Sony Sony Car Stereo System XR-M510 User manual

SERVICE MANUAL
FM/MW/LW CASSETTE CAR STEREO
AEP Model
UK Model
E Model
XR-M510
Ver 1.0 2000.12
9-870-230-11 Sony Corporation
2000L0553-1 Audio Entertainment Group
C2000.12 General Engineering Dept.
SPECIFICATIONS
Dolby noise reduction manufactured under license from
Dolby Laboratories.
“DOLBY” and the double-D symbol ;are trademarks
of Dolby Laboratories.
General
Outputs Audio output (2)
Power aerial relay control
lead
Power amplifier control
lead
Inputs Telephone ATT control
lead
Illumination control lead
Tone controls Bass ±9 dB at 100 z
Treble ±9 dB at 10 k z
Power requirements 12 V DC car battery
(negative earth)
Dimensions Approx. 178 × 50 × 182 mm
(w/h/d)
Mounting dimensions Approx. 182 × 53 × 163 mm
(w/h/d)
Mass Approx. 1.3 kg
Supplied accessories Card remote commander
RM-X96
Parts for installation and
connections (1 set)
Design and specifications are subject to change
without notice.
Cassette player section
Tape track 4-track 2-channel stereo
Wow and flutter 0.08 % (WRMS)
Frequency response 30 – 20,000 z
Signal-to-noise ratio
Tuner section
FM
Tuning range 87.5 – 108.0 M z
Aerial terminal External aerial connector
Intermediate frequency 10.7 M z/450k z
Usable sensitivity 8 dBf
Selectivity 75 dB at 400 k z
Signal-to-noise ratio 66 dB (stereo),
72 dB (mono)
armonic distortion at 1 k z
0.6 % (stereo),
0.3 % (mono)
Separation 35 dB at 1 k z
Frequency response 30 – 15,000 z
MW/LW
Tuning range MW: 531 – 1,602 k z
LW: 153 – 279 k z
Aerial terminal External aerial connector
Intermediate frequency 10.7 M z/450 k z
Sensitivity MW: 30 µV
LW: 40
µ
V
Power amplifier section
Outputs Speaker outputs
Speaker impedance 4 – 8 ohms
Maximum power output 50 W × 4 (at 4 ohms)
Dolby NR off
61 dB
58 dB
Dolby B NR
67 dB
64 dB
Cassette type
TYPE II, IV
TYPE I
Model Name Using Similar Mechanism WX-C5000/XR-M500R
Tape Transport Mechanism Type MG-25E-136
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

2
XR-M510
TABLE OF CONTENTS
1. SERVICING NOTES............................................... 3
2. GENERAL
Location of Controls ....................................................... 4
Setting the Clock ............................................................. 4
Changing the Sound and Display Settings ..................... 5
Installation....................................................................... 5
Connections ..................................................................... 6
3. DISASSEMBLY ......................................................... 10
4. ASSEMBLY................................................................. 14
5. MECHANICAL ADJUSTMENTS ....................... 19
6. ELECTRICAL ADJUSTMENTS
Tape Deck Section .......................................................... 19
Tuner Section .................................................................. 20
7. DIAGRAMS
7-1. Block Diagram – TUNER/TAPE Section – .................. 21
7-2. Block Diagram – MAIN Section – ................................ 22
7-3. Block Diagram
– DISPLAY/BUS CONTROL Section – ....................... 23
7-4. Block Diagram – POWER SUPPLY Section – ............. 24
7-5. Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 25
7-6. Printed Wiring Boards
– MAIN Board (Component Side) – .............................. 26
7-7. Printed Wiring Boards
– MAIN Board (Conductor Side) – ................................ 27
7-8. Schematic Diagram – MAIN Board (1/4) – .................. 28
7-9. Schematic Diagram – MAIN Board (2/4) – .................. 29
7-10. Schematic Diagram – MAIN Board (3/4) – .................. 30
7-11. Schematic Diagram – MAIN Board (4/4) – .................. 31
7-12. Printed Wiring Boards –SUB Board –........................... 32
7-13. Schematic Diagram – SUB Board – .............................. 33
7-14. Printed Wiring Boards – DISPLAY Board –................. 34
7-15. Schematic Diagram – DISPLAY Board – ..................... 35
7-16. IC Pin Function Description ........................................... 38
8. EXPLODED VIEWS ................................................ 45
9. ELECTRICAL PARTS LIST ............................... 49
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

3
XR-M510
R625
R626
R719
R720
IC601
SECTION 1
SERVICING NOTES
PRECAUTION ON OPEN/CLOSE FRONT PANEL
The front panel opens to the bottom of main unit.
In performing the repair, place the main unit on the base having
the height exceeding 1 cm.
Open the front panel by supplying the power through the follow-
ing steps:
1. Disconnect the motor connector (CN501) from main board.
2. Supply the power to the motor.
Voltage : 9 V
Yellow wiring : MOTOR –
Black wiring : MOTOR +
front panel
XR-M510
( SIDE VIEW)
1cm
base
black wiring yellow
wiring
connector
(CN501)
–
+
MODEL IDENTIFICATION
There are three types of main board in according of destination.
– MAIN Board (Component Side) –
– MAIN Board (Conductor Side) –
R625 R626 R719 R720 Indicated language
TYPE A aa ××
English, Spanish,
Swedish, Portuguese
TYPE B ××aa
French, German, Dutch,
Italian
South a××aEnglish, Czeck, Polish,
European Turkish
TYPEA, B, or South European model can also be identified from
the front panel display language.
For a switching method of display language, see page 5.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

4
XR-M510 SECTION 2
GENERAL This section is extracted from
instruction manual.
6
Location of controls
SOURCE
123456
CLOSE OFF
DISC
DISC
ENTER
SOUND
MENU
LIST
REP SHUF
D
S
P
L
P
T
Y
M
O
D
E
XR-M510
TAAF
D-BASS
Security side
Operation side
7
qk TA button 16, 17, 18
ql SOUND button
w; PRST/DISC +/– (cursor up/do n) buttons
SEEK/AMS –/+ (cursor left/right) buttons
13
wa ENTER button
ws CLOSE button
wd D-BASS button
*Warning when installing in a car
without ACC (accessory) position on
the ignition key switch
Be sure to press (OFF) on the unit for
t o seconds to turn off the clock display
after turning off the engine.
When you press (OFF) only momentarily,
the clock display does not turn off and this
causes battery wear.
The corresponding buttons of the unit
control the same functions as those on
the card remote commander.
