Sol-Expert group Willi User manual

Firmenanschrift aufbewahren -
Keep the address of the company -
Veuillez conserver l'adresse -
Adres bewaren -
Nicht geeignet für Kinder unter 3 Jahren! - Verschluckbare
Kleinteile! Not suitable for children under 3 years! -
Contains small parts! Ne convient pas pour les enfants de moins
de trois ans! - Contient de petites pièces pouvant être absorbées! Niet
geschikt voor kinderen beneden 3 jaar! - Kleine onderdelen Kunnen worden ingeslikt!
Tel.: [phone] - 94115-0 - Fax: [phone]
[email protected] - www.sol-expert-group.de
SOL-EXPERT group, C.Repky - Mehlisstrasse 19 - D-88255 Baindt
No. 76332
MADE IN EUROPE
SOL-EXPERT
group
group
10+
Return the device to a
certified provider at the
end of its useful life!
4 0 3 7 3 7 3 7 6 3 3 2 0
Preparation:
Carefully release wooden parts from the board
and set out all parts.
! !
Safety notes:
Keep this manual for future reference! It contains important information.
When the battery is drained, always replace it with a new battery with the same rating.
The soldering iron, solder and the parts being soldered become very hot. Be very careful!
Always use a mat when soldering! This prevents parts from slipping.
We recommend using a soldering iron holder to set the soldering iron down safely during use.
This kit is intended for battery operation only.
Environmental notes:
Generally: Please return the electronics to a certified provider at the end of their useful life. These will then ensure the parts are
disposed of in compliance with directives. This is good for the environment and an important part of actively protecting the
environment.
Battery ordinance:
You have purchased a battery-powered product. The battery has a limited life and must therefore be replaced regularly. Do not
dispose of used batteries in the household waste. Consumers are required by law to return batteries to a suitable collection point.
Used batteries contain valuable raw materials which are recyclable. You can also send your used batteries to us: SOL-EXPERT
group, Mehlisstrasse 19, 88225 Baindt.
Soldering kit "Willi the Ghoulish Ghost"
Generally: This soldering kit is intended to introduce to the basics of soldering. It is excellent for instructor-led courses at schools
and workshops. Willi the Ghost can also be used at holiday programmes, school camps and other events related to soldering.
Dimension ghost "Willi": 105 x 82 x 28 mm (H x W x D).
Functionality
The completed kit can be used as a night light. The battery can be replaced with a battery of the same type.
You will also need:
Soldering iron, solder, tweezers, wire strippers
ATTENTION: Never connect the kit to 230 V mains voltage! Acute danger to life!
„Willi" the Ghost Soldering Kit
00 12345678
Cable and LED template for step
and .
8 cm8 mm
B H
Recommendation for children
and teenagers: Assembly and
soldering should be supervised
by an adult.
Anleitung (DT) Manual (EN)
Instructions (FR) Instructies (NL)
https://www.sol-expert-
group.de/76332_Anleitung_Ge
spenst%20Willi-DT(4).pdf
https://www.sol-expert-
group.de/76332_Anleitung_Ge
spenst%20%20Willi-EN(2).pdf
https://www.sol-expert-
group.de/76332_Anleitung_Ge
spenst%20Willi-FR(2).pdf
https://www.sol-expert-
group.de/76332_Anleitung_Ge
spenst%20Willi-NL(2).pdf
QR Codes:
Conrad No.
1818583

Assemble the ghost: - - - - - 612345
A
ASSEMBLY INSTRUCTIONS
1
2
6
4
5
3
Push the eyes and lantern
into the ghost.
Solder point
And now the:
BTrim one end of the resistors with wire cutters:
Trim the post of the LEDs with side cutters:SHORT
2 x
1 x
approx. 8 mm
approx. 8 mm
approx. 8 mm
2.2 kOhm
1 kOhm
short = „-“
long = „+“ long = „+“
before
after
NOTE:
The post of the orange LED
is red! Do not reverse.
brown-black-black-brown-black
red-red-black-brown-black
CSolder LEDs and resistors together.
(pre-tin the indiviual wires)
ATTENTION! Pay attention to the correct resistance!
The ring colours indicate the resistance.
2,2 kOhm
2.2 kOhm for red
1 kOhm
1 kOhm for orange
LED,
(lantern LED)
orange LED 2 x LED, red LED
(eye LED)
Solder point Solder point
brown-black-black-brown-black red-red-black-brown-black
Result:
HOT!!
D
E
FPlace the 3 positive contacts for the LED on top of
each other as shown and solder:
Solder point
Trim the excess wire for
the positive contacts
and solder on the last
resistor as shown.
G
Solder point
Trim
Now trim the cables for the battery clip to 8 cm
(use template), strip the insulation,
pre-tin and solder as shown:
Solder
point
Checked everything and found no
short-circuit?
Then you can connect the battery.
All LEDs should now light up and
flicker like a candle
Changes and errors reserved - July 2018 / Christian Repky ©
I
H
To switch off the LEDs simply
disconnect the battery clip.
ATTENTION!
The wires soldered to the resistors
must not touch the wires for the
positive contacts. This would cause
a short-circuit, damaging the battery!
brown-black-black-brown-black
((Use template from page 1)
Push the eye LEDs into the wooden piece as shown,
and
then solder.
bend the feet with resistors
Wood Wood
wrong! right!
Note the
resistor
position!
LED LED