Solton DX 43 User manual

www.solton.de
ENGLISH
DEUTSCH
USER MANUAL
D
X
43
D
X
43
CH 1 CH 2 CH 3 CH 4

D
X
43
www.solton.de
Save these instructions for later use!
• Follow all warnings and instructions marked
on the product!
• Do not use this product in the near of water, i.e.
swimming pool, wet basement, etc.
• Do not place this product onto a instable stand or
table. The product may fall down, causing damage
to the product or to persons!
• Slots and holes in the cabinet and the electronic
modules are provided for ventilation; to ensure
reliable operation of the product, do not cover any
slots or holes.
• This product should not be placed in the near
an ofen or any other hot units.
• Use only the attached (original) power mains
cable. In case of questions about power supply or
cable, please ask your local SOLTON dealer.
• Do not cover or damage the power mains cable.
• In case of damaged cables, do not use them at
all.
• The power mains cable should be unplugged if
the unit is not used for longer time.
• Never push any objects into this product.
Dangerous (high) voltage points could result in
risk of fire or electrical shock. Do not spill any liquid
on the product.
• Do not try to service this product by yourself.
Opening or removing covers may expose you to
dangerous (high) voltage or other risks. All service
should be handeled by qualified service personnel
only.
• Clean only with dry clothes.
• In case of any problems, unplug the product from
the mains supply immediately.
Contact qualified service personnel in following
cases:
• If the mains power cable or plug is damaged.
• If liquid has been spilled into the product.
• If the product has been exposed to water.
• If the product does not operate normally
according this manual.
• If the product has been dropped (damaged
chassis).
• Exposure to extremely high volume levels may
cause a permanent hearing loss.
• Individuals vary considerably in susceptibility to
noise induced hearing loss, but nearly everyone
will lose some hearing if exposed to sufficiently
intense noise for a sufficient time. The U.S.
Government´s Occupational Safety and Health
Administration (OSHA) has specified the following
permissible noise level exposures:
• According to OSHA, any exposure in excess of
the above permissible limits could result in some
hearing loss.
• Ear plug protectors in the ear canals or over the
ears must be worn when operating this product in
order to prevent a permanent hearing loss if
exposure is in excess of the limits as set forth
above. To ensure against potentially dangerous
exposure to high sound pressure.
For a period of one year from the date of delivery to the
original purchaser (as shown on the original invoice or
sales receipt), SOLTON Acoustic GmbH & Co. KG
warrants to the ORIGINAL OWNER of each product
(provided it waspurchased at an authorized SOLTON
Dealer) that it is free of defects in materials and work-
manship and that eachproduct will meet or exceed all
factory published specifications for each respective
model. SOLTON agrees to repair or replace
(at its discretion) all defective parts at no charge for
labor or materials; subject to following provisions:
SOLTON shall take no responsibility for repair or replacement
as specified under this warranty, if the damaged product
has been subject to misuse, accident, neglect or failure
to comply with normal maintenance procedures; or if the
serial number has been defaced, altered or removed.
SOLTON will accept responsibility for, or resulting from,
improper alterations or unauthorized parts or repairs.
This warranty does not cover any damage to speakers or
any other consequential damage resulting from breach of
any written or implied warranty. SOLTON will remedy any
defect, regardless of the reason for failure (except as
excluded) by repair, or replacement. SOLTON will remedy
the defect and ship the product within a reasonable
time after receipt of the defective product at an authorized
SOLTON Service Center. In the case that an SOLTON product
requires service, the owner must contact SOLTON or an
authorized SOLTON Service Center to receive an R.A.N.
