Sony TA-N1 User manual

3-866-957-12(1)
Stereo Power
Amplifier
 1999 by Sony Corporation
TA-N1
Operating Instructions
Mode d’emploi
GB
FR

2GB
WARNING
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to qualified
personnel only.
Do not install the
appliance in a confined
space, such as a bookcase
or built-in cabinet.
For the customers in United States
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure
that may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
CAUTION
You are cautioned that any changes or
modification not expressly approved in
this manual could void your authority to
operate this equipment.
Owner’s Record
The model and serial numbers are located
on the rear of the unit. Record the serial
number in the space provided below.
Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. TA-N1
Serial No.
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK, DO
NOT USE THIS POLARIZED AC PLUG
WITH AN EXTENSION CORD,
RECEPTACLE OR OTHER OUTLET
UNLESS THE BLADES CAN BE FULLY
INSERTED TO PREVENT BLADE
EXPOSURE.

3GB
GB
About This Manual
The instructions in this manual are for model TA-N1.
Check your model number by looking at the front panel.
In this manual, the European model is used for
illustration purposes unless stated otherwise. Any
difference in operation is clearly indicated in the text, for
example, “USA/Canada only.”
Convention
The following icon is used in this manual:
zIndicates hints and tips for making the task easier.
TABLE OF CONTENTS
Hooking Up the Components 4
Unpacking 4
Preamplifier Hookups
(Unbalanced Connections) 5
Preamplifier Hookups (Balanced Connections) 6
Speaker Hookups (Standard Connections) 7
Speaker Hookups (Bi-wired connections) 8
Power Connections 9
Location of Parts and Basic
Operations 10
Front Panel Parts Description 10
Rear Panel Parts Description 12
Additional Information 13
Precautions 13
Troubleshooting 14
Specifications 15

4GB
Hooking Up
the
Components
This chapter describes how to connect
a Sony TA-E1 preamplifier, your
speakers, and your other audio
components to the power amplifier.
Be sure to read this section before
making any connections.
Unpacking
Check that you received the following items:
• AC power cord (1)
• AC power plug adapter (3 to 2 prong polarized type) (1)
(USA/Canada only)
Before you get started
• Turn off the power to all components before making
any connections.
• Do not connect the AC power cord until all of the
connections are completed.
• Be sure to make connections firmly to avoid hum and
noise.
• When connecting an audio cord, be sure to match the
color-coded pins to the appropriate jacks on the
components: white (left) to white; and red (right) to
red.

5GB
Hooking Up the Components
Preamplifier Hookups (Unbalanced Connections)
Connect the preamplifier you are using (Sony TA-E1, etc.)
to the power amplifier’s UNBALANCED 1 or
UNBALANCED 2 input jacks. For details, refer to the
instructions supplied with the preamplifier.
L
R
L
R
2 R 1
SACDCDLINE BALANCED LINE
OUT IN
TAPE2/MD DIRECT PRE OUT
L OUT IN
TAPE1/DAT R
BALANCED OUT
L
1
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
2
CONNECTION
ASSIGNMENT
2
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
1
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A + B USE 8~16 Ω
–A–
–B–
Required cords
Audio cords (not supplied)
When connecting a cord, be sure to match the color-coded pins to
the appropriate jacks on the components.
White (L) White (L)
Red (R) Red (R)
TA-E1, etc.
TA-N1

6GB
Hooking Up the Components
Connect the BALANCED output jacks on the preamplifier
you are using (Sony TA-E1, etc.) to the power amplifier’s
BALANCED jacks. For details, refer to the instructions
supplied with the preamplifier.
Preamplifier Hookups (Balanced Connections)
Required cords
Balanced cords (not supplied)
(L) (L)
(R) (R)
1: GROUND
2: HOT (+)
3: COLD (–)
L
R
L
R
2 R 1
SACDCDLINE BALANCED LINE
OUT IN
TAPE2/MD DIRECT PRE OUT
L OUT IN
TAPE1/DAT R
BALANCED OUT
L
1
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
2
CONNECTION
ASSIGNMENT
2
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
1
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A + B USE 8~16 Ω
–A–
–B–
TA-E1, etc.
TA-N1
Note
The pin assignment of the BALANCED input jacks on the
amplifier are 1:GROUND, 2:HOT, and 3:COLD. When
connections are made to a preamplifier with a pin assignment of
1:GROUND, 2:COLD, and 3:HOT, reverse the polarities (‘and
’) of the speaker cords. For details, refer to the instructions
supplied with the preamplifier.
IN
2 3 1

