Sodex Sport S30061 User manual

1 1
DESCRIPTION
Steel structure D90
Powder coated
CONFORM
European norm
NF EN 1271
ASSEMBLY INSTRUCTIONS
VOLLEYBALL POST ON BASE
PRODUCT REF :S30061 PAIR
ASSEMBLY TIME
The time to make the assembly of this volleyball post is estimated for 1 person, at 20minutes. (without sealing).
MAINTENANCE
The equipement has to be regularly maintained by the owner. It is adviced to:
- Check every week that all the screws are correctly tightened
- Fix paint defects if the module has been damaged, using the adapted paint, specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
It is advised to carry out this cleaning once or twice a year, or even more regularly according to the environmental
conditions (saline environment, …).
WARRANTY
One full year parts and labor guarantee. Every claim regarding condition of the delivered equipment has to be done
within the legal period of the reception of the material. The warranty will not apply to:
- all degradation during the transport.
- all degradation due to use differing from which was intended.
- all degradation due to poor maintenance.
- any defect claimed after the end of the legal period.
- any damaged due to a faulty installation and assembly of the module

2 2
- The distance between the axles of the posts should be 10m minimum and 11m maximum.
We recommend 11m. Nevertheless, please check the length of your cable before choosing
the position of the posts.
- Make the sealing with PJ 45 concrete dosed by 350kg. Let the concrete dry at least 72
hours
Post
IMPLANTATION AND SEALING
Axles
Concrete block
500x500x500mm
Concrete block
500x500x500mm
485 ± 4
A
500
GROUND
Concrete block
500x500x500mm
Post
NB: All the dimensions are given in millimeters.
Important: The distance A is to be de-
termined by the installer. When the
pole is not in use, and the cover is in
place, the top of the pole must be at
ground level

3 3
ASSEMBLY OF THE WINCH
1– PUT OUT THE RACK AND PINION
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
Rack and pinion
Toothed wheelStop
Alu body
Wrench 13mm
Screwdriver
x2
SS Screws M8X25
x1
Crank
x2
SS Washers 8
x1
Screws M5x20
x1
Nut M5
x1
Turn-knob
M6x15
STEP 1 STEP 2
Rack and pinion
NECESSARY
ITEMS
Wrench 8mm
Remove the screw
M5x20, and put the stop
up then take out the rack
and pinion.

4 4
ASSEMBLY OF THE WINCH
2– FIX THE ALUMINIUM BODY TO THE SLIDES AND PUT BACK THE RACK
AND PINION FIX THE LOCK SCREW
NECESSARY
ITEMS
3– ASSEMBLY OF THE CRANK AND PUT THE RANK AND PINION AS HIGH AS
POSSIBLE
NECESSARY
ITEMS
Screw M5x20 +
Nut M5
Turn-knob
M6x15
Crank
x1
Crank
x2
SS Screws M8x25
x2
SS Washers 8
x1
Turn-knob
M6x15
x1
Screw M5x20
x1
Nut M5
SS Screws M8x25 +
SS Washers M8

5 5
ASSEMBLY
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
NECESSARY
ITEMS
1– ASSEMBLY OF THE PULLEYS (X2)
SS Screw M10x35 +
SS washers 10 +
SS Lock nuts M10
Pulley
Tighten the assembly gently to
allow a good pulley rotation
x2
Pulleys
x2
U pieces
Wrench 17mm Wrench 8mm
x1
Pulleys
x2
SS Turn-knob M10
Wrench 19mm
x2
Ground
ancorage
x2
Hook
x4
D90 Wheel
x4
Threaded rod
part BC M12x70
x2
Stainless steel
eye screw
x2
SS Lock nuts M10
SS Screw M10x35
x2 x4
SS Washers 10
SS Screw M10x35
x1 x2
SS Washers 10
x1
SS Lock nuts M10
x2
SS Screw M5x50
x4
SS Washers 6
x2
SS Nuts M5
x8
SS Washers 12
x4
SS Lock nuts M12

6 6
ASSEMBLY
2– ASSEMBLY OF THE SLIDES TO THE POSTS
THE SLIDING BAR WITHOUT WINCH THE SLIDING BAR WITH WINCH
Sliding bar
U Piece
SS Screw M5x50+
SS Washers 6 + SS
Nut M5
Sliding bar
U Piece
The sliders must be situated on the outside of
the court, once the posts are installed
- Fixation the winch on the sliding bar.
- Remove screw M5.
- Put the sliding bar in the rail
- Lock the sliding bar by tighten the turn knob
and U piece
- Put again the screw M5 without tightening it
Tighten the screw M5 loosely, in order not
to damage the rail. This screw acts as a
stopper to prevent the slider from exiting
the rail
NECESSARY
ITEMS
- Remove screw M5.
- Put the sliding bar in the rail
- Lock the sliding bar by tighten the turn knob
and U piece
- Put again the screw M5 without tightening it
The sliders must be situated on the outside
of the court, once the posts are installed
x2
SS Turn-knob M10
Tighten the screw M5 loosely, in order not to
damage the rail. This screw acts as a stopper
to prevent the slider from exiting the rail
x2
U Piece
Ss Screw
M5x50
x2 x4
SS Washers 6
SS Screw M5x50 +
SS Washers 6 +
SS Nut M5
SS Turn-knob M10
x2
SS Nuts M5
SS Turn-knob M10

