIFYING THE ANGLES (x2)
6
5
3
4
2
1
D
B
C
A
IMPORTANT : the nets have to be assembled on the
folding base frame BEFORE being fixed on the goal
The ends of the net and of the base frame will respectively by named 1,2,3,4,5,6 and
A,B,C,D for all the rest of the assembly instructions.

6
NECESSARY
ITEMS
ASSEMBLY INSTRUCTION
5– INSERTION OF THE NET IN THE REAR PROFILE(x2)
D
B
C
A
Insert 4 in the C corner and slide it to D.
Advice: Insert the knots one by one in
the corner.
Advice: Be careful that the knots don’t come
out at the junction.

7
NECESSARY
ITEMS
ASSEMBLE INSTRUCTION
6– INSERTING THE NET IN THE SIDE PROFILES (x2)
D
B
C
A
Insert 1 in C corner and slide it to A.
D
B
C
A
Insert 2 in D corner and slide it to B.

8
ASSEMBLY
7– POSITIONING THE COVERS (x4)
NECESSARY
ITEMS
8– LIFTING OF THE BASE FRAME (x4)
Fix the covers leaving the top
corner thread of the net out
through the opening.
To maintain the system in folded position, hang one of the
meshes in one of the hooks located on the goal, or use a
rope.
For lifting, place yourself on the middle rather than on the side.
x4
SS screws M8x15
x4
SS washers 10
x1
Cover

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg) Dim. (mm)
A1 S12631-1BRear 20x80 profiles 2Plastic bubbles + cardboard 5
layers 19 5830x110x80
A2 S12631-21 +
S12631-22 BLeft 20x80 profile + Right 20x80 profile 2 + 2 Plastic bubbles
+ cardboard 5
layers 19 2030x900x140
A3 S12631-9BAccessories
1Plastic bubbles
+ cardboard 5
layers 4380x100x30
PACKING LIST
FOLDING BASE FRAME FOR SENIOR
GOAL
PRODUCT REF S12631 Index B Pair
ACCESSORIES PUT IN A CLEAR PVC BAG
Package
N° Réf Designation Description Quantity Note
A3 BITK0815 +
LITA081815 SS Screw M8x15 + SS washers 8 24 + 24
A3 S12631-3 Sleeves 8
A3 S12631-4 Covers 4
VISA PACKING DEPARTMENT DATE :