Sony Pressman TCS-60DV User manual

TCS-60DV
US Model
Canadian Model
AEP Model
E Model
SERVICE MANUAL
CASSETTE CORDER
MICROFILM
SPECIFICATIONS
Model Name Using Similar Mechanism TCM-50DV
Tape Transport Mechanism Type MT-50-30
Recording system 4-track 2 channel stereo
Tape speed 4.8 cm/s or 2.4 cm/s
Frequency range 250 – 8,000 Hz using nomal (TYPE1) cassette
(with REC TIME switch at “NORMAL”)
Speaker Approx. 3.6 cm (17/16 in.) dia. ×2
Power output Speakers : 160 mW + 160 mW
(at 10 % harmonic distortion)
Headphones : 6 mW + 6 mW
(at 10 % harmonic distortion)
Input Microphone input jack (minijack) sensitivity
0.2 mV for 3 Ωor lower impedance
microphone
Output 2(headphones) jack (minijack) for
8 – 300 Ωearphone
Variable range of the tape speed
From approx. +25 % to – 15 %
(with REC TIME switch at “NOMAL”)
Power requirements 3 V DC batteries AA (R6) ×2/
External DC 3 V power sources
Dimensions (w/h/d)(incl. projecting parts and controls)
Approx. 88.7 ×113.4 ×41.3 mm
(31/2×41/2×111/16 inches), incl.
Mass Approx. 280 g (9.9 oz)
Design and specifications are subject to change without notice
Ver 1.0 1999. 03

— 2 —
TABLE OF CONTENTS
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
1. SERVICE NOTE ······························································· 3
2. GENERAL ·········································································· 4
3. DISASSEMBLY
3-1. Cabinet (rear)Assy, Lid Sub Assy, Cassette ··················· 5
3-2. MAIN Board, Mechanism Deck ····································· 5
3-3. Belt·················································································· 6
3-4. Head ················································································ 6
3-5. Motor, DC ······································································· 7
3-6. Precaution ForAttaching The MAIN Board···················7
4. ADJUSTMENT ································································· 8
5. DIAGRAMS
5-1. Block Diagram ································································ 9
5-2. Schematic Diagram······················································· 11
5-3. Printed Wiring Board –MAIN Section – ······················ 15
5-4. Printed Wiring Board –LED Section – ························· 20
5-5. IC Block Diagrams ······················································· 24
5-6. IC Pin Function Discription ·········································· 26
6. EXPLODEDVIEWS
6-1. MAIN Section -1 ·························································· 27
6-2. MAIN Section -2 ·························································· 28
6-3. Mechanism Deck Section -1 ········································· 29
6-4. Mechanism Deck Section -2 ········································· 30
7. ELECTRICAL PARTS LIST ······································· 31

— 3 —
PULSE
10Hz 1.6V (4.5dB)
Oscillator
(Side B) (Side A)(Side A)
TP41
TP1
S301
S302
SECTION 1
SERVICE NOTE
The TCS-60DV detects rotation of both the supply and take-up side
reels using the PH701 (photo reflector). Because the PH701 is
mounted on the Main board, auto stop is activated and reel rotation
cannot be detected when the Main board is removed. To check the
operation of mechanism deck and voltage without the Main board,
follow the procedure as described below.
How to remove the Main board (opening the Main board)
1) Refer to page 5 “3. Disassembly”.
How to enter the fast forward/rewind modes
1) Input the square wave to the TP41. (Refer to the illustration
below.)
2) Press the fast forward/rewind keys.
3) Turn on the S301.
How to enter the playback mode
1) Input the square wave to the TP41. (Refer to the illustration
below.)
2) Press the playback key.
3) Set the S302 to the PLAY.
4) Turn on the S301.
How to enter the record mode
1) Input the square wave to the TP41. (Refer to the illustration
below.)
2) Press the record key.
3) Set the S302 to the REC.
4) Turn on the S301.

