SOLIS WL Stick Operating and maintenance instructions

WL Stick Datalogger
Quick Installation Manual
Version: 1.2
1 Quick Installation Manual
1 WL stick
Delivery Content

Install
1
1.1 Install the network cable
Step1: Remove the “Plastic Nut”, “Thread Clamp
Claw”, and “Sealing Ring” in turn.
Step2: Pass the network cable plug through the
“Plastic Nut”, “Thread Clamp Claw”, and “Sealing
Ring” (with opening) in the direction as shownin the
figure below.
Step3: Fully embed the “Sealing Ring” into the
“Thread Clamp Claw”.
Step4: Connect the “RJ45 Plug” to the datalogger
and tighten the “Plastic Nut”.
To router
Plastic
Nut
Thread
Clamp Claw
Sealing
Ring
RJ45
Plug
Ethernet Port
Due to limited space, only RJ45 plug without
protective shell can be used.
NOTE
The diameter of the network cable connection end
on the data logger is about 3.5mm after it is
completely fastened. The network cable is
required to be circular or oval, and the diameter of
the network cable needs to be greater than 4mm in
order to be properly sealed.
Protection cap

Connect the datalogger to the corresponding 4-pin
COM port of the inverter. A Solis 5K inverter is used
here as an example.
Please follow the instructions below:
Match the joint
1.2 Install the datalogger
Install the datalogger:
Step 1: Match the joint, and then insert the
datalogger to the inverter COM port.
Step 2:Rotate the black ring in clockwise.
Only rotate the black ring at the connection end,
not rotate the main body.
NOTE
2
1

If you need to collect data from multiple inverters,
please follow the inverter user manual to establish a
communication connection with the inverter using
the RS485 communication cable in a "hand in hand"
manner.
After the datalogger is installed on the inverter, if the
inverter is powered on, you need to set the inverter
slave address, the default slave address of the
inverter is 01, and each inverter on the communica-
tion circuit needs to be assigned with different slave
address different slave address(like 01, 02, 03, 04...).
NOTE
The device must be installed away from the strong
magnetic field produced by large electrical
appliances such as microwave oven, refrigerator,
telephone, metal walls, etc. Otherwise, the
communication quality may be affected. It may
also be affected by lighting storm.
1.3 Install with multiple inverters
Hand in hand connection of multiple inverters
RS485 RS485 RS485
... ...
COM
Inverter 1 Inverter 2 Inverter n
≈

LED
indicators Description LED
Status Meanings
Trying to connect
with server
Trying to connect
with inverter
Successfully
connected
Successfully
connected
Datalogger is
powered up
normally
Abnormal
connection
Abnormal
connection
Datalogger is
powered up
abnormally
Flashing
Flashing
ON
ON
ON
OFF
OFF
OFF
Shows the
connection
status between
the datalogger
and the server.
Shows the
connection
status between
datalogger and
the inverter.
Shows the
power supply
status of the
datalogger.
LED Lights Status:
Internet
Indicators
(NET)
Inverter COM
Indicators
Power
Indicator
(COM)
(PWR)
The button on the front is used for [RESET]
connection.
·Short press will send the data immediately.
·Long press for over 10 seconds until only the red
light is on will reset the connection.
The three constantly ON LED lights indicate the
datalogger is working normally.
Button Instruction:
LED and Button
2

LAN Configuration
3
3
After the datalogger is connected to the router
through the network cable,LAN Configuration is
completed.
NOTE
WL Stick automatically obtains IP by default and
and connects to the network. If the datalogger fails
to connect to the network, please perform the
following steps to set the IP address. Otherwise,
skip the following steps.
Step 1: The wireless device(mobile phone or laptop)
connects to the datalogger hotspot(Solis_serial
number). The default password is 123456789.

Step 2: Enter in the web browser, 10.10.100.254
open the following configuration interface.
Enter Username and Password .Admin 123456789
Save
Step 3: Select the “ ”and “ ”. WAN port setting Static IP
Enter IP address, Subnet mask, Gateway address,
DNS server address for network cable. Then click
“ ” .Save
Step 4: The following interface pops up to indicate
that the setting is successful. Otherwise please try
LAN configuration again.

Step 1: Use you phone to scan the QR code to
download and register the Solis Cloud APP. Or
directly download from APP Store or Google Play
Store by searching "Solis Cloud”.
Step 2: If it is a new datalogger, please configure it
first, then click the “ ”.WiFi Configuration
Unlogged account, click on "More Tools" and select "WiFi Configuration”
More Tools
If you have logged in, please click "Tool" to enter "WiFi Configuration”
Tool
Solis Cloud
WiFi Configuration
4 4

Step 4: Choose the configuration method,
recommended click " ".Browser Configuration
Step 3: Manually input datalogger SN or Scan the
SN on the datalogger.
Input datalogger SN

Step 5: Make sure that the green light flashes at
intervals,then click the " ".I'm sure it is flashing

Step 6: Connect to the datalogger hotspot
(Solis_serial number).
Step 7: The default password is .123456789
After that, return to APP.

Step 8: Click “ ”, make sure the phone is connected
to router WiFi and switch back to the page to fill in
the WiFi password, then move to next step.
Step 9: Configuration Complete.

Change the Password
5
5
For security reasons, you are advised to change the
password of the datalogger hotspot,which is also the
login password of the website . 10.10.100.254
Step 1: The wireless device(mobile phone or laptop)
connects to the datalogger hotspot(Solis_serial
number). The default password is .123456789
Step 2: Enter in the web browser 10.10.100.254
when the router is not connected, open the following
configuration interface.
Enter Username and Password . admin 123456789
Step 3: Select the " ",enter the new Advanced
password and then click the " ".Save

Step2: Select Owner or Organization for email
address registration.
Create the Solis Cloud Account
6
6
Step 1: Click the “ ”.Register
Register

Step3: Enter the email to get the verification code,
than enter your account and password, last click the
" ".Register
Owner Register
Register

Organization Register

Create Plant
Step1: Enter the main page of Solis Cloud APP, click
“ ”at the top right corner and select " " .+ Add plant
7
7
Add plant

Step 2: Input the information of the plant as required.
Then click " ".Done
Done

Step 3: Confirm the plant information.
Click " ".Create plant
Step 4: Click “ ” to enter the plant View plant
homepage , then add the datalogger.
View plant
Add
(UTC-12:00) Sun Line West
Create plant
Plant Address Ningbo Ginlong
Technologies Co.,Ltd.

Scandatalogger SN Barcode
Can’t find barcode?
Manual
input
Step 5: Scan the SN number of the datalogger or
manually input it.
√×
Note: Scan the , NOT the .datalogger SN inverter SN