Sodex Sport S16216 User manual

DESCRIPTION
Steel structure 80x80
Powder coated
3.00m x 2.00m
CONFORM
European Standard
NF EN 749
ASSEMBLY INSTRUCTION
HANDBALL COMPETITION GOAL,
SOCKETED
PRODUCT REF. :S16216 PAIR
ASSEMBLY TIME
The assembly time for this goal is estimated between 30 to 45 minutes at 2 persons (without concreting).
TEST AFTER INSTALLATION
According to the regulation above, this product has to be tested as below:
- Put 180kg at 20cm from the ground and in the middle of the crossbar for 1min.
- Apply an horizontal force of 110 kg on the middle of the crossbar, by a 3 meter rope, for 1min.
After these tests, the equipment and the fixation system should not have a break, move or show residual
deformation.
During the first installation, stability and strength tests are compulsory.
Every time you install the equipment, a visual check of the stability and strength must be realized.
The owner of this equipment must usually control the product.
For an optimal use of our products, we advise to follow the installation and maintenance instructions.
MAINTENANCE
The equipment has to be regularly maintained by the owner. It is recommended to:
- Check every week that all the bolts are correctly tightened.
- Fix paint defects if the unit has been damaged, using the adapted paint specified by the manufacturer.
- Replace all damaged or missing parts with a spare part recommended by the manufacturer.
- Clean the product by using dishwasher soap, clean water, and soft cloth.
WARRANTY
One full year parts and labour guarantee. Every claim regarding the condition of the delivered equipment has to be
done within the warranty period following receipt of the product.
The warranty will not apply to:
- Any degradation during transport.
- Any degradation due to poor maintenance.
- Any degradation due to use differing from which the product was intended.
- Any defect claimed after the end of the warranty period.
- Any damage due to a faulty installation or assembly of the product.

2
NB: All the dimensions are given in millimeters
NECESSARY TOOLS (NOT INCLUDED)
.
Drill Wick concrete D16mm
Mallet
Front rear footing
500x500x500mm
Front rear footing
500x500x500mm
Back rear footing
250x250x250mm Back rear footing
250x250x250mm
POST
80X80
FIXATION AND FOOTING
Concrete block
(chemicals anchor)
500
400
350
- Dig the holes for the footing of the anchors
according to the written dimensions.
- Realize the sealing with concrete CPJ45
dosed by 350 kg and wait at least 72 hours
(6 days during winter).
- Once the concrete is in the hole, put the
anchor’s tubes.
- Drill the holes for the chemicals fixings by
using a concrete drill diameter 16 mm. Do not
drill a hole more than 80mm.

3
ASSEMBLY
NECESSARY
ITEMS
1– ASSEMBLY OF THE POSTS TO THE CROSSBAR (x2)
CROSSBAR
POST
CROSSBAR
POST
NECESSARY TOOLS (NOT INCLUDED)
INCLUDED ITEMS
x12
Rubber supports
Wrench 17mm
x4
Lifting ring
M12x40
x4
Chemical fixing
M12x50
SS Screws
M10x30
x24 x4
SS Locknut M10
x32
SS Washers 10
x4
SS Screws
M10x60

4
ASSEMBLY
NECESSARY
ITEMS
2– ASSEMBLY OF THE ARCHES TO THE FRAME (x4)
3– ASSEMBLY OF THE CONNECTION BAR (x4)
STEP 2
STEP 1
POST
SS Screws M10x30
+ SS Washers 10
SS Screws M10x30
+ SS Washers 10
POST
SS Screws
M10x30
x6 x6
SS Washers 10
NECESSARY
ITEMS
CONNECTION BAR
ARCH
x1
SS Locknut M10
x2
SS Washers 10
x1
SS Screws
M10x60
SS Screw M10x60
+ SS Washers 10
+ SS Locknut M10

5
ASSEMBLY
POST
SOCKET
NECESSARY
ITEMS
x3
Rubber supports
x1
Lifting ring
M12x40
x1
Chemical fixing
M12x50
4– FIXATION OF THE GOAL (x4)
Rubber supports
Chemical fixing
M12x50
Lifting ring
M12x40
JOINING BAR

PACKING LIST
HANDBALL COMPETITION GOAL,
SOCKETED
PRODUCT REF S16216 Index G PAIR
NOMENCLATURE
Package
N° Ref Index Designation Description Quantity Packing Method Weight (kg)
Dim.
(mm)
A1 S16211-01 DCrossbar 2
Plastic bubbles
+ cardboard 5
layers
40 3200x200x400
A2 S16216-02 DPost 2
Plastic bubbles
+ cardboard 5
layers
23.2 2180x200x100
A3 S16216-02 DPost 2
Plastic bubbles
+ cardboard 5
layers
23.2 2180x200x100
A4 S16320-03 CR&L arch 2
Plastic bubbles
+ cardboard 2
layers
17 2100x1160x220
A5 S16320-03 CR&L arch 2
Plastic bubbles
+ cardboard 2
layers
17 2100x1160x220
A6 S16320-05 AConnection bars 2
Plastic bubbles
+ cardboard 2
layers
11 3080x100x100
A7 S16216-09 GAccessories 1Cardboard 2
layers 2350x160x100
ACCESSORIES PUT IN A CLEAR PVC BAG
Package
N° Ref Designation Description Qty Note
A7 BITH1030 +
LITA102220 +
SS Screws M10x30 +
SS washers 10 24 + 24 Assembly of the crossbar to the posts
A7
BITH1060 +
LITA102220 +
TITD10
SS Screws M10x60 +
SS washers 10 +
SS locknuts M10
4 + 8 + 4 Fixation of joining bar
A7 GCCV30 Rubber supports 12 Assembly under arch
and joining bar
A7 TKD1250 +
S16340EZ
Chemical anchors M12x50
+ lifting rings M12x40 4 + 4 Goal anchoring
PRE-ASSEMBLED ACCESSORIES
Package
N° Ref Designation Description Qty Note
A1-A5 S12363 + VITF4819 Hooks 1 fixation + self-
tapping screws M4.8x19 54 + 54 Fixed on front frame
and arch
A2 Conformity stickers 2
VISA PACKING DEPARTMENT DATE :