— 4 —
SECTION 2
GENERAL This section is extracted
from instruction manual.
!™ Tape direction indicators
!£ SPEAKER (REAR SIDE)
!¢ TAPE COUNTER switch
!∞ Flat mic
!§ PAUSE cswitch
!¶ REC TIME switch
!• BATT/REC indicator
!ª VOR switch
@º Battery compartment
@¡ iindicator
@™ DC IN 3V jack
12Headphone jack
2MIC (PULG IN POWER) jack
3VOL knob
4rREC button
5pSTOP button
6PLAY button
7SPEED CONTROL knob
8REW/REVIEW button
9FF/CUE button
0DIR cswitch
!¡ Hand strap

— 5 —
SECTION 3
DISASSEMBLY
Disassemble the unit in the order as shown below.
Note : Follow the disassembly procedure in the numerical order given.
3-1. “CABINET (REAR) ASSY”,“LID SUB ASSY, CASSETTE”
Set "Cabinet (rear) assy", "lid sub assy, cassette" Main board, Mechanism deck Belt Head
Motor, dc
3-2. MAIN BOARD, MECHANISM DECK
1 Two screws(+B1.7 × 9)
2 Two screws(+B1.7 × 9)
4 Remove speaker cable (4pcs)
5 PWB, LED Flexible
6 Shaft(A), stopper
7 Screw, ornamental
8 Screw, ornamental
9 Lid Sub Assy, Cassette
Claws
3 Remove the Cabinet (rear) assy
in the direction of the allow
Claws
5 PC board, Motor flexible
1 Three screws(IB LOCK)
8 Mechanism deck
6 PC board, Head flexible
3 Two screws(M1.4), Toothed lock
7 MAIN board
2
4
NOTE: For attaching the Main board,
refer to the next page.

— 6 —
3-3. BELT
1 Belt(motor)
Belt(motor)
2 Belt(flywheel)
Belt(flywheel)
3 Belt(counter)
Belt(counter)
• How to thread the belt
3-4. HEAD
1 two screws
2 head, magnetic
(REC/PB/ERASE)

TCS-60DV
— 11 — — 12 — — 13 — — 14 —
5-2. SCHEMATIC DIAGRAM
12
A
B
C
D
E
F
G
H
I
J
K
L
M
O
P
34567891011121314151617181920212223242526
•Waveform
1TP45 REC DOUBLE MODE
TP45 REC NORMAL MODE
1
52 kHz
10 µsec/div
5 V/div
10 µsec/div
10 V/div
5 µsec/div
1 V/div
52 kHz
IC303 3LX REC
2
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
• % : indicates tolerance.
•C: panel designation.
•U: B+ Line.
•H: adjustment for repair.
• Power voltage is dc3V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : REC/PB
( ) : REC
< > : PB
• Voltagesaretaken witha VOM (Inputimpedance 10MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E: REC
a: PB

TCS-60DV
— 15 — — 16 — — 17 — — 18 — — 19 —
5-3. PRINTED WIRING BOARD – MAIN SECTION –
12
A
B
C
D
E
F
G
3456789101112131415161718192021222324
Note on Printed Wiring Board:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•Through hole is omit.
•b: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on thepattern facesideseen from
(SIDE A) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(SIDE B) the parts face are indicated.
Ref. No. Location
D301 B-2
D302 B-20
D303 C-23
D304 C-22
D305 E-13
D306 C-20
D307 B-3
D308 C-9
D701 B-9
D702 B-14
IC101 A-5
IC201 B-17
IC301 D-6
IC303 B-3
IC304 B-19
IC305 D-18
IC501 A-15
IC601 E-14
IC701 C-14
IC702 B-15
Q101 C-6
Q201 B-6
Q301 D-4
Q302 A-19
Q303 B-18
Q304 C-3
Q305 C-2
Q306 B-2
Q307 D-22
Q308 A-1
Q501 B-15
Q502 C-6
Q503 B-7
Q601 D-11
Q602 E-11
Q603 D-11
Q604 C-11
Q701 B-15
Q702 B-9
Q703 D-15
Q704 C-15
Q705 B-13
Q706 B-13
Q707 D-14
Q708 B-7
• Semiconductor
Location