10 Reset button 8
2Main display indo
3OPEN button 38
4qa Receptor for the card remote
commander
5Volume adjust buttons
6DSPL/PTY (display mode change/
programme type) button
7Sub display indo
8MENU button
9
Z (eject) button 11
qs LIST button
qd OFF button*
9
qf MODE button
qg SOURCE (TUNER/TAPE/CD/MD) button
qh AF button 16, 18
qj Number buttons
During radio reception:
Preset number select
13, 14, 17, 33, 34
During tape playback:
(1) REP 12
During CD/MD playback:
(1) REP 28
(2) SHUF 28
5
OFF D-BASS
SEEK
PTY
SEEK
MENU LIST
SOUND ENTER
DISC
DISC
SOURCE
DSPL AF/TA MODE
VOLATT
OPEN/CLOSE
Location of controls
Refer to the pages listed for details.
1OFF button 9, 11
2MENU button 10, 12, 13, 14, 16, 18, 20,
24, 25, 27, 28, 29, 31, 33, 34, 36
3SOURCE (TUNER/TAPE/CD/MD) button
9, 11, 13, 14, 25, 26, 30, 32, 33
4</, (SEEK/AMS –/+) buttons
9, 10, 11, 12, 14, 16, 20, 23, 24, 25, 27, 28,
29, 31, 32, 34, 36
Automatic Music Sensor (./>)
11, 27
Manual search (m/M) 27
Seek 14
5SOUND button 23
6DSPL/PTY (display mode change/
programme type) button
19, 26, 27, 29, 36
7ATT (attenuate) button 23
8D-BASS button 24
9OPEN/CLOSE button 11
0LIST button 29, 30, 35
qa M/m (DISC/PRST +/–) buttons
9, 10, 12, 13, 14, 16, 18, 19, 20, 24, 25,
27, 28, 29, 30, 31, 32, 33, 34, 36
During radio reception:
Preset stations select 14
During CD/MD playback:
Disc change 27
qs ENTER button 10, 12, 13, 14, 16, 18, 19,
20, 24, 25, 27, 29, 30, 31, 33, 34, 35, 36
qd AF/TA button 16, 17, 18
qf MODE button
11, 12, 13, 14, 26, 30, 32, 33
During tape playback:
Playback direction change 11
During radio reception:
BAND select 13, 14
During CD/MD playback:
CD/MD unit select 26
qg VOL (Volume adjust) buttons
A unit turned off by pressing (OFF) for two
seconds cannot be operated with the card
remote commander unless (SOURCE) on the
unit is pressed or a cassette is inserted to
activate the unit first.
Card remote commander RM-X96
10
Tips
• You can use the convenient CT function to set
the clock automatically (page 20).
• When the D.Info mode is set to “on,” the time is
always displayed (except for some functions of
SA mode) (page 23).
Setting the clock
The clock uses a 24 hour digital indication.
Example: To set the clock to 10:08
1 Press (MENU), then M or m repeatedly
until “Clock” appears.
1 Press (ENTER).
The hour indication flashes.
2 Press M or m to set the hour.
3 Press ,.
The minute indication flashes.
4 Press M or m to set the minute.
2 Press (ENTER).
The clock starts.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

5
XR-M510
15 cm
Εγκατάσταση
Προφυλάξεις
• Εάν τοποθετήσετε αυτή τη συσκευή
µαζί µε άλλο εξοπλισµ της Sony,
είναι καλύτερα να τοποθετήσετε τη
συσκευή στην κάτ θέση.
• Πρέπει να υπάρχει µια απσταση
τουλάχιστον 15 εκ. µεταξύ της
υποδοχής κασέτας της συσκευής και
του µοχλού ταχυτήτ ν, ώστε να
υπάρχει επαρκής χώρος για την
εύκολη εισαγ γή της κασέτας.
Επιλέξτε τη θέση εγκατάστασης µε
προσοχή, ώστε η συσκευή να µην
εµποδίζει στην αλλαγή ταχυτήτ ν ή
άλλους χειρισµούς οδήγησης.
• Οταν η πρσοψη είναι ανοικτή, ένα
τµήµα της θα προεξέχει απ τη
συσκευή προς τα κάτ . Οταν
εγκαταστήσετε τη συσκευή,
βεβαι θείτε τι αυτ το τµήµα της
πρσοψης δεν παρεµποδίζεται ενώ
βρίσκεται σε ανοικτή θέση (για
παράδειγµα απ το σταχτοδοχείο).
• Επιλέξτε προσεκτικά τη θέση
εγκατάστασης έτσι ώστε η συσκευή
να µην παρεµβάλλεται στις συνήθεις
κινήσεις οδήγησης.
• Αποφύγετε την εγκατάσταση της
συσκευής σε σηµεία υποκείµενα σε
υψηλές θερµοκρασίες, π ς στον
ήλιο ή σε αεραγ γούς του
καλοριφέρ, ή σε σηµεία υποκείµενα
σε σκνη, βρ µιά ή υπερβολικές
δονήσεις.
• Για ασφαλή και σίγουρη
εγκατάσταση χρησιµοποιείτε µνο
τα παρεχµενα υλικά τοποθέτησης.
Ρύθµιση γωνίας τοποθέτησης
Ρυθµίστε τη γ νία τοποθέτησης σε
λιγτερο απ 20°.
Extended portion of the front panel.
Parte sobresaliente del panel frontal.
Utskjutande del av frontpanelen.
Parte extensível do painel frontal.
Προεξέχον τµήµα της πρσο ης.
8.5 mm
15.5 mm
Installation
Precautions
•If you mount other Sony equipment
with this unit, it is better to mount this
unit in the lower position.
•There must be a distance of at least 15
cm between the cassettes slot of the
unit and shift lever to insert cassette
easily. Choose the installation location
carefully so the unit does not interfere
with ear shiftin and other drivin
operations.
•When the front panel is open, a
portion of it will extend down from the
unit. When you install the unit, make
sure that this portion of the front panel
is not obstructed in its open position
(by the ashtray, for example).
•Choose the installation location
carefully so that the unit will not
interfere with normal drivin
operations.
•Avoid installin the unit in areas
subject to dust, dirt, excessive
vibration, or hi h temperatures, such
as in direct sunli ht or near heater
ducts.
•Use only the supplied mountin
hardware for a safe and secure
installation.
Mounting angle adjustment
Adjust the mountin an le to less than
20°.
Instalación
Precauciones
•Si monta otro equipo Sony con esta
unidad, es preferible montar esta
unidad en la posición más baja.
•Para que sea posible insertar la cinta
con facilidad, debe haber una
distancia de al menos 15 cm entre la
ranura de inserción de cintas de la
unidad y la palanca de cambios.
Instale la unidad en un lu ar que no
entorpezca las operaciones de cambio
de marchas o de conducción en
eneral.
•Cuando el panel frontal está abierto,
una parte de él sobresaldrá de la
unidad. Cuando instale la unidad,
compruebe que dicha parte del panel
frontal no queda obstruida en la
posición de apertura (debido al
cenicero, por ejemplo).
