Sony Ericsson Z250 User manual

Installation Instruction, Mechanical
1/000 21-1/FEA 209 544/121 A
Company Internal
© Sony Ericsson Mobile Communications AB
Installation Instruction, Mechanical
Applicable for Z250 and Z320
Contents
1
General............................................................................................................... 2
2 Hardware ............................................................................................................ 2
2.1 Test Setup ............................................................................................. 2
2.2 Computer............................................................................................... 3
2.3 Sony Ericsson Programming Interface – SEPI...................................... 3
2.4 Sony Ericsson Programming Interface (SEPI) A1 Cable ...................... 3
2.5 Label Printer (optional) .......................................................................... 3
2.6 Service Card Reader/Service Card (optional) ....................................... 3
3 Software ............................................................................................................. 4
3.1 EMMA III................................................................................................ 4
3.2 Labelmake II software (optional) ........................................................... 4
4 Revision History................................................................................................ 5

Installation Instruction, Mechanical
1/000 21-1/FEA 209 544/121 A
Company Internal
© Sony Ericsson Mobile Communications AB
2(5)
1 General
This document describes the installation procedure for the Mechanical repair
package.
The Mechanical repair package consists of a Computer and Interface Cables. A label
printer can be installed to be able to print new labels (optional). A service card is
required for Label Make II.
2 Hardware
All hardware must be approved by Sony Ericsson and is documented in the
Equipment List.
2.1 Test Setup
The Test setup is to perform SW loading and manual test according to Test
Instruction. All necessary hardware for this test set up is documented in the
Mechanical Equipment list.

Installation Instruction, Mechanical
1/000 21-1/FEA 209 544/121 A
Company Internal
© Sony Ericsson Mobile Communications AB
3(5)
2.2 Computer
IBM compatible computer is required. The computer should include at least two USB-
ports. Refer to Equipment List for minimum requirements.
2.3 Sony Ericsson Programming Interface – SEPI
The USB programming interface is delivered with the necessary software and
instruction for installation. The USB programming interface (SEPI) should be
connected to an USB-port on the computer.
The SEPI is required when upgrading the phone.
2.4 Sony Ericsson Programming Interface (SEPI) A1 Cable
The cable is the interface between the USB programming interface (SEPI) and the
phone.
NOTE! The SEPI A1 cable must be connected with a CST-60 Standard
Charger
2.5 Label Printer (optional)
A Zebra printer model 90xi, 90xiII or 4000 deluxe shall be used. Connect the printer
with a standard RS 232 serial printer cable [refer to the Zebra printer manual] to the
serial port on the computer. Read the Zebra installation manual for more information
about the installation.
2.6 Service Card Reader/Service Card (optional)
The Service Card Reader is delivered with the necessary software and instructions
for installation. The Service Card Reader should be connected to an USB-port on the
computer.
The Service Card Reader/Service Card is required for Label Make II

Installation Instruction, Mechanical
1/000 21-1/FEA 209 544/121 A
Company Internal
© Sony Ericsson Mobile Communications AB
4(5)
3 Software
3.1 EMMA III
EMMA III contains software upgrades and tools requiring for servicing this phone.
Emma III is accessible through the CSPN. Installation and user manuals are
available at the EMMA III start page.
http://ma3.extranet.sonyericsson.com/ma3/
3.2 Labelmake II software (optional)
LabelMake II is an application installed through Java Web Start.
Access the Labelmake software from CSPN Web page.
You will find LabelMake II in the dropdown menu on the CSPN web page.
http://cspn.extranet.sonyericsson.com
Press “START LabelMake II “button and you will be directed to the LABELMAKE II
client page.
Product labels are downloaded on-line from a remote server database.

Installation Instruction, Mechanical
1/000 21-1/FEA 209 544/121 A
Company Internal
© Sony Ericsson Mobile Communications AB
5(5)
4 Revision History
Rev. Date Changes / Comments
A 2007-10-09 1st release