Sony CDX-CA900 Product guide

Sony Corporation © 2002 Printed in Thailand
CDX-CA900
Cautions
•This unit is designed for negative earth 12 V
DC operation only.
•Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
•Before making connections, turn the car
ignition off to avoid short circuits.
•Connect the yellow and red power input leads
only after all other leads have been connected.
•Run all earth wires to a common earth
point.
•Be sure to insulate any loose unconnected
wires with electrical tape for safety.
Notes on the power supply cord (yellow)
•When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
•When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
The numbers in the list are keyed to those in the
instructions.
Caution
Handle the bracket 1carefully to avoid injuring
your fingers.
Installation/Connections
安裝線路連接
FM/MW/LW
Compact Disc
Player
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B-
)
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the interface cable of a car telephone
5To a car’s illumination signal
Be sure to connect the black ground lead to it
first.
6To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to it
first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
7To the +12 V power terminal which is energised
at all times
Be sure to connect the black earth lead to it first.
1
6 7
Equipment used in illustrations (not supplied)
插圖中的裝置（非附送）
Rear speaker
後揚聲器
Front speaker
前揚聲器
1
Power amplifier
功率放大器
CD/MD changer
CD/MD 換碟機
×4
4
×2
5
3-241-107-21 (1)
2 3
2
A
B
SUB OUT (MONO)
AUDIO OUT
REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
Source selector*
音源選擇器*
XA-C30
*not supplied
非附送
AUDIO OUT
FRONT
Active subwoofer
有源超低音揚聲器
Rotary commander RM-X4S
旋轉式控制器 RM-X4S
89 q;
⊕ Κ3 × 12

R
AUDIO OUT
FRONT
AUDIO OUT
REAR
BUS
AUDIO
L
注意
•本機只能使用負極接地 12 V 直流電源。
•不要使導線夾在螺栓下，或繞掛在移動部件上
（如：座椅扶手上）。
•進行連接之前，請先關閉汽車的點火器，以避免
短路。
•黃色和紅色電源輸入導線必須在所有其它導線都
連接完畢以後才連接。
•將所有地線都連接到同一接地點。
•為了安全，請確認把沒有連接的導線用電器膠帶
包紮進行絕緣。
電源導線須知（黃色）
•將本機與其它立體聲裝置相連接時，所連接的
汽車電路容量必須大於每個裝置保險絲容量的
總和。
•當汽車電路容量不夠大時，請將本機直接與電
池相連接。
零件一覽表（1）
圖示數字與說明書中的數字是一致的。
注意
移動裝卸支架 1 時，請特別注意別傷到手指。
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner or when you
activate the AF (Alternative Frequency), TA (Traffic
Announcement) function.
• When your car has built-in FM/MW/LW aerial in
the rear/side glass, connect the power aerial
control lead (blue) or the accessory power input
lead (red) to the power terminal of the existing
aerial booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms,
and with adequate power handling capacities to
avoid its damage.
• Do not connect the speaker terminals to the car
chassis, or connect the terminals of the right
speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in
speaker wires installed in your car if the unit shares
a common negative (–) lead for the right and left
speakers.
• Do not connect the unit’s speaker cords to each
other.