•Elija cuidadosamente el lu ar de
montaje de forma que la unidad no
interfiera las funciones normales de
conducción.
•Evite instalar la unidad donde pueda
quedar sometida a altas temperaturas,
como a la luz solar directa o al aire de
calefacción, o a polvo, suciedad, o
vibraciones excesivas.
•Para realizar una instalación se ura y
firme, utilice solamente la ferretería de
montaje suministrada.
Ajuste del ángulo de montaje
Ajuste el án ulo de montaje a menos de
20°.
Montering
Säkerhetsföreskrifter
•Om du monterar annan Sony-
utrustnin till denna enhet är det bäst
att montera denna enhet i det undre
lä et.
•För att du ska kunna sätta i och ta ut
bandet måste avståndet vara minst 15
cm mellan kassettfacket på enheten
och växelspaken. När du installerar
enheten väljer du en plats så att
enheten inte är i vä en när du kör.
•När frontpanelen är öppen befinner
si en liten del av den under enhetens
bottenplan. Se till att du installerar
enheten så att den här delen år fri
(från t.ex. askkoppen) när frontpanelen
är öppen.
•Var no a när du väljer var i bilen du
monterar bilstereon, så att den inte
sitter i vä en när du kör.
•Montera inte bilstereon där den utsätts
för värme,
t ex solsken eller varmluft, eller där
den utsätts för damm, smuts och/eller
vibrationer.
•Använd endast de medföljande
monterin stillbehören för att vara
säker på att bilstereon monteras på ett
säkert och korrekt sätt.
Tillåten monteringsvinkel
Monterin svinkeln får inte vara större
än 20 rader.
Instalação
Precauções
•É preferível montar este aparelho na
posição mais baixa, se quiser montar
simultaneamente outros equipamentos
da Sony.
•Para colocar com facilidade a cassete,
deve haver uma distância de pelo
menos 15 cm entre a ranhura de
introduçäo da cassete e a alavanca das
mudanças.
Escolha o local de instalaçäo de forma
a que o aparelho näo interfira com as
mudanças de velocidade ou com as
outras manobras de conduçäo.
•Quando o painel frontal estiver aberto,
pode puxar a parte extensível baixo.
Quando instalar a unidade, verifique
se essa parte do painel frontal não está
presa na posição aberta (pelo cinzeiro,
por exemplo).
•Escolha com cuidado um local
apropriado para a monta em do
aparelho, para que este não interfira
com as manobras necessárias à
condução do veículo.
•Evite instalar o aparelho onde possa
estar sujeito a altas temperaturas,
como em locais expostos directamente
à luz do sol, ao ar quente dos
aquecimentos, ou sujeitos a pó,
sujidade ou vibração excessiva.
•Para efectuar uma instalação se ura
utilize unicamente o hardware de
monta em fornecido.
Ajuste do ângulo de montagem
Ajuste o ân ulo de monta em a menos
de 20°.
23
Changing the sound and
display settings
The following items can be set:
Set (Setting)
•Clock (page 10).
•CT (Clock Time) (page 20).
•Beep — to turn the beep sound on or off.
•RM (Rotary Commander) — to change the
operative direction of the rotary commander.
— Select “norm” to use the rotary
commander as the factory set position.
— Select “rev” when you mount the rotary
commander on the right side of the
steering column.
•English/Spanish/Portuguese/Swedish — to
change the display language to English,
Spanish, Portuguese or Swedish.
Dis (Display)
•D.Info (Dual Information) — to display the
clock and the play mode simultaneously (on),
or to display the information alternately (off).
•SA (Spectrum Analyzer) — to change the
display pattern of the equalizer display
(page 25).
•Dimmer — to change the brightness of the
display (When the Illumination terminal
connected).
— Select “on” to dim the display.
— Select “off” to deactivate Dimmer.
•Contrast — to adjust the contrast if the
indications in the display are not
recognisable because of the unit’s installed
position.
•M.Dspl (Motion Display) — to turn the
motion display on or off.
•A.Scrl (Auto Scroll) (page 27).
continue to next page t
24
1Press (MENU).
2Press Mor mrepeatedly until the desired
item appears.
Each time you press m, the item changes as
follows:
Example
Clock tCT tBeep tRM tEnglish/
Spanish/Portuguese/Swedish tD.Info tSA
tDimmer tContrast tM.Dspl*
1
t A.Scrl*
2
*
1
When no CD or MD is playing, this item will
not appear.
*
2
When the radio is off, or when no tape, CD,
or MD is playing, this item will not appear.
Note
The displayed item will differ depending on the
source.
Tip
You can easily switch among categories (“Set,”
“Snd” (Sound), “P/M” (Play Mode) and “Dis”) by
pressing Mor mfor two seconds.
3Press ,to select the desired setting
(Example: on or off).
4Press (ENTER).
After the mode setting is complete, the
display returns to normal playback mode.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

6
XR-M510
Συνδέσεις
Προσοχή
• Αυτή η συσκευή έχει σχεδιαστεί να
λειτουργεί µνο µε τροφοδοσία απ
µπαταρία αυτοκινήτου 12 V DC µε
αρνητική γεί ση.
• Προσέξτε να µην µαγκώσετε κάποιο
καλώδιο µεταξύ του σώµατος του
αυτοκινήτου και κάποιας βίδας ή
της συσκευής, ή µεταξύ
οποι νδήποτε κινούµεν ν
τµηµάτ ν π ς για παράδειγµα στη
ράγα του καθίσµατος.
• Συνδέστε το καλώδιο τροφοδοσίας
8 στη συσκευή και τα ηχεία πριν το
συνδέσετε στην υποδοχή
βοηθητικής τροφοδοσίας.
•Συνδέστε λα τα καλώδια γείωσης
σε µια κοινή γη.
• Συνδέστε το κίτρινο καλώδιο σε ένα
ελεύθερο κύκλ µα του
αυτοκινήτου µε ονοµαστική τιµή
έντασης µεγαλύτερη της
αναγραφµενης στην ασφάλεια της
συσκευής. Αν συνδέσετε τη
συσκευή αυτή σε συνδυασµ µε
άλλες στερεοφ νικές συσκευές
ήχου, θα πρέπει η ονοµαστική τιµή
της έντασης του κυκλώµατος του
αυτοκινήτου που θα συνδεθεί να
είναι µεγαλύτερη απ το άθροισµα
τ ν εντάσε ν τ ν επιµέρους
ασφαλειών. Αν δεν υπάρχει
κύκλ µα στο αυτοκίνητο µε τσο
µεγάλη ονοµαστική τιµή έντασης,
συνδέστε τη συσκευή απ’ ευθείας
στην µπαταρία. Αν δεν υπάρχει
ελεύθερο διαθέσιµο κύκλ µα για τη
σύνδεση της συσκευής, συνδέστε
τη συσκευή σε κάποιο κύκλ µα
µεγαλύτερης ονοµαστικής τιµής
έντασης απ την αναγραφµενη
στην ασφάλεια της συσκευής, µε
τέτοιο τρπο ώστε αν καεί η
ασφάλεια της συσκευής να µην
αποκοπεί άλλο κύκλ µα.