TCS-60DV
— 20 — — 21 — — 22 — — 23 — — 24 —
5-4. PRINTED WIRING BOARD – LED SECTION –
12
A
B
C
D
E
345678910111213
Note on Printed Wiring Board:
•X: parts extracted from the component side.
•Y: parts extracted from the conductor side.
•Through hole is omit.
•b: Pattern from the side which enables seeing.
Caution:
Pattern face side: Parts on the pattern faceside seen from
(SIDE A) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
(SIDE B) the parts face are indicated.
5-5. IC BLOCK DIAGRAMS
IC501 NJM2072M IC502 MM1251BFBE
1
2
3
4
8
7
6
5
GND
AMP OUT
GAIN CONT
INPUT VCC
OUTPUT2
OUTPUT1
RECOVERY
TIME CAP
CT
OUT
N.C
GND VS
VCC HYS N.C
1 2 3 4
5678
–
+
–
+
BOOSTER
SIRCUIT
IC304 TA7688F-S0 IC305 CXA2500N-T4
9
IN2
NF1 VR
GND
BASE
BY2
OUT1 VB1
NF2
BY1
PW VCC
OUT2
MUTE
VB2
IN1
10111213141516
1 52 3 4 6 7 8
–
+
RIPPLE
FILTER
MUTE
PW-OFF
–
+
DC
DC
REFERENCE
MIC INPUT (A)
PB OUTPUT (A)
REC DRIVE INPUT (A)
REC DRIVE OUTPUT (A)
AGC TIME CONSTANT
TAPE/TUNER SELECTOR
1 2
PB PRE INPUT (A)
PB NF (A)
3 4 5
PB EQ SWITCH (A)
TUNER INPUT (A)
LINE OUTPUT (A)
6 7 8 9
10 11 12
REC DRIVE OUTPUT (B) VCC PB/REC SELECTOR13
14 15
PB OUTPUT (B) PB NF (B) PB PRE INPUT (B) MIC INPUT (B) GND
20 21 22 23 24
TUNER INPUT(B) PB EQ SWITCH (B)
18 19
REC DRIVE INPUT (B) LINE OUTPUT (B)
16 17
TAPE/
TUNER
REF AGC
MIC
NORM/
METAL
GCA
PB LINE REC
AGC
DET
AMP
AGC
MIC GCA
PB LINE REC
AGC
DET
AMP
MIC GCA
PB LINE REC
AMP
PB/
REC
6dB 22dB 12dB -0.3dB 20.5dB
Ref. No. Location
D501 E-3
D502 E-4
D503 E-6
IC502 E-5
Q504 E-3
Q505 E-7
• Semiconductor
Location

— 25 —
IC301 LA7473V-TLM
IC601 LB1877V-TLM
EXT AMP NFB2-R EXT AMP NFB1-R EXT IN-R INPUT SELECT CTL-2 MIC VCC HPF ON INT IN-R INT AMP NFB-R MIX AMP OUT-R MIX BUFF IN-L INT AMP OUT-R GND
INPUT SELECT CTL-1
EXT IN-L
RIPPLE FILTER
INT IN-L
EXT AMP NFB1-L EXT AMP NFB2-L
VCC
INT AMP NFB-L
INT AMP OUT-L
MIX BUFF IN-R
MIX AMP OUT-L
HPF IN-L
OUT-L
BIAS
MIC MONO
HPF IN-R OUT-R EXT/INT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
161718
192021222324252627282930
EXT MIC
DET
EXT MIC
AMP L
EXT MIC
AMP R
INT MIC
AMP L MIX
AMP L OUTPUT AMP L
RIPPLE
FILTER
MIC
VCC INT MIC
AMP R MIX
AMP R OUTPUT AMP R
BIAS
ON
OFF
ON
OFF EXT
INT
EXT
INT
UOUT DR VCC LB FC OUT VSP IN+ VREF S/S
20 19 18 17 16 15 14 13 12 11
VOUT
WOUT
P-GND
WB
VB
UB
OSC
COM
GND
RI
1 2 3 4 5 6 7 8 9 10
DRIVER STARTUP
DIR LOGIC
STARTUP
DET
WAVEFORM
DET
CURRENT
DET
SPEED
DET
LOCKING
PROTECT
OSC
BIASREF V
TSD +
–