(Return Authorization Number) and instructions on how
to return the product to the authorized SOLTON Service
Center, or to the factory. SOLTON (or its Authorized Service
Center) will initiate corrective repairs upon receipt of the
returned product. Please save original carton and all the
packing materials in case shipping is required. All
products being returned to the factory or service center
for repairs must be shipped pre-paid.
If the repairs made by SOLTON or the authorized SOLTON
Service Center are not satisfactory, the owner is
instructed to give written notice to SOLTON. If the defect
or malfunction remains after a reasonable amount of
attempts by SOLTON to remedy the defect or malfunction,
the owner shall then have the option to elect either a
refund or replacement of said SOLTON product free of
charge. The refund shall be an amount equal to but
not greater than the actual purchase price, not including
any taxes, interest, insurance, closing costs and other
finance charges (minus reasonable depreciation on the
product). If a refund is necessary, the owner must make
the defective or malfunctioning product available to
SOLTON free and clear of all liens or other restrictions.
SOLTON reserves the right to modify or change equipment
(in whole or part) at any time prior to delivery thereof, in
order to include therein electrical or mechanical
improvements deemed appropriate by SOLTON; but without
incurring any liability to modify or change any equipment
previously delivered, or to supply new equipment in
accordance with any earlier specifications.
DISCLAIMER OF CONSEQUENTIAL AND INCIDENTAL
DAMAGES YOU, THE OWNER, IS NOT ENTITLED TO
RECOVER FROM SOLTON ANY INCIDENTAL DAMAGES
RESULTING FROM ANY DEFECT IN THE SOLTON
PRODUCT. THIS INCLUDES ANY DAMAGE TO
ANOTHER PRODUCT OR PRODUCTS RESULTING
FROM SUCH A DEFECT.
No person has the authority to enlarge, amend, or modify
this warranty rules. This warranty is not extended by the
length of time which the owner is deprived of the use of
product. Repairs and replacement parts provided
pursuant to the warranty shall carry only the non-expired
portion of the warranty.
THIS STATEMENT OF WARRANTY SUPERSEDES ALL
OTHERS CONTAINED IN THIS MANUAL.
We continually engage in research related to product
improvement. Materials, production methods and design
refinements are introduced into existing products. Any
current SOLTON product may differ in some respect from its
published description, but will always equal or exceed the
original design specifications unless otherwise stated.
Limited liability on contents. Subjects to be changed
without prior notice.
Speaker stands, distance rods, cables and other
accessories are available as option (not included).
Important Safety Instructions
Read instructions before connecting
Limited Warranty
Information and Disclaimer!
TO PREVENT THE RISK OF FIRE AND
SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO
MOISTURE OR RAIN.
DO NOT OPEN CASE; NO USER SERVICE-
ABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL ONLY.
• Read all of these instructions clearly!
• The product has been manufactured
according to IEC 60065.
• The user must follow the advice and warning
comments found in the operating instructions.
The unit conforms to Protection Class 1.
• Loudspeaker outputs can carry dangerous
high voltage. Connect of disconnect any
speaker cable ONLY if the unit is switched off
and the unit is disconnected from the mains
power supply (wall socket).
• Do not interrupt the protective conductor
connection.
MAINS CONNECTION:
• The set operating voltage must match the
local mains supply voltage.
PLACE OF INSTALLATION:
• The unit should be used only on a clean,
horizontal working surface.
• Keep away the product from moisture and
dust.
• Keep away from direct sunlight..
• Do not place this product onto a instable
stand or table. The product may fall down,
causing damage to the product or to persons!
• Slots and holes in the cabinet and the
electronic modules are provided for ventilation;
to ensure reliable operation of the product, do
not cover any slots or holes.
• This product should not be placed in the near
an ofen or any other hot units.