Προειδοποίηση για την
εγκατάσταση σε
αυτοκίνητο χωρίς θέση
ACC (βοηθητική) στον
διακπτη ανάφλεξης
Βεβαιωθείτε τι πιέσατε το πλήκτρο
(OFF) της συσκευής για δύο
δευτερλεπτα ώστε να
απενεργοποιήσετε την ένδειξη του
ρολογιού αφού σβήσετε τη µηχανή
του αυτοκινήτου.
Αν πιέσετε το πλήκτρο (OFF)
στιγµιαία µνο, η ένδειξη του
ρολογιού δεν απενεργοποιείται και
έτσι προκαλείται φθορά στην
µπαταρία του αυτοκινήτου.
Connections
Cautions
•This unit is desi ned for ne ative earth
12 V DC operation only.
•Be careful not to pinch any wires
between a screw and the body of the
car or this unit or between any movin
parts such as the seat railin , etc.
•Connect the power connectin cord 8
to the unit and speakers before
connectin it to the auxiliary power
connector.
•Run all earth wires to a common
earth point.
•Connect the yellow cord to a free car
circuit rated hi her than the unit’s fuse
ratin . If you connect this unit in
combination with other stereo
components, the car circuit they are
connected to must be rated hi her than
the sum of the individual components’
fuse ratin . If there are no car circuits
rated as hi h as the unit’s fuse ratin ,
connect the unit directly to the battery.
If no car circuits are available for
connectin this unit, connect the unit
to a car circuit rated hi her than the
unit’s fuse ratin in such a way that if
the unit blows its fuse, no other circuits
will be cut off.
Conexiones
Precauciones
•Esta unidad ha sido diseñada para
alimentarse con 12 V CC, ne ativo a
masa, solamente.
•Ten a cuidado de no atrapar nin ún
cable entre al ún tornillo y la
carrocería del automóvil o esta unidad
o entre las partes móviles, como por
ejemplo los raíles del asiento, etc.
•Conecte el cable de conexión de
alimentación 8 a la unidad y los
altavoces antes de conectarlo al
conector de alimentación auxiliar.
•Conecte todos los conductores de
puesta a masa a un punto común.
•Conecte el cable amarillo a un circuito
libre del automóvil de potencia
nominal superior a la del fusible de la
unidad. Si conecta esta unidad en
combinación con otros componentes
estéreo, la potencia nominal del
circuito del automóvil a los que dichos
componentes estén conectados debe
ser superior a la suma de la potencia
nominal del fusible de los
componentes. Si no existen circuitos de
automóvil de potencia nominal tan
alta como la del fusible de la unidad,
conecte ésta directamente a la batería.
Si no hay circuitos de automóvil
disponibles para conectar esta unidad,
conecte la misma a un circuito de
automóvil de potencia nominal
superior a la del fusible de la unidad
de forma que no se desactiven otros
circuitos si el fusible de dicha unidad
se funde.
Anslutning
Säkerhetsföreskrifter
•Denna bilstereo är endast avsedd för
anslutnin till ett ne ativt jordat, 12 V
bilbatteri.
•Var no a med att in a kablar kläms
mellan nå on skruv eller att de blir
klämda mellan rörli a delar som t.ex.
bilsätet.
•Anslut strömkabeln 8 till enheten och
hö talarna innan du ansluter den till
den yttre strömanslutnin en.
•Dra samtliga jordledningar till en
och samma jordningspunkt.
•Anslut den ula kabeln till en ledi
bilkrets med ett hö re amperetal än
enhetens. Om du kopplar både denna
enhet och andra stereokomponenter till
en och samma bilkrets, måste den
bilkrets de kopplas till ha en hö re
ampere än summan av de enskilda
delarnas amperestyrka. Om det inte
finns nå ra bilkretsar med en så hö
amperestyrka som enhetens ska du
ansluta enheten direkt till batteriet. Om
in a bilkretsar finns för anslutnin till
enheten ska du ansluta enheten till en
bilkrets med ett hö re amperetal än
enhetens säkrin , så att det är denna
som år i stället för bilens.
Ligações
Cuidado
•Este aparelho foi concebido para
funcionar somente com corrente
contínua de 12 V com ne ativo à
massa.
•Tenha cuidado para que os fios não
fiquem entalados entre os parafusos e
a carroçaria do automóvel ou a caixa
do aparelho, nem entre as peças
móveis, por exemplo, as calhas dos
bancos, etc.
•Li ue o cabo de alimentação de
corrente 8 ao aparelho e aos
alifalantes antes de o li ar ao conector
de corrente auxiliar.
•Ligue todos os cabos de massa num
ponto de massa comum.
•Li ue o cabo amarelo a um circuito
eléctrico livre do automóvel, cuja
potência nominal seja superior à dos
fusíveis do aparelho. Se li ar este
aparelho em série com outros
componentes estéreo, a potência
nominal do circuito eléctrico do
automóvel onde os li ar tem de ser
superior à soma da potência nominal
dos fusíveis de todos os componentes
individuais. Se não houver nenhum
circuito eléctrico do automóvel com
uma potência nominal tão elevada
como a dos fusíveis do aparelho, li ue-
o directamente à bateria. Se não estiver
disponível nenhum circuito eléctrico
do automóvel para li ação deste
aparelho, li ue-o a um circuito
eléctrico do automóvel com uma
potência nominal superior à dos
fusíveis do aparelho, de tal modo que,
se o aparelho rebentar os fusíveis
respectivos, nenhum outro circuito seja
cortado.
Warning when installing in
a car without ACC
(accessory) position on the
ignition key switch
Be sure to press (OFF) on the unit for
two seconds to turn off the clock
display after turned off the engine.
When you press (OFF) momentarily, the
clock display does not turn off and this
causes battery wear.
Advertencia sobre la
instalación en un
automóvil que no
disponga de posición ACC
(accesorios) en el
interruptor de la llave de
encendido
Asegúrese de pulsar (OFF) en la
unidad durante dos segundos para
desactivar la indicación del reloj una
vez apagado el motor.
Si pulsa (OFF) momentáneamente, la
indicación del reloj no se desactivará y
esto causará el des aste de la batería.
Aviso sobre a instalação
num automóvel sem
posição ACC (acessórios)
na chave de ignição
Verifique se carregou em (OFF) no
aparelho durante dois segundos para
desactivar o visor do relógio depois de
ter desligado o motor.