— 26 —
5-6. IC PIN FUNCTION DESCRIPTION
IC701 TB2004FN-020-ER(SYSTEM CONTROL)/MAIN BOARD
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14 – 16
17
18
19
20
21
22
23
24
I/O
–
–
I
I
I
I
I
I
I
I
I
–
–
–
O
O
O
O
O
–
O
–
Description
Ground
For generation of system clock (fosc = 3.2 kHz)
Reset signal input
PAUSE ON/OFF by the PAUSE switch and V•O•R switch “L”: ON, “OPEN”: OFF
Recovery to FWD when opening/closing the cassette lid “L”: ON, “OPEN”: OFF
Direction “L”: ON, “OPEN”: OFF
REC/PB selection “L”: ON, “OPEN”: OFF
FF/REW “L”: ON, “OPEN”: OFF
POWER : ON/OFF “L”: ON, “OPEN”: OFF
Photo reflector pulse input for tape end detection
FWD/REV selection “L”: ON, “OPEN”: OFF
Not used
Not used
Not used
LED ON/OFF “L”: ON, “OPEN”: OFF
Audio mute “L”: ON, “OPEN”: OFF
Motor brake “L”: ON, “OPEN”: OFF
Motor direction “L”: FWD, “OPEN”: OFF
Motor ON/OFF “L”: ON, “OPEN”: OFF
Power supply for CMOS block
Voltage doubler circuit control output
Power supply for bipolar block
Pin Name
GND
OSC
CL
IN-1
IN-2
IN-3
IN-4
IN-5
IN-6
IN-7
IN-8
I/O-1
I/O-2
OUT-8 – 6
OUT-5
OUT-4
OUT-3
OUT-2
OUT-1
VDD
CONT
VCC

SECTION 6
EXPLODEDVIEWS
— 27 —
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delayshould be anticipatedwhen orderingthese
items.
• Themechanical partswith noreference number
in the exploded views are not supplied.
• Accessories and packing materials are given in
the last of this parts list.
1
2
2
3
47
11
8
9
5
6
MIC901
MIC902
14 10
12
13
12
A
A
B
B
6-1. MAIN SECTION-1
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 A-3050-908-A LID SUB ASSY, CASSETTE
2 3-704-197-31 SCREW(M1.4 ×3.0), LOCKING
3 3-033-592-01 HOLDER, MICROPHONE
4 3-033-593-01 CUSHION, MICROPHONE
5 3-033-594-01 COVER, MICROPHONE
6 3-318-382-31 SCREW(1.7 ×3), TAPPING
7 1-673-130-11 PWB,LED FLEXIBLE
*8 3-033-584-01 HOLDER, CASSETTE
9 3-318-382-01 SCREW(1.7 ×3), TAPPING
10 3-311-772-11 SHAFT (A), STOPPER
11 A-3021-186-A LED BOARD, COMPLETE
12 3-315-989-11 SCREW, ORNAMENTAL
13 3-704-245-42 SCREW (1.4)
*14 X-3370-480-1 TOGGLE ASSY
MIC901 1-542-298-11 MICROPHONE, ELECTRET CONDENSER (L)
MIC902 1-542-298-11 MICROPHONE, ELECTRET CONDENSER (R)

— 28 —
6-2. MAIN SECTION-2
55
51
52
53 54
56
58
62
57
60
61
63
59
70
66
69
70
68
67
65
SP902
SP901
MT-50-30
72
71
64
64
not supplied
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 3-704-197-33 SCREW (IB LOCK)
52 X-3377-632-1 CABINET (FRONT) ASSY
53 3-032-431-01 KNOB(PAUSE)
54 3-032-432-01 KNOB(DIR)
55 3-925-231-01 REFLECTOR
56 X-3376-766-1 LEVER ASSY,COVERING INDICATION
57 3-831-441-99 SPACER, KNOB
58 3-925-230-01 SPRING, BATTERY COIL
59 3-925-229-01 TERMINAL, PLUS
60 4-017-441-01 CUSHION (B)
61 3-345-648-01 SCREW (M1.4), TOOTHED LOCK
62 A-3021-185-A MAIN BOARD, COMPLETE
63 X-3377-552-1 CABINET (REAR) ASSY
64 3-318-382-31 SCREW (1.7 ×3), TAPPING
65 3-328-319-01 STRAP, HAND
66 3-032-441-01 SHEET (PICK)
67 9-911-815-01 CUSHION
68 3-033-582-01 LID, BATTERY CASE
69 3-032-436-01 FOOT(B), RUBBER
70 3-318-203-92 SCREW (B1.7 ×9), TAPPING
*71 3-035-577-01 PAPER, SHIELD
72 3-570-611-00 SHEET, PROTECTION, LID
SP901 1-544-657-11 SPEAKER (3.6cm) (L)
SP902 1-544-657-11 SPEAKER (3.6cm) (R)