7GB
Hooking Up the Components
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A +B USE 8~16 Ω
–A–
–B–
Speaker Hookups (Standard Connections)
Connect the jacks on the speakers to the SPEAKERS A or
B terminals on the power amplifier using a single speaker
cord for each speaker. There is no difference in the sound
output from SPEAKERS A and B. For details, refer to the
instructions supplied with the speakers.
Connecting the speaker cords
Caution
This is a high output amplifier.Touching the stripped
end of the speaker cords when the power is on may
result in injury.
• Be sure to check that the amplifier is turned off before
making any connections.
• Strip both ends of the speaker cords about 10 mm
(3/8in.) and twist the wire strands of the cord together
(A).
• Insert each end of the speaker cord fully into the
speaker terminal.
Be sure the stripped portion of the speaker cord does
not protrude outside of the speaker terminal cover
(USA/Canada only) nor from the speaker terminal (B).
Required cords
Speaker cords (1 pair) (not supplied)
Connect the jacks on the speaker to the power amplifier’s
SPEAKERS A or B terminals.
Notes on speaker hookup
• Connect the right speaker to the “R” terminals, and
connect the left speaker to the “L” terminals.
• Be sure to match the ends of the speaker cord to the
appropriate terminal on the components: + to + and –
to –. If the cords are reversed, the sound will be
distorted and will lack bass.
• When the maximum input level of the speakers you are
using is low, try to avoid excessive power output from
this unit to the speakers by controlling the volume on
the preamplifier. Continuously playing an audio source
at a level that distorts the audio output may damage the
speakers.
• The speaker terminals on this unit are compatible with
Y lug jack connection (European model only).
10 mm
(3/8in.)
speaker cord
AB
(Speaker terminal cover is
on USA/Canadian models
only.)

8GB
Hooking Up the Components
Speaker Hookups (Bi-wired Connections)
When the speakers you are making connections to can be
bi-wired, bi-wired connections can be made to this unit.
Connect the two sets of jacks on the speaker to the
SPEAKERS A and B terminals on this unit using two
speaker cords for each speaker. For details, refer to the
instructions supplied with the speakers.
Connecting the speaker cords
Caution
This is a high output amplifier.Touching the stripped
end of the speaker cords when the power is on may
result in injury.
• Be sure to check that the amplifier is turned off before
making any connections.
• Strip both ends of the speaker cords about 10 mm
(3/8in.) and twist the wire strands of the cord together
(A).
• Insert each end of the speaker cord fully into the
speaker terminal.
Be sure the stripped portion of the speaker cord does
not protrude outside of the speaker terminal cover
(USA/Canada only) nor from the speaker terminal (B).
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A +B USE 8~16Ω
–A–
–B–
TA-N1
Required cords
Speaker cords (2 pair) (not supplied)
Connect the jacks on the speaker to the power amplifier’s
SPEAKERS A and B terminals.
Notes on speaker hookup
• Connect the right speaker to the “R” terminals, and
connect the left speaker to the “L” terminals.
• Be sure to match the ends of the speaker cord to the
appropriate terminal on the components: + to + and –
to –. If the cords are reversed, the sound will be
distorted and will lack bass.
• When the maximum input level of the speakers you are
using is low, try to avoid excessive power output from
this unit to the speakers by controlling the volume on
the preamplifier. Continuously playing an audio source
at a level that distorts the audio output may damage the
speakers.
• The speaker terminals on this unit are compatible with
Y lug jack connection (European model only).
zAbout bi-wired connections
Bi-wired connections can be carried out when the speaker has
two sets of input terminals that separate high and low frequency
audio signals.
10 mm
(3/8in.)
speaker cord
AB
(Speaker terminal cover is on
USA/Canadian models only.)