Se carre ar li eiramente em (OFF), não
desactiva o visor do reló io o que
provoca o des aste da bateria.
Var försiktig när du gör
installationen i en bil där
tändningslåset saknar
tillbehörsläge (ACC)
Glöm inte att trycka på (OFF) på
enheten under två sekunder för att
stänga av klockans teckenfönster
efter det att du har stängt av motorn.
Om du bara trycker på (OFF) ett kort
ö onblick slocknar inte klockans
teckenfönster vilket kan leda till att
batteriet laddas ur.
124
Εγκατάσταση στο ταµπλ
Bend these claws outward for a
tight fit, if necessary.
Si es necesario, doble estas uñas
hacia afuera para que encaje
firmemente.
För att få en tät passning böj
dessa flikar vid behov.
Se necessário, dobre as unhas
para prender melhor.
Αν χρειαστεί, λυγίστε αυτές τις
προεξοχές προς τα έξω για µια
πιο ασφαλή εγκατάσταση.
5
7
75
5
72
3
4
1
Fire wall
Panel cortafuegos
Brandsäker mellanvägg
Painel corta-fogo
Αλεξίπυρο χώρισµα
Dashboard
Salpicadero
Instrumentbräda
Tablier
Ταµπλ
1With the UP marking up
Con la marca UP hacia arriba
Med märkningen UP vänd uppåt
Com a marca UP para cima
Mε την ένδειξη UP προς τα επάνω
Σηµείωση
Για να µην παρουσιαστούν δυσλειτουργίες,
εγκαταστήστε µνο µε τις βίδες 5 που
χορηγούνται.
3
Installation in the
dashboard Instalación en el salpicadero Montera på instrumentbrädan Instalação no tablier
Note
To prevent malfunction, install only with
the supplied screws 5.
Nota
Para evitar fallos de funcionamiento, realice
la instalación únicamente con los tornillos
suministrados 5.
Observera
Använd bara de medföljande skruvarna 5,
så undviker du onödiga fel.
Nota
Para evitar avarias, instale o aparelho
apenas com os parafusos fornecidos 5.
Πλήκτρο Επαναρύθµισης
(Reset)
;ταν ολοκληρ θούν η εγκατάσταση και οι
συνδέσεις, θυµηθείτε να πιέσετε το πλήκτρο
επαναρύθµισης µε ένα στυλ.
Caution
Cautionary notice for handlin the bracket 1.
Handle the bracket carefully to avoid injurin
your fin ers.
Precaución
Advertencia sobre la manipulación del soporte
1.
Ten a mucho cuidado al manipular el soporte
para evitar posibles lesiones en los dedos.
Varning
Att observera an ående konsolen 1.
Hantera konsolen med största aktsamhet så att
du inte skadar fin rarna.
Reset button
When the installation and connections are
complete, be sure to press the reset button with a
ballpoint pen, etc.
Botón de restauración
Cuando finalice la instalación y las conexiones,
cerciórese de pulsar el botón de restauración con
un bolí rafo, etc.
Nollställningsknappen
Kom ihå att använda en penna eller nå ot annat
spetsi t föremål för att trycka på
nollställnin sknappen när anslutnin en och
monterin en är klar.
Botão de reinicialização
Quando terminar a instalação e as li ações, não
se esqueça de carre ar no botão de reinicialização
com a ponta de uma caneta, esfero ráfica, etc.
Cuidado
Aviso sobre as precauções a tomar no
manuseamento do suporte 1.
Pe ue no suporte com cuidado para não ma oar
os dedos.
Προσοχή
Προειδοποίηση για το χειρισµ του πλαισίου
1.
Χειρίζεστε το πλαίσιο προσεκτικά προς
αποφυγή τραυµατισµού τ ν δαχτύλ ν σας.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

7
XR-M510
Σηµειώσεις σχετικά µε
παραδείγµατα σύνδεσης
Σηµειώσεισ σχετικά µε τα καλώδια
ελέγχου
• To καλώδιο ελ γχου της ηλεκτρικής
κεραίας (µπλε) τροφοδοτείται µε +12 V
DC κάθε φορά που ενεργοποιείτε το
ραδιφωνο ή ταν ενεργοποιείτε τις
λειτουργίες ΑΤΑ (Αυτµατη
Ενεργοποίηση ∆ κτη), ΑF (Eναλλακτική
Συχντητα), ΤΑ (Ανακοινώσεις για την
Κυκλοφορία).
• ∆εν µπορεί να χρησιµοποιηθεί
ηλεκτρική κεραία χωρίς κουτί ρελ
µε τη συσκευή αυτή.
• Αν το αυτοκίνητ σας διαθ τει
ενσωµατωµ νη κεραία FM/MW/LW
στο πίσω/πλαϊν τζάµι, χρειάζεται
να συνδ σετε το καλώδιο ελ γχου
της ηλεκτρικής κεραίας (µπλε) ή το
καλώδιο βοηθητικής τροφοδοσίας
(κκκινο) στην υποδοχή
τροφοδοσίας του ενισχυτή της
υπάρχουσας κεραίας. Για
περισστερες λεπτοµ ρειες,
συµβουλευθείτε το κατάστηµα
πώλησης.
Προειδοποίηση
Αν διαθ τετε ηλεκτρική κεραία χωρίς
κουτί ρελ , η σύνδεση της συσκευής
αυτής µε το παρεχµενο καλώδιο
τροφοδοσίας 8 µπορεί να
προκαλ σει ζηµιά στην κεραία.
Σύνδεση για τη διατήρηση τησ µνήµησ
Μετά τη σύνδεση του κίτρινου καλωδίου
τροφοδοσίας, το κύκλωµα της µνήµης θα
τροφοδοτείται συνεχώς ακµα και ταν
γυρίσετε το κλειδί ανάφλεξης στη θ ση
off.
Σηµειώσεισ για τη σύνδεση των ηχείων
• Πριν συνδ σετε τα ηχεία,
απενεργοποιήστε τη συσκευή.
• Χρησιµοποιήστε ηχεία µε σύνθετη
αντίσταση απ 4 ως 8 ohm, και
ικανοποιητική ισχύ. Σ’ αντίθετη
περίπτωση, τα ηχεία µπορεί να
καταστραφούν.
• Μην συνδ ετε τους ακροδ κτες του
συστήµατος των ηχείων στο σασί
του αυτοκινήτου, και µην συνδ ετε
τους ακροδ κτες του δεξιού ηχείου
µε αυτούς του αριστερού ηχείου.
• Μην προσπαθήσετε να συνδ σετε
τα ηχεία παράλληλα.