D
X
www.solton.de
Dieses Gerät wurde gemäß IEC 60065 hergestellt
und hat das Werk in technisch in einwandfreiem Zustand
verlassen. Für einen gefahrlosen Betrieb muss der Anwender
die Hinweise und Warnungen dieser Bedienungsanleitung
befolgen. Dieses Gerät entspricht der Schutzklasse I.
• DIE SICHERHEIT DES GERÄTES WIRD
NUR GEWÄHRLEISTET, WENN:
• Reparaturen von autorisierten SOLTON-Servicestellen
ausgeführt werden.
• das Gerät in Übereinstimmung nach den Vorgaben dieser
Bedienungsanleitung verwendet wird.
WARNUNG:
• Wenn Abdeckungen oder Gehäuseteile entfernt werden,
können spannungsführende Bauteile freigelegt werden.
• Wartung sowie Reparatur am geöffneten Gerät unter
Spannung darf nur durch eine vom Hersteller autorisierte
Fachkraft (nach VBG 4) erfolgen, die mit den damit
verbundenen Gefahren vertraut ist.
• Lautsprecher-Ausgänge führen berührungsgefährliche
Spannungen. Verbinden Sie Lautsprecherausgänge mit
Lautsprechern mittels Kabeln nur im ausgeschalteten
Gerätezustand und nur mit dem original vom Hersteller
beigelegtem bzw. empfohlenem Netzkabel.
• Es dürfen nur Sicherungen vom Typ IEC 127 und der
angegebenen Nennstromstärke verwendet werden.
• Eine Verwendung von überbrückten Sicherungen sowie
ein Kurzschließen des Sicherungshalters ist verboten.
• Unterbrechen Sie niemals die Schutzleiterverbindung.
• Hohe Lautstärkepegel können dauerhafte Gehörschäden
verursachen. Vermeiden Sie deshalb die direkte Nähe
von Lautsprechern, die mit hoher Lautstärke betrieben
werden. Verwenden Sie einen Gehörschutz bei
dauernder Einwirkung hoher Pegel. SOLTON, der Hersteller
bzw. der Inverkehrbringer übernimmt keinerlei Haftung
oder Verantwortung für Hörschäden und andere
gesundheitliche Schäden durch die Verwendung, den
Transport oder die Installation dieses Produkts.
NETZANSCHLUSS:
• Die Geräte-Betriebsspannung muss mit der
örtlichen Netzspannung überein stimmen.
• Der Anschluss an das Stromnetz darf nur mit
dem mitgelieferten Netzteil oder Netzkabel erfolgen.
AUFSTELLORT:
• Das Gerät sollte nur auf einer sauberen und wackelfreien
Fläche stehen.
• Das Gerät darf während des Betriebs keinen
Erschütterungen ausgesetzt sein.
• Setzen Sie das Gerät nicht Feuchtigkeit und Staub aus.
• Das Gerät darf nicht in der Nähe von Wasser oder anderen
Flüssigkeiten bzw. Behältnissen mit Flüssigkeiten jeglicher
Art betrieben werden. Stellen Sie niemals einen mit
Flüssigkeit gefüllten Gegenstand auf oder in direkte Nähe
des Gerätes.
• Sorgen Sie für ausreichende Belüftung des Gerätes.
• Eventuelle Belüftungsöffnungen dürfen nicht abgedeckt
werden.
• Vermeiden Sie eine direkte Sonneneinstrahlung und die
unmittelbare Nähe von Heizkörpern, Heizstrahlern
o.ä. Geräte.
• Betrieben oder transportieren Sie das Gerät nie auf einem
instabilen Wagen, Ständer, Dreifuß, Untersatz oder Tisch.
Beim Transport, Lagerung, Aufstellung sowie beim Betrieb
des Gerätes müssen die Anweisungen des Herstellers befolgt
werden.
• Zusatzvorrichtungen: Verwenden Sie niemals Zusatzvorrichtungen,