線路連接圖例（2）
註 （2-A）
•
務必在接放大器之前連接地線 。
•
如果您連接了選購的功率放大器而不使用內裝的放大
器，將無嘟聲功能
。
要領 （2-B- ）
若要連接 2 台或更多 CD/MD 換碟機時，必須使用音源選
擇器 XA-C30（選購件）。
線路連接圖（3）
1至汽車的金屬部位
首先連接黑色接地導線，然後再連接黃色和紅色電源
輸入導線。
2至電動天線控制導線或天線升壓放大器的電源導線
註
• 如無電動天線，天線增壓器，或用手操作的套管式
天線，便不須連接此導線。
• 您的汽車的後側玻璃窗中如果內裝有 FM/MW/LW 天
線，即請參看“控制和電源線須知”。
3至選購的功率放大器的 AMP REMOTE IN（放大器遙控
輸入）
本連接僅用於放大器。連接任何其它系統可能會損壞
本機。
4至汽車電話的接口電纜
5至汽車照明電源
務請首先將黑色接地導線與其連接。
6至在點火鑰匙的輔助位置上通電的 +12 V 電源端子
註
• 若沒有輔助位置，則請連接至常時通電的 +12 V 電
源（電池）端子。
務請首先將黑色接地導線與其連接。
• 您的汽車的後側玻璃窗中如果內裝有 FM/MW/LW 天
線，即請參看“控制和電源線須知”。
7至隨時都通電的 +12 V 電源端子
務請首先將黑色接地導線與其連接。
控制和電源線須知
• 當您打開調諧器或啟動 AF（變換頻率）或 TA（交通公
告）功能時，電源天線控制導線（藍色）提供 +12 V 直
流電。
• 若您的汽車後側玻璃窗上有內置 FM/MW/LW 天線，
須將電動天線控制導線（藍色）或輔助電源輸入導線
（紅色）連接到現有天線放大器上的電源端子上。詳
細內容請向銷售商諮詢。
• 本機不能使用不具備繼電箱的電動天線。
保持記憶的線路連接法
當連接好黃色電源輸入導線時，即使汽車發動機點火鑰匙
被轉在電源切斷之處，電源仍繼續將電流供給記憶用電路，
以保持所記憶著的數據。
連接揚聲器時的注意事項
• 連接揚聲器電線以前，請先切斷本機電源。
• 使用阻抗為 4-8Ω 且具有充分功率處理容量的揚聲
器，以免損壞揚聲器。
• 不要將揚聲器端子連接到汽車底盤上或將右揚聲器端
子與左揚聲器端子相連接。
• 切勿將本機的接地導線連接至揚聲器的負(-)接線柱。
• 揚聲器不可以並聯連接。
• 請僅連接無源揚聲器。若將有源揚聲器（帶內置放大
器）連接到揚聲器端子上會損壞本機。
• 若本裝置使用左、右揚聲器的共用(-)極導線，為了避
免故障，切勿使用已安裝在汽車內的內置揚聲器導
線。
• 請勿將本裝置揚聲器導線相互連接。
3
from car aerial
來自汽車天線
2
5
4
AMP REM 7
Max. supply current 0.3 A
最大供電量 0.3 A
Fuse (10 A)
保險絲（10 A）
Red
紅色
Yellow
黃色
Black
黑色
Blue/white striped
藍白條紋
White
白色
Green
緣色
Purple
紫色
White/black striped
白黑條紋
Grey/black striped
灰黑條紋
Green/black striped
緣黑條紋
Purple/black striped
紫黑條紋
Grey
灰色
Supplied with XA-C30
附帶於 XA-C30
3
Left
左
Right
右
Left
左
Right
右
3
ANT REM
1
Blue
藍色
Max. supply current 0.1 A
最大供電量 0.1 A
Light blue
淡藍色
6
ATT
Source selector
(not supplied)
音源選擇器
（非附送）
XA-C30
Supplied with the CD/MD changer
附帶於 CD/MD 換碟機
*1
*1
7
ILLUMINATION
Orange/white striped
橙白條紋
*3
*2
BUS AUDIO IN
/AUX IN*4
BUS
CONTROL IN
AUDIO OUT
REAR
AUDIO OUT
FRONT
*1RCA pin cord (not supplied)
RCA 針型插頭電線（非附送）
*2Auxiliary optional equipment
such as portable DVD player (not
supplied)
輔助選購裝置，如便攜式 DVD 播放
機（非附送）
*3supplied with the auxialiry
equipment
附帶於輔助裝置
*4Be sure to match the colour-
coded code for audio to the
appropriate jacks from the unit.
If you connect a optional unit,
you cannot use AUX IN terminal.
確保音頻色碼編碼與裝置上的正確
插孔相一致。
如果連接選購裝置 CD/MD 裝置，則
不能使用 AUX IN 端子。
*5Insert with the cord upwards
電線向上插入
SUB OUT (MONO) REMOTE IN
*5

1
1
2
4AB 1 2 3
Bend these claws outward
for a tight fit, if necessary.
若有必要，則可向外彎曲這些卡爪，
以便牢固安裝。
4
4
5
54
4
Dashboard
儀表板
5
5
6A TOYOTA
to dashboard/centre console
至儀表板中央控制箱
Bracket
托架
Bracket
托架
max. size
5 ×8 mm
最大尺寸
5×8 mm
B NISSAN
4
max. size
5 ×8 mm
最大尺寸
5×8 mm
4
to dashboard/centre console
至儀表板中央控制箱
Bracket
托架
Bracket
托架
4
max. size
5 ×8 mm
最大尺寸
5×8 mm
max. size
5 ×8 mm
最大尺寸
5×8 mm
4
Existing parts supplied with your car
隨汽車附送的部件
Existing parts supplied with your car
隨汽車附送的部件
Fire wall
防火壁
1
2
x
1
6
*
1
A
B
7Mounting example
安裝例子 12 3
Markings
記號
456
9
8
q;
Heavy duty tape etc.