• Μην συνδ σετε ενεργά ηχεία (µε
ενσωµατωµ νους ενισχυτ ς) στις
υποδοχ ς των ηχείων της
συσκευής. Αν κάνετε κάτι τ τοιο
µπορεί να προκαλ σετε ζηµιά στα
ενεργά ηχεία. Εποµ νως,
βεβαιωθείτε τι συνδ ετε παθητικά
ηχεία στις υποδοχ ς αυτ ς.
Notes of connection
example
Notes on the control leads
•The power aerial control lead (blue)
supplies +12 V DC when you turn on the
tuner or when you activate the ATA
(Automatic Tuner Activation), AF
(Alternative Frequency) or the TA (Traffic
Announcement) function.
•A power aerial without a relay box cannot
be used with this unit.
•When your car has a built-in FM/MW/LW
aerial in the rear/side glass, it is necessary
to connect the power aerial control lead
(blue) or the accessory power input lead
(red) to the power terminal of the existing
aerial booster. For details, consult your
dealer.
Warning
If you have a power aerial without a relay
box, connecting this unit with the supplied
power connecting cord 8may damage the
aerial.
Memory hold connection
When the yellow power input lead is
connected, power will always be supplied to
the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
•Before connecting the speakers, turn the
unit off.
•Use speakers with an impedance of 4 to 8
ohms, and with adequate power handling
capacities. Otherwise, the speakers may be
damaged.
•Do not connect the terminals of the
speaker system to the car chassis, and do
not connect the terminals of the right
speaker with those of the left speaker.
•Do not attempt to connect the speakers in
parallel.
•Do not connect any active speakers (with
built-in amplifiers) to the speaker
terminals of the unit. Doing so may
damage the active speakers. Be sure to
connect passive speakers to these
terminals.
Notas de ejemplo de
conexiones
Notas sobre cables de control
• El cable de control (azul) de la antena
motorizada suministra + 12 V CC al activar
el sintonizador o la función ATA
(activación automática del sintonizador),
AF (frecuencias alternativas) o TA
(anuncios de tráfico).
• Con esta unidad no podrá utilizarse una
antena motorizada sin caja de relés.
• Si el automóvil dispone de antena de FM/
MW/LW incorporada en el cristal trasero/
lateral, será necesario conectar el cable de
control de antena motorizada (azul) o el
cable de entrada de alimentación
accesoria (rojo) al terminal de potencia
del amplificador de antena existente. Para
más información, consulte con el
proveedor.
Advertencia
Si dispone de una antena motorizada sin
dispositivo de relé, la conexión de esta
unidad con el cable de conexión de
alimentación 8suministrado puede dañar
la antena.
Conexión para protección de la memoria
Si conecta el cable de entrada de
alimentación amarillo, el circuito de la
memoria recibirá siempre alimentación,
incluso aunque ponga la llave de encendido
en la posición de apagado.
Notas sobre la conexión de los altavoces
•Antes de conectar los altavoces,
desconecte la alimentación de la unidad.
•Utilice altavoces con una impedancia de 4
a
8 ohmios, y con la potencia máxima
admisible adecuada, ya que de lo
contrario podría dañarlos.
•No conecte los terminales del sistema de
altavoces al chasis del automóvil, ni los
del altavoz izquierdo a los del derecho.
•No intente conectar los altavoces en
paralelo.
•No conecte altavoces activos (con
amplificadores incorporados) a los
terminales de altavoces de la unidad. Si lo
hiciese, podría dañar tales altavoces. Por
lo tanto, cerciórese de conectar altavoces
pasivos a estos terminales.
Att observera angående
anslutningsexemplen
Att observera angående de olika
styrkablarna
•Motorantennens styrkabel (blå) leder + 12
volts likström när kanalväljaren slås på
eller när radiomottagningsautomatik
ATA, mottagning av alternativa
frekvenser AF eller mottagning av
trafikmeddelanden TA aktiverats.
•En motorantenn utan styrrelädosa kan
inte anslutas till denna bilstereo.
•Om bilen har en FM/MW/LW-antenn som
är inbyggd i sido- eller bakrutan, måste du
ansluta motorantennens styrkabel (blå)
eller tilbehörsströmkabeln (röd) till
strömterminalen på antennförstärkaren.
Din återförsäljare kan ge dig mer
information.
Varning
Om du har en motorantenn utan relädosa
kan antennen skadas om du ansluter
enheten med den medföljande strömkabeln
8.
Anslutning för minnesstöd
När du anslutit den gula, ingående
strömkabeln försörjs minneskretsen med
ström hela tiden, även när tändlåset slås
ifrån.
Att observera angående högtalarnas
anslutning
•Slå av bilstereon innan du ansluter
högtalarna.
•Anslut endast högtalare, vars impedans
varierar från 4 till 8 ohm och som har
tillräcklig effekthanteringskapacitet för
att skydda högtalarna mot skador.
•Anslut inte något av högtalaruttagen till
bilens chassi. Anslut inte heller uttagen på
höger högtalare till uttagen på vänster
högtalare.
•Anslut inte högtalarna parallellt.
•Anslut inte aktiva högtalare (med
inbyggda slutsteg) till bilstereons
högtalaruttag, eftersom de kan skada de
aktiva högtalarna. Var noga med att bara
ansluta passiva högtalare till dessa uttag.
Notas sobre o exemplo de
ligação
Notas sobre os fios de controlo
• O fio de controlo da antena eléctrica
(azul) fornece +12 V CC quando ligar o
sintonizador ou quando activar as funções
ATA (Activação automática do
sintonizador), AF (frequência alternativa)
ou TA (Informações de trânsito).
• Não pode utilizar uma antena eléctrica
sem caixa de relé com este aparelho.
•Se o seu automóvel tiver uma antena de
FM/MW/LW montada no vidro traseiro/
lateral, tem de ligar o fio de controlo da
antena eléctrica (azul) ou o fio de entrada
de alimentação para os acessórios
(vermelho) ao terminal de alimentação do
intensificador do sinal da antena
existente.
Advertência
Se a antena eléctrica não tiver uma caixa de
relé, o facto de ligar este aparelho com o
cabo de alimentação 8fornecido, pode
provocar danos na antena.
Ligação para alimentação contínua da
memória
Quando o fio amarelo de entrada de
alimentação for ligado, os circuitos de
memória ficarão com alimentação continua,
mesmo se a chave de ignição estiver
desligada.
Notas sobre a ligação dos altifalantes
•Antes de ligar os altifalantes, desligue o
aparelho.
•Utilize altifalantes com impedância de 4 a
8 ohm, e com potência máxima admissível
adequada. Caso contrário, os altifalantes
poderão sofrer avarias.
•Não ligue os terminais do sistema de
altifalantes ao chassis do automóvel, e
não ligue os terminais do altifalante
direito aos terminais do altifalante
esquerdo.
•Não tente ligar os altifalantes em
paralelo.