9GB
Hooking Up the Components
Power Hookup
Before connecting the AC power cord of this power
amplifier to a wall outlet:
• Make sure that the power switch on the power
amplifier is in the off position.
• Connect the speakers.
Connect the supplied power cord to the AC IN terminal
on this unit.
Connecting to the power outlet
(European model only)
Connect the supplied power cord to a wall outlet.
3-pronged grounded outlet
(USA/Canadian model only)
The supplied power cord has a 3-pronged grounded plug.
If you are using a 3-pronged grounded outlet, the plug
can be inserted directly into the outlet. However, if the
socket is a 2-pronged grounded outlet, use the supplied
AC power plug adapter or a commercially available AC
power plug adapter.
If noise (hum) is produced
Noise may be caused by an electrical potential difference on the
ground circuit*. In this case, use the supplied AC power plug
adapter and be careful not to connect the ground lead to
anything.
* Although the ground of the domestic outlet is normally a safety
ground, a slight electrical potential difference may be
produced, depending on the outlet. Therefore, use of the
supplied 3-pronged power cord may lessen the quality of the
audio signal or may produce humming noise.
Note
We recommend that you connect this unit directly to a wall
outlet. If you must use a multi-outlet tap, or extension cord, be
sure to use one capable of handling high current (at least 10 A) or
one designed for office use.
2-pronged polarized outlet
• When using a grounded outlet (the inlets are different sizes)
Use the supplied AC power plug adapter.
3 to 2 prong polarized
AC power plug adapter
N pole

10GB
Front Panel Parts
Description
Location of
Parts and Basic
Operations
This chapter explains the names and
basic operations of the buttons and
controls located on the front and rear
panels.

11GB
Location of Parts and Basic Operations
1U(power) switch
Press to turn the power amplifier on and off.
• When turning the power on, turn down the volume on the
preamplifier to a minimum, then turn the preamplifier and
this unit on respectively. Similarly, when turning the power
off, turn down the volume on the preamplifier, then turn
the amplifier and preamplifier off respectively. This is done
to prevent damage to the speakers.
2Input indicators (BALANCED/UNBALANCED 1/
UNBALANCED 2)
Light to indicate the input selected with the INPUT
SELECTOR control on the rear panel.
PROTECTION
BALANCED UNBALANCE UNBALANCE
12
1
23
3PROTECTION indicator
Lights for about 16 seconds after the power is turned
on. After that, the blue light above the indicator lights.
When there is a short circuit in one of the speakers, the
protection circuitry in this unit is automatically
activated. The PROTECTION indicator lights when
the protection circuitry is activated, and sound is not
produced from the speakers. Should this occur, turn
the power off, and check that the speakers connections
are correct.

12GB
Location of Parts and Basic Operations
1
7 6 53
4
2
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A + B USE 8~16Ω
–A–
–B–
Rear Panel Parts Description
1SPEAKERS A jacks
For details, see page 7.
2SPEAKERS B jacks
Use with SPEAKERS A terminals when bi-wired
speaker connections are made (page 8).
3AC IN terminal
Use to connect the supplied power cord to theAC IN
terminal to supply power to this unit from a wall
outlet.
4BALANCED input jacks
Use to connect the BALANCED output jacks on a
preamplifier to this unit (page 6). Select BALANCED
with the INPUT SELECTOR knob (5).
5INPUT SELECTOR control
Turn to select the input.
6UNBALANCED 1 input jack
Use to connect the PRE OUT jacks on a preamplifier to
this unit (page 5). Select UNBALANCED 1 with the
INPUT SELECTOR knob (5).
7UNBALANCED 2 input jack
Use to connect the PRE OUT jacks on a preamplifier to
this unit (page 5). Select UNBALANCED 2 with the
INPUT SELECTOR knob (5).

13GB
Additional Information
Additional
Information Precautions
On safety
Should any solid object or liquid fall into the cabinet,
unplug the power amplifier and have it checked by
qualified personnel before operating it any further.
On power sources
• Before operating the power amplifier, check that the
operating voltage is identical with your local power
supply. The operating voltage is indicated on the
nameplate at the rear of the power amplifier.
• If you are not going to use the power amplifier for a
long time, be sure to disconnect the power amplifier
from the wall outlet. To disconnect the AC power cord,
grasp the plug itself; never pull the cord.
• AC power cord must be changed only at the qualified
service shop.
On placement
• Place the power amplifier in a location with adequate
ventilation to prevent heat buildup and prolong the life
of the power amplifier.
• Do not place the power amplifier near heat sources, or
in a place subject to direct sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the cabinet that might
block the ventilation holes and cause malfunctions.
• Do not place the power amplifier:
– Any place that is not level or unstable.
– On top of a carpet or blanket.
– In an extremely cold place.
– Near a television or video deck.
(If used near a television or video deck, you may
experience noise in the audio and/or video signals.
The possibility of such interference greatly increases
when using an indoor TV antenna. We recommend
always using an external TV antenna.)
• Although this is a rationally designed stereo power
amplifier, it does emit an extremely large amount of
heat. Therefore, do not place anything on top of this
unit. Also, when using several of these units together
with high power connections, do not stack them
directly on top of one another. Either place each one on
an individual shelf of a rack, or place them side by side
horizontally.