die nicht vom Hersteller empfohlen wurden.
• Lagern Sie das Gerät über längere Zeit NUR Stromlos
(Netzstecker sollte gezogen werden).
Wir behalten uns Änderungen der technischen Daten
im Rahmen der Produktverbesserung und Produktpflege
vor. Dabei legen wir größten Wert auf Kompatibilität und
Produkttreue. Wir behalten uns Änderungen jeglicher Art
vor. Keine Gewähr für Druckfehler.
Stative, Distanzrohre, Kabel und anderes Zubehör nicht
im Lieferumfang enthalten, soweit nicht anders angegeben.
Zubehör optional erhältlich.
Für den Zeitraum eines Jahres, beginnend mit
Lieferdatum an den ursprunglichen Käufer
(abzulesen von der Rechnung bzw. Kassenbon),
gewährleistet die SOLTON ACOUSTIC GmbH & Co. KG
für jeden Neukauf, dass das Produkt sowohl vom
Material als auch in der Ausführung der Herstellung
in einwandfreiem Zustand ist. Der SOLTON ACOUSTIC
GmbH & Co.KG steht es frei zu entscheiden, unter Vorbehalt
kostenlos alle fehlerhaften Teile zu reparieren oder
zu ersetzen. Es wird keinerlei Haftung für Reparatur
oder Ersatz des Produkts übernommen, wenn
Schäden durch Installationsfehler oder
unsachgemäßen Gebrauch des Gerätes entstanden
sind, die Seriennummer beschädigt wurde oder
versucht wurde, diese zu ändern oder zu entfernen.
Die SOLTON ACOUSTIC GmbH & Co. KG übernimmt
ebenfalls keine Haftung für Schäden, die bei unsachgemäßen
Reparaturen und/oder Eingriffen entstanden sind.
Diese Gewährleistung deckt ebenfalls keine Schäden
an Lautsprechern oder Folgeschäden an jeglicher
angeschlossenen Peripherie, Personenschäden
oder anderen Primär- und Sekundärschäden ab,
die durch eine Nichteinhaltung der geschriebenen
bzw. stillschweigenden Gewährleistungsregelungen
entstanden sind. Falls ein SOLTON Produkt Service
benötigt, sollte der Eigentümer des Gerätes ein
autorisiertes SOLTON Service-Center kontaktieren.
Egal aus welchem Grunde, deckt eine Gewährleistung
die Instandsetzung oder den Austausch,
jedoch keinesfalls Schadensersatzansprüche in
irgendeiner Art auch nicht wegen Ausfallhonorar
oder anderem ab. Als Eigentümer und/oder
Anwender sind Sie nicht berechtigt, von der
SOLTON ACOUSTIC GmbH & Co. KG Schadensersatz zu
fordern, wenn Nebenschäden durch ein Produkt
aus dem Hause der SOLTON ACOUSTIC GmbH & Co. KG
entstehen. Dies schließt Folge- und/oder Nebenschäden
an anderen Produkten ein.
Die Gewährleistung darf nicht geändert werden
und wird nicht um einen Zeitraum erweitert, in
dem der Eigentümer oder Anwender das Produkt
nicht nutzen kann. Lediglich vom nicht abgelaufenen
Teil der Gewährleistungszeit betroffen sind Reparaturen
und Ersatzteile, die im Rahmen der Gewährleistungsbestimmungen
ausgeführt oder getauscht wurden.
Diese Gewährleistungserklärung ersetzt alle anderen
Erklärungen, die in dieser oder anderen oder vorherigen
Ausgaben für dieses Gerät enthalten bzw. vorhanden sind.
Wichtige Sicherheitshinweise!
Bitte vor Gebrauch lesen und aufbewahren!
Gewährleistung
Informationen und Haftungsausschluss
43