•Não ligue nenhum sistema de altifalantes
activos (com amplificadores incorporados)
aos terminais dos altifalantes do aparelho.
Caso o faça, poderá avariar o sistema de
altifalantes activos. Portanto, não se
esqueça de ligar altifalantes passivos a
estes terminais.
Power connection diagram
Auxiliary power connector may vary
dependin on the car. Check your car’s
auxiliary power connector dia ram to
make sure the connections match
correctly. There are three basic types
(illustrated below). You may need to
switch the positions of the red and
yellow leads in the car stereo’s power
connectin cord.
After matchin the connections and
switched power supply leads correctly,
connect the unit to the car’s power
supply. If you have any questions and
problems connectin your unit that are
not covered in this manual, please
consult the car dealer.
Diagrama de conexión de
alimentación
El conector de alimentación auxiliar
puede variar en función del automóvil.
Compruebe el dia rama del conector de
alimentación auxiliar del automóvil para
ase urarse de que las conexiones
coinciden correctamente. Existen tres
tipos básicos, ilustrados a continuación.
Es posible que sea necesario cambiar las
posiciones de los cables rojo y amarillo
del cable de conexión de alimentación
del sistema estéreo del automóvil.
Después de hacer coincidir
correctamente las conexiones y los cables
de alimentación conmutada, conecte la
unidad al suministro de alimentación
del automóvil. Si desea realizar al una
consulta o solucionar al ún problema
referentes a la conexión de la unidad que
no aparezcan en este manual, consulte
con el concesionario automovilístico.
Strömanslutningsschema
Typen av yttre strömanslutnin varierar
från bil till bil. Kontrollera schemat till
strömanslutnin en så att du ansluter på
rätt sätt. Det finns tre rundlä ande
anslutnin styper (visas nedan). Du kan
behöva skifta plats på bilstereons röda
och ula strömförsörjnin skablar.
Koppla kablarna för kontinuerli
respektive switchad strömförsörjnin på
rätt sätt och anslut sedan enheten till
bilens strömanslutnin . Om du får
problem eller har frå or som inte
besvaras i den här bruksanvisnin en kan
du kontakta bilåterförsäljaren.
Diagrama de ligação de
corrente
O conector auxiliar de corrente pode
variar de carro para carro. Verifique o
dia rama do conector auxiliar de
corrente para se certificar de que as
li ações estão bem feitas. Existem três
tipos de conectores (ilustrados abaixo).
Depois de fazer a correspondência entre
as li ações e os terminais de alimentação
de corrente comutada, li ue o aparelho à
fonte de alimentação do carro. Se tiver
al uma dúvida ou problema relacionado
com o aparelho que não esteja incluído
neste manual, consulte o concessionário.
∆ιάγραµµα Σύνδεσης
Τροφοδοσίας
Η υποδοχή βοηθητικής τροφοδοσίας
µπορεί να διαφέρει ανάλογα µε το
αυτοκίνητο. Ελέγξτε το διάγραµµα
σύνδεσης της υποδοχής βοηθητικής
τροφοδοσίας του αυτοκινήτου σας
ώστε να βεβαι θείτε τι οι συνδέσεις
έχουν γίνει σ στά. Υπάρχουν τρεις
βασικοί τύποι συνδέσε ν (εικονίζονται
παρακάτ ). Μπορεί να χρειαστεί να
εναλλάξετε τις θέσεις του κκκινου
και του κίτρινου καλ δίου του αγ γού
τροφοδοσίας του στερεοφ νικού
συστήµατος του αυτοκινήτου σας.
Μετά την εκτέλεση τ ν συνδέσε ν
και τη σ στή σύνδεση τ ν καλ δί ν
της διακοπτµενης τροφοδοσίας,
συνδέστε τη συσκευή στην µπαταρία
του αυτοκινήτου. Για οποιαδήποτε
ερώτηση ή πρβληµα στη σύνδεση της
συσκευής που δεν καλύπτεται απ το
παρν εγχειρίδιο, παρακαλούµε
συµβουλευθείτε τον αντιπρσ πο του
αυτοκινήτου σας.
Auxiliary power connector
Conector de alimentación auxiliar
Yttre strömanslutning
Conector de corrente auxiliar
Υποδοχή βοηθητικής τροφοδοσίας
4
7
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Red
Rojo
Röd
Vermelho
Κκκινο
continuous power supply
suministro de alimentación continua
kontinuerlig strömförsörjning
alimentação de corrente contínua
συνεχής τροφοδοσία
switched power supply
suministro conmutado de alimentación
switchad strömförsörjning
alimentação de corrente comutada
διακοπτµενη τροφοδοσία
the car without ACC position
automóvil sin posición ACC
bil utan ACC-läge
o carro sem posição ACC
αυτοκίνητο χωρίς θέση ACC
4
7
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Red
Rojo
Röd
Vermelho
Κκκινο
switched power supply
suministro conmutado de alimentación
switchad strömförsörjning
alimentação de corrente comutada
διακοπτµενη τροφοδοσία
continuous power supply
suministro de alimentación continua
kontinuerlig strömförsörjning
alimentação de corrente contínua
συνεχής τροφοδοσία
Red
Rojo
Röd
Vermelho
Κκκινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Red
Rojo
Röd
Vermelho
Κκκινο
Red
Rojo
Röd
Vermelho
Κκκινο
Red
Rojo
Röd
Vermelho
Κκκινο
Red
Rojo
Röd
Vermelho
Κκκινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Red
Rojo
Röd
Vermelho
Κκκινο
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

8
XR-M510
CD/MD changer
Cambiador de CD/MD
CD/MD-skivväxlare
Permutador CD/MD
CD/MD changer
Power amplifier
Amplificador de potencia
Effektförstärkare
Amplificador de potência
Τελικς ενισχυτής
Front speaker
Altavoz delantero
Främre högtalare
Altifalante dianteiro
Εµπρς ηχείο
Rear speaker
Altavoz trasero
Bakre högtalare
Altifalante traseiro
Πίσω ηχείο
Equipo utilizado en las
ilustraciones (no suministrado) Utrustning som visas i illustrationer (medföljer inte) Equipamento utilizado nas ilustrações (não fornecido)
∆ιάγραµµα συνδέσεων
Χρησιµοποιούµενος εξοπλισµς σε
εικνες (δεν παρέχεται)
AB
BUS
AUDIO IN AUDIO
OUT FRONT
BUS
CONTROL IN AUDIO OUT
REAR
BUS CONTROL IN
BUS AUDIO IN BUS AUDIO IN
BUS CONTROL IN
C
BUS CONTROL IN
AUDIO OUT REAR
Digital equalizer pre-amplifier
Preamplificador ecualizador
digital
Digital förförstärkare med
equaliser
Pré-amplificador equalizador
digital
Ψηφιακς ισοσταθµιστής
προενισχυτής
XDP-210EQ * , XDP-4000X *
D
DAB tuner unit
Sintonizador DAB
DAB-tunerenhet
Sintonizador DAB
Συσκευή δέκτη DAB
XT-100DAB*
Source selector*
Selector de fuente*
Väljare för ljudkälla*
Selector de fonte*
Επιλογέας πηγής*
For connecting two or more CD/MD
changers, the source selector XA-C30
(optional) is necessary.
