Solar Light-N-Carry LNC1541 User manual

COB LED Rechargeable Work Light
Operator’s Manual
Model Nos. LNC1241, LNC1341, LNC1541
WARNING
Read these instructions completely before using the Jump-N-Carry and save them for
future reference. Before using the Jump-N-Carry to jump start a car, truck, boat or to
power any equipment, read these instructions and the instruction manual/safety
information provided by the car, truck, boat or equipment manufacturer. Following all
manufacturers’ instructions and safety procedures will reduce the risk of accident.
Working around lead-acid batteries may be dangerous. Lead-acid batteries release
explosive gases during normal operation, charging and jump starting. Carefully read and
follow these instructions for safe use. Always follow the specific instructions in this
manual and on the Jump-N-Carry each time you jump start using the Jump-N-Carry.
All lead-acid batteries (car, truck and boat) produce hydrogen gas which may violently
explode in the presence of fire or sparks. Do not smoke, use matches or a cigarette
lighter while near batteries. Do not handle the battery while wearing vinyl clothing
because static electricity sparks are generated when vinyl clothing is rubbed. Review all
cautionary material on the Jump-N-Carry and in the engine compartment.
Always wear eye protection, appropriate protective clothing and other safety equipment
when working near lead-acid batteries. Do not touch eyes while working on or around
lead-acid batteries.
Always store clamps in their holsters, away from each other or common conductors.
Improper storage of clamps may cause the clamps to come in contact with each other,
or a common conductor, causing the battery to short circuit and generate high enough
heat to ignite most materials.
Use extreme care while working within the engine compartment, because moving parts
may cause severe injury. Read and follow all safety instructions published in the vehicle's
Owner's Manual.
While the battery in the Jump-N-Carry is a sealed unit with no free liquid acid, batteries
being jump started with the Jump-N-Carry unit likely contain liquid acids which are
hazardous if spilled.
Failure to follow instructions may
cause damage or explosion,
always shield eyes. Read entire
instruction manual before use.
WARNING

2
PLEASE SAVE THIS OWNERS MANUAL
AND READ BEFORE EACH USE.
This manual will explain how to use the work light safely and
effectively. Please read and follow these instructions and pre-
cautions carefully.
This unit has a sealed lithium battery that should be kept at full
charge. Recharge when first received, immediately after each
use, and every six months if not used. Failure to perform
maintenance charges may cause the battery life to be reduced
greatly.
Read these instructions completely before using the
Light-N-Carry and save them for future reference. Be-
fore using the Light-N-Carry to jump start a car, truck,
boat or to power any equipment, read these instruc-
tions and the instruction manual/safety information
provided by the car, truck, boat or equipment manu-
facturer. Following all manufacturers’ instructions and
safety procedures will reduce the risk of accident.
Always wear eye protection, appropriate protective
clothing and other safety equipment when working
on vehicles or other equipment.
Use extreme care while working within the engine
compartment, because moving parts may cause
severe injury. Read and follow all safety instructions
published in the vehicle’s Owner’s Manual .

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS – This manual contains
important safety and operating instructions for Model Nos.
LNC1241, LNC1341 and LNC1541. Read, understand and
follow all instructions, cautions and warnings listed in this
manual. Failure to follow all instructions could result in per-
sonal injury, injury to others and property damage.
IMPORTANT! – Charge work light immediately after
purchase, after each use, and at least every 3 months
when not in use.
DO NOT turn on the work light while it is being charged.
DO NOT handle or move the work light while it is being
charged.
DO NOT look directly into the light or shine the light directly
into the eyes of any person or animal.
DO NOT allow children to use the work light.
DO NOT operate the work light if it has received a sharp
blow, been dropped, or otherwise damaged in any way; take
it to a qualied service person.
DO NOT allow the unit’s battery to stay in a discharged state
for long periods of time. This has a detrimental effect on
battery life.
AC CHARGER FOR INDOOR USE ONLY. DO NOT expose
the charger to water or use in damp conditions.
WARNING! Do not use any other charger except the one
provided to charge the work light. Use of a charger not sup-

4
plied by the manufacturer may result in a risk of re, injury to
persons and/or damage to property.
DO NOT use the work light with a charger which has a dam-
aged cord or plug. Replace the cord or plug immediately.
To reduce the risk of damage to the charger plug, pull by the
plug, rather than the cord, when disconnecting the charger.
DO NOT use the provided charger to charge or power any
other electrical item.
PERSONAL SAFETY PRECAUTIONS
DO NOT disassemble the work light; take it to a qualied
service person when service or repair is required. Incorrect
reassembly may result in a risk of re.
DO NOT expose to temperatures above 140˚F (60˚C).
Recycle or dispose of the used battery as required by local
regulations.
FEATURES
- ON/OFF Power Button
- COB LED Work Light with 2 Settings
- SMD LED Focus Beam light
- MicroUSB Charging Port
- State of Charge / Charging Status LED Indicator
- Magnet
- Hook
- USB/Micro USB Charging Cord
- AC Wall Charger with USB Port

5
CHARGING
NOTE: CHARGE THE WORK LIGHT IMMEDIATELY AFTER
PURCHASE, AFTER EACH USE, AND AT LEAST EVERY 3
MONTHS WHEN NOT IN USE. Failure to do this will reduce
the battery’s useful life.
Connect the microUSB end of the charging cable to the
microUSB port on the work light. Connect the USB end of the
charging cable to the USB port of the AC charger. Plug the
AC charger into a functioning AC outlet.
The blue state of charge / charging status LEDs will blink
in succession to indicate charging progress. To reach full
charge, continue charging until all four LEDs are lit solid.
Charging will take approximately 4 hours, depending on the
unit’s state of charge at the start of the cycle.
The charging process is fully automatic and the light can
remain connected to the charger indenitely without adverse
consequences.

6
OPERATING INSTRUCTIONS
Do not turn on the work light while it is being charged.
Direct the lens away from your eyes before turning on the
work light.
Press the POWER button to achieve the operational mode
desired:
– Press POWER for COB Work Light low brightness mode.
– Press POWER a second time for COB Work Light high
brightness mode.
– Press POWER a third time for Focus Beam Light mode.
– Press POWER a fourth time to turn the unit OFF.
The unit incorporates a rotating arm with an integrated mag-
net in its base for ideal positioning, allowing it to be attached
to any ferrous metal surface. The unit incorporates a hook to
allow it to be hung for ideal positioning.
Recharge the work light after use, and at least every 3
months when not is use.
MAINTENANCE INSTRUCTIONS
After use and before performing maintenance, disconnect
the work light from the charger.
Use a dry cloth to wipe any dirt or oil from the charger, cord
and light.
Any servicing should be performed by qualied service
personnel.

STORAGE INSTRUCTIONS
Store inside, in a cool, dry place.
Take care to avoid/prevent damage to the charger, cord
and unit. Failure to do so could result in personal injury or
property damage.
Charge the work light’s internal battery immediately after
purchase, after use and every 3 months when not in use.
All batteries are affected by temperature. The ideal storage
temperature is 70˚F. The internal battery will gradually
self-discharge (lose power) over time, especially in warm
environments. Leaving the battery in a discharged state
may result in shorter than expected battery life.
REPLACEMENT PARTS
Charger replacement kit (includes wall charger and
USB/microUSB cable) – PART NO. LNC215
Learn more about work lights on our website.