— 29 —
6-3. MECHANISM DECK SECTION-1
(MT-50-30)
123
124
128
118
121 122
116
127
112
119 120
125
126
101
102
103
106
109
105 104
108
110
130
130 129
115
129
111
107
113 112
128
117
HRPE901
M601
114
not
supplied
not
supplied
not supplied
not
supplied
• A
NOTE : Refer to next page.
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 3-925-247-11 BUTTON, FF
102 3-925-246-11 BUTTON, REW
103 3-925-245-11 BUTTON, PLAY
104 3-032-787-01 BUTTON, REC
105 3-925-248-11 BUTTON, STOP
106 3-924-595-01 SPRING (PINCH-N), TORSION
107 X-3370-380-1 ARM(PINCH-R) ASSY
108 3-924-596-01 SPRING (PINCH-R), TORSION
109 X-3370-379-1 ARM(PINCH-N) ASSY
*110 3-924-572-01 LEVER (DIR)
*111 3-924-575-01 LEVER (DIR-M)
112 3-924-601-01 SPRING, TENSION
113 X-3370-378-1 LEVER (HEAD) ASSY
114 3-938-133-01 SCREW
115 3-018-121-01 SPRING (B.T), COMPRESSION
116 3-365-630-02 SCREW (M1.4)
117 X-3370-375-1 TABLE ASSY, REEL
*118 3-924-535-01 LEVER (FR)
*119 3-924-534-01 LEVER (C/R)
*120 3-924-538-01 LEVER (S-OFF)
121 3-321-483-11 RING, RETAINING
122 3-924-569-01 PAD(S-OFF)
123 1-657-172-11 PC BOARD, MOTOR FLEXIBLE
124 3-704-245-42 SCREW (1.4)
125 3-035-367-11 BELT (MOTOR)
126 3-924-577-01 PULLEY (COUNTER)
*127 3-924-536-01 LEVER (OFF)
128 3-924-602-01 SPRING, TENSION
129 3-305-925-00 WASHER
130 3-321-483-01 RING, RETAINING
M601 1-698-804-21 MOTOR, DC
(including PULLEY)(CAPSTAN/REEL)
HRPE9011-500-590-11 HEAD, MAGNETIC (REC/PB/ERAES)

— 30 —
6-4. MECHANISM DECK SECTION-2
(MT-50-30)
156
158
158
159
160
161
155
154 163 191
164
166
153
151
152 167
168
169 185
161
162
159
176
175 159
178
179
159
183
184
174
173
172
171 170
177
180
159
182
183
184
186
187
188
189
190
157
165
(included • A)
NOTE : Refer to befor page
181
not supplied
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151 X-3370-373-1 CHASSIS ASSY
*152 3-924-537-01 LEVER (F/R)
153 3-924-605-01 SPRING (FF), TENSION
154 3-924-593-01 BELT (FLYWHEEL)
155 3-701-437-51 WASHER
156 X-3377-138-1 FLYWHEEL ASSY
157 3-924-602-01 SPRING, TENSION
158 3-924-558-01 PULLEY (T)
159 3-321-483-11 RING, RETAINING
160 3-924-548-01 ARM(T-N)
161 3-924-557-01 GEAR (T)
162 3-924-549-01 ARM(T-R)
*163 3-924-539-01 LEVER (REW-F)
*164 3-924-540-01 LEVER (REW-R)
165 3-924-603-01 SPRING (F/R), TENSION
166 3-924-597-01 SPRING (F/R), TORSION
*167 3-924-568-01 LEVER (FF)
*168 3-924-567-01 LEVER (REW)
*169 3-924-566-01 LEVER (STOP)
*170 X-3370-377-1 LEVER (REC) ASSY
*171 3-924-565-01 LEVER (PLAY)
172 3-924-598-01 SPRING (P/S), TORSION
173 3-924-604-01 SPRING (PLAY), TENSION
*174 3-924-547-01 ARM (PLAY-SUB)
*175 3-924-545-01 LEVER (LOCK)
*176 3-924-546-01 LEVER (SW)
177 3-924-606-01 SPRING (LOCK), TENSION
178 3-924-725-01 REFLECTOR
179 3-924-579-01 GEAR (REF)
180 3-348-993-01 WASHER
181 X-3370-376-1 LEVER (CENTER) ASSY
182 3-924-556-01 GEAR (REW)
183 3-924-562-01 GEAR (FF)
184 3-924-560-01 GEAR (REEL)
185 3-924-600-01 SPRING (REC), TENSION
186 3-032-620-01 BELT (COUNTER)
187 3-704-245-42 SCREW (1.4)
188 3-032-438-01 BRACKET (COUNTER)
189 1-548-582-11 COUNTER, TAPE (SMALL TYPE)
*190 3-924-574-01 LEVER (PAUSE)
191 3-924-607-01 SPRING (ARM-T), TENSION

