SOLIS 1100 User manual

Quick Start Guide
Follow these guidelines when Using SOLIS
Read the User Manual Before Starng
Relieves Pain in Minutes
Manufactured for:
Mid-America Medical Innovaons, LLC
Jeerson City, MO
By Interplex Medical, LLC
Rev. August 2020
Made in the USA

SOLIS PAIN RELIEF SYSTEM
Model 1100 QUICK START GUIDE
Follow these guidelines for proper use of Solis.
Read the User Manual before starng.
Your new Solis is shipped with a fresh 9 Volt
Duracell Alkaline Battery installed. BEFORE USING,
open the battery compartment by sliding the latch
with fingers and remove the plastic insulating tab.
TO REPLACE A USED BATTERY, open the battery
compartment and remove used battery. Check
for proper polarity before inserting new Duracell
battery. Close battery compartment.
Step 1
-- Getting Started... Remove Tab on Battery
Step 2
-- Description of Controls
Start Settings:
▪Intensity Dial at “0”
▪Power Switch to “ON”
▪Polarity to “Normal”
▪Pulse Width to “150”
Step 3 -- Get Acquainted with
the Feel of Therapy
Step 4 –Locate the exact
Pain Area
Moisten the palm of the hand with clean tap water
using a moist towel. Place the device on the palm of
the hand and slowly increase intensity from “0” to the
highest comfortable setting. Tingling or vibration
sensation is normal. Repeat this step with Pulse Width
set at 230. Higher settings decrease treatment time.
Locate the most sensitive pain point
by pressing around the pain area until the most
painful point is found. For larger pain areas see step 7.
Step 5 -- Moisten Skin or
apply Gel
Moisten the skin in the area of pain with clean tap
water using a moist towel. (Water alone provides
good conduction for most users.) If better conduction
is needed, apply a small amount of “Spectra 360 Gel”.
Place the device over the most sensitive pain area. Set
the intensity to “0” and choose the pulse width. Turn
the power on and slowly increase the intensity to the
highest comfortable setting. Press and hold as shown
for 2-4 minutes or as needed to relieve pain.
Step 6 -- Apply Therapy
to Pain
Your new Solis is shipped with a fresh 9 Volt
Duracell Alkaline Battery installed. BEFORE USING,
open the battery compartment by sliding the latch
with fingers and remove the plastic insulating tab.
TO REPLACE A USED BATTERY, open the battery
compartment and remove used battery. Check
for proper polarity before inserting new Duracell
battery. Close battery compartment.
Step 1-- Getting Started... Remove Tab on Battery
Step 2 -- Description of Controls
Start Settings:
▪Intensity Dial at “0”
▪Power Switch to “ON”
▪Polarity to “Normal”
▪Pulse Width to “150”
Step 3 --
Get Acquainted
with
the Feel of Therapy
Step 4 –
Locate the exact
Pain Area
Moisten the palm of the hand with clean tap water
using a moist towel. Place the device on the palm of
the hand and slowly increase intensity from “0” to the
highest comfortable setting. Tingling or vibration
sensation is normal. Repeat this step with Pulse Width
set at 230. Higher settings decrease treatment time.
Locate the most sensitive pain point
by pressing around the pain area until the most
painful point is found. For larger pain areas see step 7.
Step 5 --
Moisten Skin or
apply Gel
Moisten the skin in the area of pain with clean tap
water using a moist towel. (Water alone provides
good conduction for most users.) If better conduction
is needed, apply a small amount of “Spectra 360 Gel”.
Place the device over the most sensitive pain area. Set
the intensity to “0” and choose the pulse width. Turn
the power on and slowly increase the intensity to the
highest comfortable setting. Press and hold as shown
for 2-4 minutes or as needed to relieve pain.
Step 6 --
Apply Therapy
to Pain
Manufactured by Interplex Medical for
Mid-America Medical Innovations, LLC
Jefferson City, MO Rev. August 2020
Step 7 --
Applying Therapy to Larger Pain Areas
A - If the pain area is larger than ¾ inch, repeat Step
6 by positioning the device to the left and to the right
of the original position. Be sure to reduce the intensity
to “0” when changing positions.
Note: Position 1 is the original position. Position 2 is
roughly ¾ inch to the left.
B- Continue to change positions across the pain area
to provide therapy to the entire area. Do not exceed 30
minutes overall treatment time in one session.
Note: Position 2 is roughly ¾ inch to the left of the
original position. Position 3 is roughly ¾ inch to the
right.
Helpful Hints:
The treatment time varies with the level of pain and will vary from person to person.
Always press while holding and do not set the Intensity higher than is comfortable for you. Higher Intensity levels
will normally shorten treatment time but comfort during treatment is highly important.
Once you use the device a few times, you will quickly get acquainted with the best methods and treatment times
for best results.