14GB
Additional Information
Troubleshooting
If you experience any of the following difficulties while
using the power amplifier, use this troubleshooting guide
to help you remedy the problem. Should any problem
persist, consult your nearest Sony dealer.
There’s no sound or only a very low-level sound
is heard.
/Check that the speakers and components are
connected securely.
/Make sure that all connections have been made
securely.
/Make sure that you have selected the correct
component on the control amplifier.
The protection indicator does not go out or the
protection indicator lights and no sound is heard.
/Turn off the power amplifier, check that there are
no short circuits in the speaker connections.
The left and right sounds are unbalanced or
reversed.
/Check that the speakers and components are
connected correctly and securely.
/Make sure all connections are made with the
correct polarity (+ and –).
Severe hum or noise is heard.
/Check that the speakers and components are
connected securely.
/Check that the connecting cords are away from a
transformer or motor, and at least 10 feet (3 meters)
away from a TV set or fluorescent light.
/Move your TV away from the audio components.
/The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
On heat emission during use
This unit will become very hot during use. This is not a
malfunction.
The entire surface of the cabinet will become quite hot,
especially when playing at high volumes. In such cases,
do not touch the cabinet. Touching the cabinet may cause
physical injury or fire.
In addition, do not use this unit in a completely enclosed
cabinet. Place it in a well ventilated location to prevent an
excessive rise in temperature.
On operation
Before connecting other components, be sure to turn off
and unplug the power amplifier.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any question or problem concerning your
power amplifier, please consult your nearest Sony dealer.
Precautions

15GB
Additional Information
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 8 ohm loads, both channels driven,
from 20 - 20,000 Hz; rated 200 watts per
channel minimum RMS power, with no
more than 0.05% total harmonic
distortion from 250 milliwatts to rated
output (USA model only).
Amplifier section
Power Output 200 W + 200 W (8 Ω)
400 W + 400 W (4 Ω)
Speaker Nominal Impedance:
4 Ω ∼ 16 Ω
Harmonic distortion
less than 0.005% (at 8 Ω, 10 W, THD)
Dumping factor
150 (at 8 Ω, 1 kHz)
Frequency response
5 Hz ~ 300 kHz + 0/– 1 dB (at 8 Ω, 1 W)
Input sensitivity and Impedance
1.5 V, 20 kΩ (Unbalanced)
1.5 V, 40 kΩ (Balanced)
Gain 28 dB
S/N more than 115 dB (Input shorted, A-Fil)
General
System Pure-complementary High Power Legato
Linear SEPP MOS FET power amplifier
Power requirements
USA and Canadian models
120 V AC, 60 Hz
European models
230 V AC, 50/60 Hz
Power consumption
USA and Canadian models
8.0 A
European models
600 W
Dimensions 480 ×245 ×530 mm
(187/8×9 5/8×20 7/8in.)
including projecting parts and controls
Mass (Approx.)70 kg (154 lbs. 4 oz.)
Supplied accessories
See page 4.
Design and specifications are subject to change without
notice.

2FR
AVERTISSEMENT
Afin d’éviter tout risque
d’incendie ou
d’électrocution, ne pas
exposer cet appareil à la
pluie ou à l’humidité.
Afin d’éviter tout risque
de choc électrique, ne pas
ouvrir le coffret. Confier
toute réparation à un
technicien qualifié
uniquement.
N’installez pas l’appareil
dans un espace confiné
comme dans une
bibliothèque ou un
meuble encastré.
A l’attention de la clientèle canadienne
ATTENTION:
POUR PREVENIR LES CHOCS
ELECTRIQUES, NE PAS UTILISER CETTE
FICHE POLARISEE AVEC UN
PROLONGATEUR, UNE PRISE DE
COURANT OU UNE AUTRE SORTIE DE
COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND
SANS EN LAISSER AUCUNE PARTIE A
DECOUVERT.