強力膠帶等
the other hole
另一個孔
q;
Precautions
•Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
•Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperatures,
such as in direct sunlight or near heater ducts.
•Use only the supplied mounting hardware for a
safe and secure installation.
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
How to detach and attach the
front panel (4)
Before installing the unit, detach the front
panel.
4-A To detach
Before detaching the front panel, be sure to press
(OFF). Press (OPEN), then slide the front panel
to the right side, and pull out the left side.
4-B To attach
Place the hole in the front panel onto the
spindle on the unit as illustrated, then push the
left side in.
Mounting example (5)
Installation in the dashboard
Note (5-*)
When installing this unit: Depending on car
type, the mounting angle may not allow the
front panel to open easily. In such a case,
remove the silver screw Ashown below.
When screwing it on again, first lock the lever B.
Attaching the screw without doing so may cause
the unit to break.
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the supplied
screws 4.
Warning when installing in a car
without ACC (accessory) position
on the ignition key switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
RESET button
When the installation and connections are
completed, be sure to press the RESET button
with a ballpoint pen, etc., after removing the front
panel.
2
9
Mark
記號
使用前注意事項
•仔細選取安裝位置，以使本裝置不干擾正常的駕駛
操作。
•避免將本機安裝在受灰塵，污物和強烈振動影響的
區域，或安裝在高溫處，如直對陽光下或熱氣管道
附近。
•為了安裝安全和可靠，請使用附送的安裝構件。
安裝角度之調整
請在 60 度以內調整安裝角度。
如何拆卸和裝配前面板（4）
安裝本機之前，請先拆卸前面板。
4-A 拆卸
拆卸前面板之前，須先按 (OFF) 。
按 (OPEN) ，然後將前面板滑向右側，再將左
側拉出。
4-B 裝配
如圖所示，將前面板的 孔搭在本機的支軸
上，然後推入左側。
安裝示例（5）
安裝在儀錶板裡
註（5-*）
安裝本機時：有些車型的車輛其安裝角度可能會
使機器的前面板不易開啟。此時，請如下面所示卸下
銀螺釘 A。
再旋上螺釘時，請先鎖定操作桿 B。裝螺釘時
不如此作，便可能造成裝置損壞。
將本機安裝於日本產汽車上時
（6）
有的日本產汽車不能安裝本機，在這種情形下，請向
Sony 經銷商諮詢。
註
為防止發生故障，安裝時只能使用附送的螺絲
4 。
安裝在點火鑰匙開關上沒有 ACC（附
件）位置的汽車上時的警告
在關掉汽車引擎之後，一定請按下裝置上的
(OFF) 兩秒以關掉時鐘顯示。
如果只短暫地按一下 (OFF)，將不會關掉時鐘顯示
而浪費電池。
RESET 按鈕
當安裝和連接完成後，務請用原子筆等按壓 RESET
按鈕。
安裝轉式控制器（7）
註
• 旋轉型遙控器請裝在不妨礙汽車駕駛之處。
• 將旋轉式控制器安裝在直徑約為 55 mm 的圓形平面上。
• 不可把旋轉型遙控器裝在對（前座位）乘客有危險的地
方。
• 裝遙控器時，請注意不要讓螺絲釘傷及安裝面反面的電
線等。
• 把遙控器安裝在高溫，如直射陽光底下或受暖氣機熱流
吹擊的地方。
將本裝置安裝在轉向柱外殼上
1 選擇旋轉式控制器的準確位置進行臨時安裝，然後
按按鈕並轉動控制器，以保證主機反應正常。
您可以轉動旋轉式控制器上的撥盤以改變紅外線的
方向。
注意
安裝旋轉式控制器時，務必使安裝地點處於機器上感受器
的有效距離之內。
2 清潔安裝表面。
污垢或油會削弱貼在安裝底座 9 上雙面黏膠帶
的黏和強度。
3 畫一個供螺絲釘鑽孔之處。
用安裝底座 9 上的螺絲孔作位置記號。
註
確信安裝底座上的記號定位與旋轉式控制器的相同，然後
再安裝。
4 取下轉向柱外殼，並在所作記號之處鑽開 2 mm
大小的釘孔。
5 用吹風機等工具將安裝表面和安裝底座 9 上的
雙面膠帶加熱至 20 °C 至 30 °C 之間，然後施以
均勻的壓力將安裝底座 9 貼在安裝表面。最後
用附送的螺絲 8 將其擰緊。
在安裝面的反面之螺絲釘尖端部分，張貼強力膠帶
等，以免傷朗轉向柱裡面的電線等。
註
請仔細選擇安裝位置。黏膠的黏力很強，重新定位可能較
為困難。
要將螺絲擰緊，使螺絲頭不突出。
6 裝上轉向柱外殼後，將旋轉式控制器裝在安裝底座
上，直至鎖定在圖中所示的位置。
注意
• 如果主機或旋轉式控制器暴露在直射陽光下，紅外線接
收器或發射器的靈敏度將可能削弱，主機可能無法正確
工作。在此情況下，請轉動撥盤重新調整紅外線的方
向。
• 旋轉式控制器安裝於方向盤附近時，切記繫上所提供的
保險帶 q; 。
• 切記勿使保險帶 q; 纏住汽車操作裝置(如排檔、變速器
等)。
• 將保險帶 q; 懸掛於指示器開關上後，切記擰緊保險帶
q; 上的閉鎖裝置。
要領
保險帶 q; 上有兩個孔。您可任選其中之一使用。
註
在把遙控器裝在轉向柱外殼時，必須注意轉向柱裡的螺絲釘
之尖端，不可刺到或傷害到轉向柱殼裡面的轉軸、開關的操
作部分或電線等。
(PUSH)
Infrared rays dial
紅外線撥盤
Releasing the rotary commander
拆下旋轉式控制器
Installing the rotary commander
(7)
Notes
• Choose the mounting location carefully so that the
rotary commander will not interfere with operating
