soloprotect ID User manual

Quick Start Guide

Function:
Keeps the SoloProtect ID baery fully charged.
How to use:
Insert the SoloProtect ID charger lead into the indicated Micro USB
socket. The baery symbol and LED will start to flash. When fully
charged the baery symbol will show full and the LED will display a
constant green light.
• Minimum two hours charging required to reach full charge.
• Placing on charge will disable funcons on the unit.
1Charging
Quick Start Guide

Function:
Turns the SoloProtect ID On or Off.
How to use:
Press highlighted buons simultaneously unl you feel a vibraon.
On – You will feel one vibraon and the SoloProtect ID will then go
through a symbol, light, vibrate and tone sequence.
Off – You will feel two vibraons.
• The device is switched on when removed from charge.
• When turned on, SoloProtect ID will aempt to obtain a
Geolocaon fix as part of the boot-up sequence. See secon 8 for
more informaon.
2Turning On/Off
Quick Start Guide

Function:
Check network coverage and baery strength before working alone.
How to use:
Press the highlighted buon for two seconds to iniate a ‘Device Check’.
The LED lights and display symbols will flash red before seling on green,
amber or red to indicate network coverage and baery strength (can take
up to 20 seconds).
Once complete, the device will obtain a Geolocaon fix denoted by a
symbol on the display, and blue, flashing LEDs. See secon 8 for more
informaon.
• Do not rely on SoloProtect ID if either baery or signal displays red.
3Device Check
Quick Start Guide

4Amber Alert
Quick Start Guide
Function:
Use ‘Amber Alert’ to pre-record details of your locaon and/or to iniate
an amber mer*.
How to use:
Press the highlighted buon unl you feel three short vibraons. When
the LED lights and display starts to flash, you should commence
recording. The display will go solid amber informing you only ten
seconds recording me is remaining before the call is ended.
* Amber mer is not a standard set up opon.

5Red Alert
Quick Start Guide
Function:
Use ‘Red Alert’ any me you feel your personal safety is being
compromised*.
How to use:
Press the highlighted buon for two seconds unl you feel three short
vibraons and the alert symbol is shown. This will mean the ‘Red Alert’
has been acvated and the call is connected. To cancel a ‘Red Alert’,
advise the Alarm Receiving Centre you are safe before pressing the
buon again unl you feel two longer vibraons.
* Check with your employer regarding the exact set up of ‘Red Alert’.

6Incapacitation Alarm
Quick Start Guide
Function:
Incapacitaon detecon is used to raise an alert if you have fallen or
collapsed* - SoloProtect ID’s two-way audio allows an operator to talk
directly to a user.
How to use:
SoloProtect ID will detect an Incapacitaon scenario and go through a
pre-alert phase. Moving the SoloProtect ID cancels this. If the pre-alert
isn’t cancelled then an Incapacitaon ‘Red Alert’ is raised.
• Don’t leave unit on and unaended as this may raise a false acvaon.
*Check with your employer whether this feature is enabled on your
device.

7Rip Alarm
Quick Start Guide
Function:
Raises an automac ‘Red Alert’ if the SoloProtect ID is forcibly removed
from a user when worn on a lanyard.
How to use:
If SoloProtect ID is forcefully pulled from the user the device will go into
‘Red Alert’.
• Alternavely if you do not want to be discreet in raising a ‘Red Alert’,
you can manually pull the pin out of the device.

8Geolocation (via GNSS)
Quick Start Guide
Function:
In conjuncon with ‘Device Check’, use to update your locaon.
How to use:
Aer compleng a 'Device Check' the LED will flash blue and show a
Geolocaon display symbol, before going solid blue with a short vibraon
when a fix is found – can take up to two minutes.
• It is difficult for any device to perform a locaon fix when indoors.

Quick Start Guide
9Multi-Function Buttons
Quick Start Guide
Function:
Each buon can be defined to make an audio call or to trigger an SMS
text message to a pre-defined contact*.
How to use:
Press one of the highlighted buons, specific to each contact to call or
trigger an SMS text*. The blue LED will flash during a call. Press the
buon again to cancel the call.
• ‘Mul-Funcon Buons’ are not for use in an alarm situaon.
* Check with your employer regarding the exact set up.

Essential Care and Maintenance
• Regularly use the ‘Device Check’ funcon. It will display two alternang red flashing lights if there is a problem.
• Leave regular ‘Amber Alert’ messages.
• Keep your SoloProtect ID clean and avoid unnecessary knocks or drops.
• SoloProtect ID is not waterproof; avoid exposure to rain or other wet condions.
• If you wear your SoloProtect ID on a lanyard, remember to check the lanyard plug regularly and replace it whenever it
becomes damaged.
• Charge your SoloProtect ID every 24 hours if possible.
Quick Start Guide

WE MAKE WORKING ALONE SAFER
Tel: [phone] (Opon 4)
[e-mail]
www.SoloProtect.com