Sony Ericsson S700i User manual

Installation Instruction, Electrical
Installation Instruction, Electrical
Applicable for S700i and S700c
Contents
1General.............................................................................................................................2
2Go/No Go Testing............................................................................................................2
2.1 Test Set-up Go/No Go test ................................................................................2
2.2 Test Set ..............................................................................................................3
2.3 RF Connections Antenna Coupler.....................................................................3
2.4 RF Connections Antenna adapter (optional) .....................................................3
3Calibration.......................................................................................................................4
3.1 Test Set-up – SERP (only authorized centers) ..................................................4
3.2 Test Set ..............................................................................................................5
3.3 Power Supply.....................................................................................................5
3.4 GPIB card and cable..........................................................................................5
3.5 RF Connection...................................................................................................5
4General Equipment.........................................................................................................5
4.1 Computer ...........................................................................................................5
4.2 Dummy battery (Optional) ................................................................................5
4.3 Hardlock ............................................................................................................5
4.4 Service Card Reader and Service Card..............................................................5
4.5 SonyEricsson programming interface – SEPI ...................................................6
4.6 SonyEricsson interface – SEPI ..........................................................................6
4.7 USB PC cable....................................................................................................6
4.8 Label Printer (optional) .....................................................................................6
4.9 Infrared Device..................................................................................................6
4.10 Bluetooth Device ............................................................................................... 6
5Software ...........................................................................................................................7
5.1 EMMA II...........................................................................................................7
5.2 Labelmake software (optional)..........................................................................7
5.3 Willtek 420x Go/No Go Test Script ..................................................................8
5.4 SERP (only authorized centers).........................................................................8
6Revision History..............................................................................................................8
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
Approved according to 000 21-LXE 107 42/1

Installation Instruction, Electrical
1 General
The Electrical Installation Instructions describes the procedures for installing all of the
hardware and software needed to perform testing, calibration, software loading and repair
activities at an Electrical level for the Sony Ericsson products specified.
NOTE! This product is manufactured with lead-free solder and lead-free components.
During electrical repair, it is critical to make sure that no lead is introduced into the product.
For this reason, certain repair materials and equipment must be designated as lead-free and
labelled accordingly. A lead-free work area must be setup that is completely separated from
work areas that are used to make leaded repairs. Certain items must be designated for lead-
free work only. Some of the items that need to be clearly labelled in this way are listed in the
Equipment List Electrical. Note that any item that contacts the solder must be labelled and
used for lead-free work only.
2 Go/No Go Testing
There are two options for performing a Go No/Go test. One option is to use an RF Fixture and
the other is to use an antenna coupler together with a shielding box.
2.1 Test Set-up Go/No Go test
All test hardware necessary for this test set up is documented in the Electrical Equipment List.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
2(8)

Installation Instruction, Electrical
2.2 Test Set
An E-GSM 900/GSM 1800/GSM 1900 Test Set approved according to the Instrument List
must be used.
It should be installed according to the Instrument Manufacturer Instructions.
2.3 RF Connections Antenna Coupler
Connect the RF Cable between the RF-port of the Test set and the RF Shield box. The
Antenna Coupler should be installed into the RF Shield Box according to the supplied
instructions.
2.4 RF Connections Antenna adapter (optional)
Connect the RF-cable between the RF-port of the Test set and the Antenna adapter. Assemble
the RF probe to the RF-holder according to the information in the Test instruction Electrical.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
3(8)

Installation Instruction, Electrical
3 Calibration
3.1 Test Set-up – SERP (only authorized centers)
All test hardware necessary for this test set up is documented in the Electrical Equipment and
Instrument List.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
4(8)