the car.
• Install the rotary commander on a flat surface with a
circular area of approximate 55 mm diameter.
• Do not install the rotary commander where it may
jeopardize the safety of the (front) passenger in
anyway.
• When installing the rotary commander, be sure not
to damage the electrical cables etc. on the other side
of the mounting surface.
• Avoid installing the rotary commander where it may
be subject to high temperatures, such as from direct
sunlight or hot air from the heater etc.
When installing the unit on the steering
column cover
1 Choose the exact location for the rotary
commander to be mounted temporarily,
then press the buttons and rotate the
controls to make sure that your master unit
reacts well.
You can change the direction of infrared rays
by turning the dial on the rotary commander.
Caution
Be sure that the place where you install the rotary
commander is within the range of the receptor on
the unit.
2 Clean the mounting surface.
Dirt or oil impair the adhesive strength of the
double-sided adhesive tape preattached to the
mounting holder 9.
3 Mark the position for the supplied screw.
Use the screw hole on the mounting holder 9
to mark the position.
Note
Make sure the orientation of the markings on both
the mounting holder and the rotary commander is
the same, and then attach.
4 Remove the steering wheel column cover,
and drill 2 mm diameter hole where you
have marked.
5 Warm the mounting surface and the double-
sided adhesive tape on the mounting holder
9with a hair drier, etc., to a temperature
between 20 °C and 30 °C, and attach the
mounting holder 9onto the mounting
surface by applying even pressure. Then
screw it down with the screw 8.
Attach a piece of heavy duty tape etc. on the
other side of the mounting surface to cover the
protruding tip of the screw so that they will not
interfere with the electrical cables etc. inside
the steering wheel column.
Note
Choose the mounting location carefully. The
adhesive is very strong and relocation may be
difficult.
Tighten the screw firmly so that the screw head
does not protrude.
6 After installing the steering wheel column
cover, attach the rotary commander to the
mounting holder until it locks into place as
illustrated.
Cautions
• If the master unit or the rotary commander is
exposed to direct sunlight, sensitivity of the
infrared receptor or emitter may deteriorate and
the master unit may not work properly. If this
happens, rotate the dial to readjust the direction of
infrared rays.
• Be sure to attach the supplied strap q; when
installing the rotary commander near the steering
wheel.
• Be sure that the strap q; does not get caught on the
car controls (gear, shifter, etc.).
• Be sure to tighten the stopper of the strap q; after
hanging the strap q; on the indicator switch, etc.
Tip
There are two holes for the strap q;. You can use
whichever hole you prefer.
Note
If you are mounting the rotary commander to the
steering wheel column, make sure that the
protruding tip of the screw on the inner surface of
the column do not in anyway hinder or interfere with
the movement of the rotating shaft, operative parts
of the switches or the electrical cables etc. inside the
column.