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 31 —
SECTION 7
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specifiedinthe diagramsor the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS:
uF: µF
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• COILS
uH: µH
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
A-3021-185-A MAIN BOARD, COMPLETE
********************
< CAPACITOR >
C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C102 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C104 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C106 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C107 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C108 1-164-490-11 CERAMIC CHIP 0.068uF 16V
C109 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C110 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C111 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C112 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C113 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C114 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C115 1-135-318-11 TANTAL. CHIP 33uF 20% 4V
C116 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C117 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C118 1-164-346-11 CERAMIC CHIP 1uF 16V
C119 1-164-346-11 CERAMIC CHIP 1uF 16V
C120 1-164-346-11 CERAMIC CHIP 1uF 16V
C121 1-164-346-11 CERAMIC CHIP 1uF 16V
C122 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C123 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C124 1-104-908-11 TANTAL. CHIP 47uF 20% 4V
C125 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C126 1-164-676-11 CERAMIC CHIP 2200PF 5% 16V
C127 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C128 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C129 1-164-346-11 CERAMIC CHIP 1uF 16V
C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C202 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C204 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C206 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C207 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C208 1-164-490-11 CERAMIC CHIP 0.068uF 16V
C209 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C210 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C211 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C212 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V
C213 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C214 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C215 1-135-318-11 TANTAL. CHIP 33uF 20% 4V
C216 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C217 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C218 1-164-346-11 CERAMIC CHIP 1uF 16V
C219 1-164-346-11 CERAMIC CHIP 1uF 16V
C220 1-164-346-11 CERAMIC CHIP 1uF 16V
C221 1-164-346-11 CERAMIC CHIP 1uF 16V
C222 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C223 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C224 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C225 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C226 1-164-676-11 CERAMIC CHIP 2200PF 5% 16V
C227 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C228 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C229 1-164-346-11 CERAMIC CHIP 1uF 16V
C302 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C303 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V
C304 1-113-682-11 TANTAL. CHIP 33uF 20% 10V
C305 1-104-752-11 TANTAL. CHIP 33uF 20% 6.3V
C306 1-104-752-11 TANTAL. CHIP 33uF 20% 6.3V
C307 1-164-695-11 CERAMIC CHIP 0.0022uF 5% 50V
C308 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V
C309 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C310 1-104-848-11 TANTAL. CHIP 100uF 20% 4V
C311 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C312 1-104-847-11 TANTAL. CHIP 22uF 20% 4V
C313 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V
C314 1-104-847-11 TANTAL. CHIP 22uF 20% 4V
C315 1-126-246-11 ELECT CHIP 220uF 20% 4V
C316 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C317 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C318 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C319 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V
C320 1-104-848-11 TANTAL. CHIP 100uF 20% 4V
C321 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C322 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C323 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C324 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C325 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C326 1-164-672-11 CERAMIC CHIP 1500PF 5% 16V
C327 1-164-672-11 CERAMIC CHIP 1500PF 5% 16V
C501 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C502 1-104-847-11 TANTAL. CHIP 22uF 20% 4V
C503 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C505 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C506 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
MAIN