D
X
D
X
43
CH 1 CH 2 CH 3 CH 4
Front View
Rear and Side View
www.solton.de
43
STER EO
PARAL LEL
BRID GE
INP UTS
INP UTS OUT PUTS
OUT PUTS
XLR
PIN1 =GND
PIN2 =IN+
PIN3 =IN-
XLR
PIN1 =GND
PIN2 =IN+
PIN3 =IN-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STER EO
PARAL LEL
BRID GE
INP UTS
INP UTS OUT PUTS
OUT PUTS
XLR
PIN1 =GND
PIN2 =IN+
PIN3 =IN-
XLR
PIN1 =GND
PIN2 =IN+
PIN3 =IN-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC

D
X
www.solton.de
D
X
43
CH 1 CH 2 CH 3 CH 4
Volume knobs allow precise setting of input gain for CH1, CH2, CH3 and CH4.
2. Volume Knobs.
1. Rack Mounting Ears.
7. AC Power Switch.
8. Air Out Slots.
43

D
X
www.solton.de
These connectors accept input signals on balanced XLR
input plugs. See the figure at the right side for
information on polarity.
This switch is used to choose the operating mode of the power amplifier:
Mode stereo: 4 inputs (CH1, CH2, CH3 and CH4) and 4 outputs are used.
Mode parallel: 2 inputs (CH1 and CH3) and 4 outputs are used.
Mode bridge: 2 inputs (CH1 and CH3) and 2 outputs are used.
Make connection by using speakon-type speaker cables, connect to
the channel 1,2,3 and 4.
12. Output Connectors.
13. AC Power Connection.
14. Air cooling slots
11. Mode Switch
43
STE REO
PARA LLEL
BRI DGE
INPUTS
INPUTS OUTPUTS
OUTP UTS
XLR
PIN 1= GND
PIN 2= IN+
PIN 3= IN-
XLR
PIN 1= GND
PIN 2= IN+
PIN 3= IN-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LL EL
BRI DG E
INPU TS
INPU TS OU TPU TS
OUTP UTS
XLR
PIN 1= GND
PIN 2= IN+
PIN 3= IN-
XLR
PIN 1= GND
PIN 2= IN+
PIN 3= IN-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
12
12
12
12 13
14

D
X
www.solton.de
43
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
STE RE O
PARA LLE L
BRI DG E
INPU TS
INPU TS O UT PUTS
OUTP UT S
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
XLR
PIN 1=G ND
PIN 2=I N+
PIN 3=I N-
1+ 1+
1- 1-
2+ 2+
2- 2-
1+ 1+
1- 1-
2+ NC
2- NC
Speaker + to PIN 1+
Speaker - to PIN 2+
! ! A t t e n t i o n ! !
Max. Load 8 Ohms

D
X
www.solton.de
43
Rated Power
8 ohm stereo
(1KHz THD+N=0.1%) 4 ohm stereo
8 ohm bridge
Protection
Protection
Residual noise Short circuit input
Frequency response 1W 8 ohm stereo
Sensitivity 8 ohm stereo & 1 KHz
Mode switch
Crossover Bypass: 20Hz - 22KHz
Control
Cooling system
Led indicators
Connectors Input connectors
Output channel Output connectors
Input impedance Balanced
Input impedance Unbalanced
Crosstalk 8Ω 20Hz~20KHz
S/N ratio 8Ω Rated Power
Phase response 1W & 8 ohm
Slew rate
Power supply
Intermodulation distortion (IMD)
Total harmonic distortion 8Ω20Hz~20KHz RMS
Damping factor 1KHz & 8 ohm
Output Circuitry
Dimension (W x D x H) Unit / mm ( 2HU )
Carton dimension Unit / mm
Net Weight Unit / kg
Gross Weight Unit / kg
0.775V / 1.0V
DX 43
4x 300 W
4x 450 W
Specification of DX 43 Power Amplifier
DC protect, Short circuit protect, High temperature protect, current inrush
Input over load protect (Limiter), Output over load protect, Soft startup protect
<3mV
20Hz - 22KHz (+-0.5dB)
2x 900 W
within +-5 degree
Stereo / Mono (Parallel)
Bypass: 20Hz - 22KHz
Power Switch, CH1 CH2 CH3 CH4 Volume, Mode Switch
Continuously variable-speed fan
Protection / Clip-Red, Signal-Green, Active-Blue
Female XLR
Speakon connectors
20K
10K
>60dB
>100dB
11 kg
<0.10%
<0.06%
>500
Class D
>60 V/us
AC 230/240V / 50Hz
483 x 355 x 88 mm
580 x 480 x 150 mm
9 kg

D
X
c
SOLTON Acoustic
Oberer Mühlweg 6 / 94060 Pocking Rottau / GERMANY
Tel: +49 (0) 8531 / 913880 Fax: +49 (0) 8531 / 978507
Web: www.solton.de E-mail: [email protected]
All rights reserved to SOLTON Acoustic. All features and content might be changed
without prior notice. Any photocopy, translation, or reproduction of part of this
manual without written permission is forbidden. Copyright 2021 SOLTON Acoustic
43
Table of contents
Languages:
Other Solton Amplifier manuals
Popular Amplifier manuals by other brands

Hughes & Kettner
Hughes & Kettner Switchblade Tube Amp Revolution Programming guide

Rockford Fosgate
Rockford Fosgate Punch P4004 Installation & operation

Rotel
Rotel RB-1090-3 Technical manual

Linear Technology
Linear Technology DC2622A Demo Manual

CPI
CPI VZC-6967AM Installation, Operation and Preventive Maintenance manual

Soundstream
Soundstream Picasso PCA2.130 Owner's manual and installation guide