Installation Instruction, Electrical
3.2 Test Set
A Test Set approved according to the Instrument List must be used.
It should be installed according to the Instrument Manufacturer Instructions.
3.3 Power Supply
Power Supply according to Instrument List must be used.
3.4 GPIB card and cable
GPIB card and cable according to the Equipment List. Use the GPIB cable to connect the
GPIB card to the test instrument.
3.5 RF Connection
RF-holder and RF probe according to Equipment List. Connect the RF probe to the RF cable.
The RF probe is held on the phone with the RF fixture.
4 General Equipment
4.1 Computer
IBM compatible computer is required. The computer should include at least two USB-ports.
Refer to Equipment List for minimum requirements.
4.2 Dummy battery (Optional)
Dummy battery to be used together with a power supply to power the phone during
calibration, Go/No Go testing and software loading. Connect the cables from the dummy
battery to the power supply, red cable to positive output terminal and black cable to negative
output terminal.
4.3 Hardlock
Hardlock with article number KRY 105 165 is required. The Hardlock should be connected to
the parallel port.
4.4 Service Card Reader and Service Card
The Service Card Reader is delivered with the necessary software and instructions for
installation. The Service Card Reader should be connected to an USB-port on the computer.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
5(8)

Installation Instruction, Electrical
4.5 SonyEricsson programming interface – SEPI
The USB programming interface is delivered with the necessary software and instruction for
installation. The USB programming interface should be connected to an USB-port on the
computer.
4.6 SonyEricsson interface – SEPI
The cable is the interface between the USB programming interface and the phone.
4.7 USB PC cable
The A-B Plug-Plug cable is the interface between the computer and the USB interface.
Connect the cable between the USB programming interface and the computer.
4.8 Label Printer (optional)
A Zebra printer model 90xi, 90xiII or 4000 deluxe shall be used. Connect the printer with a
standard RS 232 serial printer cable [refer to the Zebra printer manual] to the serial port on
the computer. Read the Zebra installation manual for more information about the installation.
4.9 Infrared Device
An RS 232 or USB type infrared adapter may be used. Install according to the manufactures
instructions.
4.10 Bluetooth Device
Any Bluetooth device as headset, other Bluetooth phone or other Bluetooth device can be
used to verify the Bluetooth function in the phone. Set up the connection according to the
chosen equipments manufacture.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
6(8)

Installation Instruction, Electrical
5 Software
5.1 EMMA II
EMMA II contains all software required to service the product. Installation and user manuals
are available in the EMMA II start page.
http://emma.extranet.sonyericsson.com
5.2 Labelmake software (optional)
LABELMAKE II THE SUCCESSOR OF LABELMAKE I
LabelMake II is an application installed through Java Web Start.
SUMMARY OF MOST IMPORTANT NEW FEATURES
• Product labels are downloaded on-line from a remote server database.
• Downloaded labels are then cached on the local hard disk so that an off-line search is
possible.
• On-line Search will download and overwrite previous cached labels. This secures that the
latest available labels are used.
• The client checks automatically if new versions of the LabelMake II software are available
whenever you start LabelMake II online.
• Some printer parameters controlled through the printer menu can now be adjusted from
within the LabelMake II application.
• LabelMake II automatically installs printers at program start up.
• Up to 4 printers attached to COM ports are supported.
• No longer have to load logos.
HOW TO INSTALL LABELMAKEII
You will find LabelMake II in the dropdown menu on the CSPN web page.
http://cspn.extranet.sonyericsson.com
Press “ START LabelMake II “ button and you will be directed to the LABELMAKE II client
page.
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
7(8)

Installation Instruction, Electrical
1/00021-2/FEA 204 544/89 B
Company Internal Sony Ericsson Mobile Communications AB
8(8)
http://emma.extranet.sonyericsson.com/labelmake/
5.3 Willtek 420x Go/No Go Test Script
An approved Sony Ericsson Test Script must be installed in the Test Instrument. The Willtek
4202 script can be downloaded from CSPN. The Test Script is located on CSPN under
Repair Instructions / Standard.
http://cspn.extranet.sonyericsson.com
Install the Test Script according to the Instrument Manufacture’s Instruction.
5.4 SERP (only authorized centers)
Download the latest revision of SERP application from CSPN. This application is located
under Repair Instructions/Standard/SERP Install package
http://cspn.extranet.sonyericsson.com
Unzip the file and open the Installation instructions.
Follow the Install instructions to install SERP.
6 Revision History
Rev. Date Changes / Comments
A 2004-09-13 First release
B 2004-12-07 Updated LabelMake Software ch 5.2