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
— 32 —
C507 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C510 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C601 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C602 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C603 1-164-337-11 CERAMIC CHIP 2.2uF 16V
C604 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C605 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C606 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V
C607 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C608 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V
C701 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C702 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C704 1-164-346-11 CERAMIC CHIP 1uF 16V
C705 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C706 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C707 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V
C708 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C709 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V
C710 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
< DIODE >
D301 8-719-049-09 DIODE 1SS367-T3SONY
D302 8-719-988-61 DIODE 1SS355TE-17
D303 8-719-988-61 DIODE 1SS355TE-17
D304 8-719-988-61 DIODE 1SS355TE-17
D305 8-719-977-03 DIODE DTZ5.6B
D306 8-719-977-03 DIODE DTZ5.6B
D307 8-719-977-03 DIODE DTZ5.6B
D308 8-719-977-03 DIODE DTZ5.6B
D701 8-719-988-61 DIODE 1SS355TE-17
D702 8-719-049-09 DIODE 1SS367-T3SONY
< FERRITE BEAD >
FB101 1-500-444-11 FERRITE 0uH
FB201 1-500-444-11 FERRITE 0uH
FB301 1-500-444-11 FERRITE 0uH
< IC >
IC101 8-759-701-02 IC NJM2073M
IC201 8-759-701-02 IC NJM2073M
IC301 8-759-380-80 IC LA7473V-TLM
IC303 8-759-434-03 IC RH5RH331A-T1
IC304 8-759-205-43 IC TA7688F-SO
IC305 8-752-089-40 IC CXA2500N-T4
IC501 8-759-701-51 IC NJM2072M
IC601 8-759-566-10 IC LB1877V-TLM
IC701 8-759-494-76 IC TB2004FN-020-ER
IC702 8-759-280-84 IC S-81211SG-QA-T1
< JACK >
J301 1-774-321-31 JACK (SMALL TYPE)(MIC)
J302 1-750-061-11 JACK,DC(POLARITY UNIFIED TYPE)(DC IN 3V)
J303 1-695-514-21 JACK (SMALL TYPE) 1P(HEAD PHONE)
< JUMPER CHIP >
JC101 1-216-295-91 SHORT 0
JC102 1-216-864-11 METAL CHIP 0 5% 1/16W
JC103 1-216-295-91 SHORT 0
JC104 1-216-295-91 SHORT 0
< COIL >
L301 1-412-030-11 INDUCTOR CHIP 22uH
L302 1-414-222-11 INDUCTOR 120uH
L303 1-412-030-11 INDUCTOR CHIP 22uH
< PHOTO INTERRUPTER >
PH701 8-749-925-05 REFLECTOR NJL5183KA-F20-TE1
< TRANSISTOR >
Q101 8-729-420-53 TRANSISTOR UN5115
Q201 8-729-420-53 TRANSISTOR UN5115
Q301 8-729-230-63 TRANSISTOR 2SC4116-YG
Q302 8-729-141-48 TRANSISTOR 2SB624-BV345
Q303 8-729-420-53 TRANSISTOR UN5115
Q304 8-729-402-93 TRANSISTOR UN5214-TX
Q305 8-729-823-86 TRANSISTOR 2SA1745
Q306 8-729-402-93 TRANSISTOR UN5214-TX
Q307 8-729-402-93 TRANSISTOR UN5214-TX
Q308 8-729-402-93 TRANSISTOR UN5214-TX
Q501 8-729-230-63 TRANSISTOR 2SC4116-YG
Q502 8-729-420-53 TRANSISTOR UN5115
Q503 8-729-402-81 TRANSISTOR XN4501
Q601 8-729-823-86 TRANSISTOR 2SA1745
Q602 8-729-823-86 TRANSISTOR 2SA1745
Q603 8-729-402-93 TRANSISTOR UN5214-TX
Q604 8-729-402-96 TRANSISTOR UN5114
Q701 8-729-402-93 TRANSISTOR UN5214-TX
Q702 8-729-230-63 TRANSISTOR 2SC4116-YG
Q703 8-729-402-96 TRANSISTOR UN5114
Q704 8-729-422-41 TRANSISTOR XN1114
Q705 8-729-230-63 TRANSISTOR 2SC4116-YG
Q706 8-729-402-93 TRANSISTOR UN5214-TX
Q707 8-729-420-16 TRANSISTOR XN1214
Q708 8-729-420-24 TRANSISTOR 2SB1218A-QRS
< RESISTOR >
R101 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R102 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R103 1-216-821-11 METAL CHIP 1K 5% 1/16W
R104 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R105 1-216-821-11 METAL CHIP 1K 5% 1/16W
R106 1-216-839-11 METAL CHIP 33K 5% 1/16W
R107 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R108 1-216-833-91 RES,CHIP 10K 5% 1/16W
R109 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R110 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R111 1-216-839-11 METAL CHIP 33K 5% 1/16W
R112 1-216-839-11 METAL CHIP 33K 5% 1/16W
R113 1-216-835-11 METAL CHIP 15K 5% 1/16W
R114 1-216-813-11 METAL CHIP 220 5% 1/16W
R115 1-216-841-11 METAL CHIP 47K 5% 1/16W
R116 1-216-851-11 METAL CHIP 330K 5% 1/16W
R117 1-216-835-11 METAL CHIP 15K 5% 1/16W
R119 1-216-831-11 METAL CHIP 6.8K 5% 1/16W
R120 1-216-793-11 RES,CHIP 4.7 5% 1/16W
R121 1-216-833-91 RES,CHIP 10K 5% 1/16W
MAIN