7 7
3– ADJUST THE HEIGHT OF SLIDING BARS. (X2)
NECESSARY
ITEMS
Turn-knob M10
The red line to determine the height of net
Adhesive
tape
ASSEMBLY
Make sure that the height in the middle of the net is 2.43m when it is stretched for a
male adult competition (2.24m for women). It is recommended to adjust the height at
the ends of the net 2 cm above that desired in the center. However, there are many
factors that can affect the way it is stretched (net weight, tension system, pole type,
etc.). We advise you to stretch the net at the first use, making sure that the height of the net is
2.43m, and check that the mark previously inscribed on the ruler coincides well with 2.45m
(2.26m). m for females) indicated on the label. If this is not the case, please adjust the position of
this mark.
4– ASSEMBLY OF THE WHEEL (X4)
NECESSARY
ITEMS
x1
Threaded rod
part BC M12x70
x1
Wheel D90
Threaded rod part BC M12x70 +
SS Washers 12 + SS Lock nuts M12
x2
SS Washers 12
x1
SS Lock nuts M12

8 8
5– ASSEMBLY OF THE POSTS (X2)
NECESSARY
ITEMS
Hook
ASSEMBLY
x1
Anchorage
x1
Hook
x1
Stainless steel
eye screw
Stainless steel
eye screw

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg)
Dim.
(mm)
A1 S30061-01 +
S30061-09 BPost + Accessories 1
Plastic bubbles
+ cardboard 5
layers
19 2580x530x630
A2 S30061-01 BPost 1
Plastic bubbles
+ cardboard 5
layers
19 2580x530x630
ACCESSORIES IN CLEAR PVC BAG
Package
N° Ref Designation Description Qty Note
A1 KIM10 SS Turn-knobs M10 2Fixation of the slides
A1 BITH1035 +
LITA102220 + TITD10
SS Screw M10x35 +
SS Washers 10 +
SS Lock nuts M10
2+4+2 Fixed the pulleys
A1 PULYN30 Alu pulley D30 2To be fixed on the
slides
A1 Sliding bar L&R 1+1 To slide in the post
A1 S25595B Winch 1To be fixed on the
sliding bar
A1 U piece 2To be fixed on the
sliding bar
A1 BXN09034 Wheel D90 4
Mounted on the base
A1
BTBI1270 +
LITA122620 +
TITD12
Threaded rod part BC
M12x70 + SS Washers 12
+ SS Lock nuts M12
4 + 8 + 4 To assemble the
wheel to the posts
A1 Anchorage 2
To anchor in the
ground
A1 Hook + Stainless steel eye
screw 2 + 2 To fix the post on the ground
A1 Steel cap 2
To cover the anchor
when the post is not
in use
PACKING LIST
VOLLEYBALL POST ON BASE
PRODUCT REF S30061 Index B PAIR

PACKING LIST
VOLLEYBALL POST ON BASE
PRODUCT REF S30061 Index B PAIR
ACCESSOIRES PRE-MONTES
Package
N° Ref Designation Description Qty Note
A1 +
A2 NNT90 PVC D90 Cap 2
A1 +
A2 NN4080 PVC Cap 40x80 4
A1 +
A2
BITH0550 +
LITA061610 + TITC05
SS Screws M5x50 + SS
washers 6 + SS nuts M5 2+4+2
A1 +
A2 TC05 Rubber Platinum 5mm Ø96 + 80x50x5mm 2 + 4
A1 +
A2 NTBC302500 Adhesive tape 2
A1 Label "IMPORTANT" 1
A1 1Label “CONFORMITE”
VISA PACKING DEPARTMENT DATE:

NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg)
Dim.
(mm)
A1 S25595B G
Alu body + Rack and pi-
nion +Toothed wheel +
stop
1 + 1 + 1
+ 1 Clear pvc pag 1.4 500x80x160
ACCESSORIES IN CLEAR PVC BAG
Package
N° Ref Designation Description Qty Note
A1 NVN0615P Turn-knob M6x15 1
A1 S25595BC-03 Crank 1
A1 BITH0825 +
LITA081815
SS Screws M8x25 +
SS Washers 8 2+2
PRE-ASSEMBLED ACCESSORIES
Package
N° Ref Designation Description Qty Note
A1 TRTHEPM Rack and pinion 1
A1 ANHOM2 Alu body 1
A1 Stop 1
A1 BRDM Toothed wheel 1
A1 RVD5010 + OBID4.7 Rivet ø5x12+ ball 2+1
A1 PT20N Circlips D20 1
A1 BTKK0520 + TTKC05 1+1Screw M5x20 + nut M5
VISA PACKING DEPARTMENT DATE:
PACKING LIST
ALU WINCH
PRODUCT REF S25595B Index G UNIT