3FR
FR
Au sujet de ce mode
d’emploi
Les instructions de ce mode d’emploi couvrent le modèle
TA-N1. Vérifiez le numéro de votre modèle sur le
panneau avant. Dans ce manuel, les illustrations
représentent le modèle européen, sauf mention contraire.
Toute différence de fonctionnement est clairement
indiquée dans le texte, par exemple, “Etats-Unis/Canada
seulement”.
Convention
L’icône suivante est utilisée dans ce mode d’emploi :
zIndique des conseils et suggestions pouvant faciliter
certaines opérations.
TABLE DES MATIÈRES
Raccordement des appareils 4
Déballage 4
Raccordement d’un préamplificateur (liaisons
asymétriques) 5
Raccordement d’un préamplificateur (liaisons
symétriques) 6
Raccordement des enceintes (liaisons standard) 7
Raccordement des enceintes (liaisons doubles) 8
Raccordement de l’alimentation 9
Nomenclature et opérations
élémentaires 10
Description des éléments du panneau avant 10
Description des éléments du panneau arrière 12
Informations complémentaires 13
Précautions 13
Guide de dépannage 14
Spécifications 15

4FR
Raccordement
des appareils
Ce chapitre explique comment
raccorder un préamplificateur Sony
TA-E1, vos enceintes et vos autres
appareils audio à l’amplificateur de
puissance. Veuillez lire attentivement
ce paragraphe avant d’effectuer les
liaisons.
Déballage
Vérifiez si les accessoires suivants se trouvent bien dans le
carton d’emballage.
• Cordon d’alimentation secteur (1)
• Adaptateur de prise d’alimentation secteur (type
polarisé 3 à 2 broches) (1)
(Etats-Unis/Canada seulement)
Avant de commencer
• Mettez tous les appareils hors tension avant d’effectuer
les liaisons.
• Ne raccordez les cordons d’alimentation secteur que
lorsque toutes les liaisons sont terminées.
• Enfoncez les fiches à fond dans les prises pour éviter
tout bourdonnement et bruit.
• Lorsque vous raccordez un cordon audio, branchez les
fiches sur les prises de même couleur : blanc (gauche) à
blanc et rouge (droit) à rouge.

5FR
Raccordement des appareils
Raccordement d’un préamplificateur (liaisons asymétriques)
Raccordez le préamplificateur que vous utilisez (Sony
TA-E1, etc.) aux prises d’entrée UNBALANCED 1 ou
UNBALANCED 2 de l’amplificateur de puissance. Pour
les détails, voir le mode d’emploi fourni avec le
préamplificateur.
L
R
L
R
2 R 1
SACDCDLINE BALANCED LINE
OUT IN
TAPE2/MD DIRECT PRE OUT
L OUT IN
TAPE1/DAT R
BALANCED OUT
L
1
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
2
CONNECTION
ASSIGNMENT
2
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
1
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A + B USE 8~16 Ω
–A–
–B–
Cordons nécessaires
Cordons audio (non fournis)
Lorsque vous raccordez un cordon, veillez à brancher les fiches
sur les prises appropriées sur les appareils.
TA-E1, etc.
TA-N1
Blanc (gauche) Blanc (gauche)
Rouge (droite) Rouge (droite)

6FR
Raccordement des appareils
Raccordement d’un préamplificateur (liaisons symétriques)
Cordons nécessaires
Cordons symétriques (non fournis)
(L) (L)
(R) (R)
1: GROUND
2: HOT (+)
3: COLD (–)
L
R
L
R
2 R 1
SACDCDLINE BALANCED LINE
OUT IN
TAPE2/MD DIRECT PRE OUT
L OUT IN
TAPE1/DAT R
BALANCED OUT
L
1
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
2
CONNECTION
ASSIGNMENT
2
3
1 :GROUND
2 :HOT ( + )
3 :COLD ( – )
1
1
1
2
3
2
CONNECTION
ASSIGNMENT
BALANCEDINPUT SELECTOR
IMPEDANCE USE 4~16Ω
L
L
+
+
–
–
R
R
–
–
+
+
BALANCEDUNBALANCED
L
L
R
R UNBALANCED 12
1 : GROUND
2 : HOT(+)
3 : COLD(–)
INPUT
SPEAKERS
A + B USE 8~16 Ω
–A–
–B–
TA-E1, etc.
TA-N1
Remarque
L’affectation des broches des prises de sortie BALANCED sur
l’amplificateur est 1 : GROUND, 2 : HOT et 3 : COLD. Si vous
raccordez l’amplificateur à un préamplificateur dont l’affectation
des fiches est 1 : GROUND, 2 : COLD et 3 : HOT, inversez la
polarité (‘et ’) des cordons d’enceintes. Pour les détails,
reportez-vous au mode d’emploi du préamplificateur.
IN
2 3 1
Reliez les prises de sortie BALANCED du
préamplificateur que vous utilisez (Sony TA-E1, etc.) aux
prises d’entrée BALANCED de l’amplificateur de
puissance. Pour les détails, voir le mode d’emploi fourni
avec le préamplificateur.