Soleus Air Thrive SF005 User manual

Thrive Activity Tracker – SF005
Thrive Activity Tracker
SF005
Introduction
Thank you for purchasing the Thrive activity band using OLED display. This product uses an
electro-optical cell to sense the volume of blood under your skin.
This device can also record your Exercise time, Steps, Distance, Calorie, etc. It has a Sleep
function that will track your total sleep time, deep sleep and light sleep. It also has a Find phone
function (when connected via Bluetooth).
WARNING:
•Consult your doctor before you begin a new exercise program. This is important for persons
with pre-existing health problems or persons who have taking medication regularly.
•This watch provides heart rate measurements. However, this is not a medical device.
•This watch may affect pacemakers. If you have any concerns, consult your doctor before
using this watch.
•Over exercising may result in serious injury or death. If you feel faint, if you become short of
breath, or if you experience pain while doing an exercise, stop immediately and cool down.
Charging battery to Computer
Charge the unit for at least 3-4 hours before first use. The length of time for a fully charged battery
will last depending on the actual usage.
•Plug your USB cable to your computer.
•Align the charging clip with the contacts on the back of your device.
•Connect the charging clip securely to the device.
Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper
electrical contact and prevent corrosion.
How to wear the device properly in your forearm:
•Fasten the device snugly so that the optical sensor makes a tight contact with your skin.
The tighter you can wear the watch the better.
•Wear the device not on your wrist bone but higher on your forearm.
•If the Heart rate data displayed in the watch is not stable or erratic, try to move the device
along your forearm within the best wearing position as shown.
Important notes:
Before starting your exercise
•You may need to tighten the strap
** After sweating, you have to tighten the device again for more accurate measurement.
•Make sure the heart rate reading is already stable.
•Minimize extreme wrist movement while the HR is in use.

Thrive Activity Tracker – SF005
Pairing your device with Smartphone:
•Press and hold S1 button from any of the Time screen or OFF screen until the pairing screen
appears (PAIR 1550).
•Then open your Soleus App to pair.
Notes:
!If pairing is successful, the “PAIR OK” will be displayed.
!If pairing is not successful, after 1 minute, the “PAIR X” will be displayed.
!While in pairing screen, User has an option to cancel the pairing process by pressing
the S1 button.
!While in OFF screen or in any Time screen, press and hold S1 button to turn off the
Bluetooth.
Knowing the Thrive modes:
•Press S1 button to scroll the main modes; TIME, HRM, WORKOUT, SLEEP, FOOD IN
(food intake), and FIND PHONE.
HRM mode
•Press S1 button until you reach in HRM mode, it will then auto search the HRM signal. Once
HRM signal is received, it will automatically show your heart rate.

Thrive Activity Tracker – SF005
WORKOUT mode
•Press S1 button until you reach in WORKOUT mode.
•Press and hold S1 button until “HOLD TO START”appears to start your exercise (the human
logo will start moving and the exercise timer will also start counting).
•Press and hold S1 button to stop your activity and wait until “HOLD TO STOP” appears.
•Press and hold S1 button to save your current data and wait until “HOLD TO SAVE” appears
then followed by “SAVED” screen.
Notes:
!While the exercise timer is running or stop or save, the workout views will auto scroll.
!There’s no restart function.
!When you go to SLEEP mode while the Exercise is ON or active, it will display “EXER IS
ON”.
!Once you reach your target goal (Steps, Calorie, Distance), the wearable band will
display “CONGRATS!”
SLEEP mode
This device will track the following information about your sleep: Total Sleep time, Deep Sleep and
Light Sleep.
This function can be set either “MANUAL” or “AUTO” on your Smartphone App.
Manual setting:
•Press S1 button until you reach in SLEEP mode. And seconds later, it will be display “TO BED”.
•Press and hold S1 button to start your bed time until “HOLD TO START” will appear. The sleep
logo will also be displayed to indicate your band is in sleep mode.
Or when you “WAKE-UP” in the morning, press and hold S1 button until “HOLD TO STOP” will
appear. It will then auto displayed the Wake up logo, Total sleep time, Deep sleep and Light
sleep.

Thrive Activity Tracker – SF005
Auto setting:
•Your Smart band will wish you “GOOD NIGHT” and “GOOD MORNING” that will automatically
display based on the preset Sleep Time on your Smartphone App.
Note: When you go to WORKOUT mode while the SLEEP is ON or active, it will display “SLEEP
IS ON”.
FIND PHONE mode
This function helps locate your Smartphone that is paired via Bluetooth 4.0 technology.
To find your device, the Smartphone App must be open in the background.
•Press S1 button until you reach in FIND PHONE mode. The find phone logo will be displayed.
•Press and hold S1 button and the device will display “HOLD TO FIND PHONE” followed with
blinking phone logo. It will then auto search and you will notice an audible alert on your mobile
phone.
•Press S1 button to stop the audible alert.
Text Message and Phone Call Notifications
When paired with a compatible Apple or Android Smartphone, the wearable band will alert you of
incoming texts and phone calls. Caller ID is limited to 32 characters and text message content is
32 characters.
Receiving an Incoming call:
•In any screen, when receive an incoming call, the device will show the Caller ID (phone number
or name). It will also scroll with vibration (optional).
•Press S1 button to exit.
Receiving a Message:
•In any screen, when receive a message, the device will show the Sender’s name/message or
Sender’s phone number/message. It will scroll with vibration (optional).
•Press S1 button to exit.

Thrive Activity Tracker – SF005
Data Memory
Exercise data: 10 files
Daily data: 7 days
Sleep data: 7 files
Note that when Memory is full, Memory is managed in First in – First out basis. The oldest file will
be automatically deleted and replaced by the newest file.
Battery Charge
The device is powered by a built-in lithium-ion battery. It can be charged using the USB port and it
takes approx. 3.0 hours to fully charge the battery. Please charge the device before using and
never let it reach 0%.
Press S1 button from OFF screen to show the battery level during charging period.
Battery Life
Battery power will last for 7 days typ. on a single charge. But this will vary depending on
Customer’s usage.
Battery Replacement
The battery on this device is not User replaceable and it is highly recommended by an authorized
service personnel only.
Size and Weight
Device size (W x T): approx.17.6 x 8.0 mm.
Device weight: approx. 25.0 grams
Water Resistance
This device is an IPX7 standard.
Troubleshooting Guide:
•If the Heart rate data displayed in the device is not stable or erratic, try to move the
device along your forearm within the best wearing position as illustrated in page 1.
•Fasten the device snugly so that the optical sensor makes a tight contact with your skin.
The tighter you can wear the device the better.
•Your skin should be no SCARS or any other object in your skin that will interfere with the
sensor.
•The heart rate is taken directly through your skin to the device sensor, so it is very
important that there are no obstructions that will interfere with the detection of the Heart
rate.
•Try to wear the device on your other wrist.