Si desea conectar dos o más cambiadores,
necesitará el selector de fuente XA-C30
(opcional).
För anslutning av två eller flera växlare
krävs väljarna XA-C30 (tillval). Para ligar um ou mais permutadores, é necessário o selector de fonte XA-C30
(opcional).
Για τη σύνδεση δύο ή περισσοτ ρων CD/
MD changer, απαιτείται επιλογ ας πηγής
XA-C30 (προαιρετικς).
When connecting a digital equalizer pre-amplifier
(XDP-210EQ, XDP-4000X)
• Use an optional exterior amplifier. The built-in
amplifier of this unit can not be used in this case. For
details, refer to the Installation/Connections manual
XDP-210EQ, XDP-4000X.
• For details about the connection, refer to the
Instllation/Connections manual XDP-210EQ, XDP-
4000X. (not supplied)
Si conecta un preamplificador ecualizador digital
(XDP-210EQ, XDP-4000X.)
• Utilice un amplificador opcional externo. El
amplificador incorporado de esta unidad no puede
utilizarse en este caso. Para más información, consulte
el manual de instalación/conexiones de la unidad XDP-
210EQ, XDP-4000X.
• Para obtener información detallada sobre la conexión,
consulte el manual de instalación/conexiones de la
unidad XDP-210EQ, XDP-4000X. (no suministrada)
När du ansluter en digital förförstärkare med equaliser
(XDP-210EQ, XDP-4000X.)
• Använd en valfri extern förstärkare. Den inbyggda
förstärkaren kan inte användas i detta fall. Mer
information finns i Montering/Anslutninghandboken
XDP-210EQ, XDP-4000X.
• Mer information om hur du ansluter utrustning finns i
Montering/Anslutninghandboken
XDP-210EQ, XDP-4000X. (medföljer inte)
Se ligar um pré-amplificador equalizador digital
(XDP-210EQ, XDP-4000X.)
• Utilize um amplificador exterior opcional. O
amplificador integrado neste aparelho não pode
ser utilizado neste caso. Para obter mais
informações, consulte o manual de Instalação/
Ligações XDP-210EQ, XDP-4000X.
• Para obter mais informações sobre a ligação,
consulte o manual de Instalação/ Ligações do
XDP-210EQ, XDP-4000X. (não fornecido)
ταν συνδέετε έναν ψηφιακ ισοσταθµιστή
προενισχυτή (XDP-210EQ, XDP-4000X)
•Χρησιµοποιείτε ναν προαιρετικ εξωτερικ
ενισχυτή. Σε αυτή την περίπτωση δεν µπορεί να
χρησιµοποιηθεί ο ενσωµατωµ νος ενισχυτής
αυτής της συσκευής. Για περισστερες
λεπτοµ ρειες, δείτε το εγχειρίδιο
Εγκατάστασης/Συνδ σεων XDP-210EQ,
XDP-4000X
•Για περισστερες λεπτοµ ρειες σχετικά µε τη
σύνδεση, δείτε το εγχειρίδιο Εγκατάστασης/
Συνδ σεων XDP-210EQ, XDP-4000X (δεν
παρ χεται)
Note
Be sure to connect the earth cord before
connecting the amplifier.
Nota
Asegúrese de conectar primero el cable de puesta a
masa antes de realizar la conexión al amplificador.
Obsevera
Var noga med att först ansluta jorden, innan du
ansluter förstärkaren.
Nota
Antes de fazer a ligação ao amplificador tem de ligar
primeiro o cabo de ligação à massa.
Σηµείωση
Βεβαιωθείτε τι συνδ σατε πρώτα να καλώδιο
γείωσης, πριν συνδ σετε τον ενισχυτή.
*not supplied
no suministrado
medföljer inte
não fornecido
δεν παρ χεται
*not supplied
no suministrado
medföljer inte
não fornecido
δεν παρ χεται
*not supplied
no suministrado
medföljer inte
não fornecido
δεν παρ χεται
Connection diagram Diagrama de conexiones Kopplingsschema Diagrama de ligações
Equipment used in illustrations
(not supplied)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

9
XR-M510
Exemplo de ligações
*
1
Nota referente à ligação da antena
Se a antena do automóvel for uma
antena de tipo ISO (International
Organization for Standardization), utilize
o adaptador fornecido 6para fazer a
ligação respectiva.
Ligue primeiro a antena do automóvel ao
adaptador fornecido e depois à ficha tipo
jack de antena do sistema principal.
*
2
Cabo de terminais RCA (não fornecido)
Anslutningarna enligt
exemplet
*
1
Angående antennanslutning
Om motorantennen är av ISO-typ
(International Organization for
Standardization), använder du
medföljande adapter 6för att ansluta
den.
Anslut först motorantennen till
medföljande adapter och därefter till
antennuttaget på huvudenheten.
*
2
Kabel med RCA-kontakter (medföljer
inte)
Ejemplo de conexiones
*
1
Nota sobre la conexión de la antena
Si la antena del automóvil es del tipo ISO
(International Organization for
Standardization), emplee el adaptador
suministrado 6para conectarla.
En primer lugar, conecte la antena del
automóvil al adaptador suministrado y, a
continuación, a la toma de antena de la
unidad principal.
*
2
Cable con clavijas RCA (no suministrado)
Connection example
*
1
Note for the aerial connecting
If your car aerial is an ISO (International
Organisation for Standardisation) type,
use the supplied adaptor 6to connect it.
First connect the car aerial to the
supplied adaptor, then connect it to the
aerial jack of the master unit.
*
2
RCA pin cord (not supplied)
Παράδειγµα σύνδεσης
*
1
Σηµείωση σχετικά µε τη σύνδεση τησ
κεραίασ
Αν η κεραία του αυτοκινήτου σας είναι
τύπου ISO (εγκεκριµ νη απ το ∆ιεθνή
Οργανισµ Τυποποίησης),
χρησιµοποιήστε τον παρεχµενο
προσαρµογ α 6 για να τη συνδ σετε.
Συνδ στε την κεραία του αυτοκινήτου
πρώτα στον παρεχµενο προσαρµογ α,
και στη συν χεια στην υποδοχή κεραίας
της κυρίως συσκευής.
*
2
Καλώδιο βύσµατοσ RCA (δεν παρέχεται)
6
AMP REM
BUS AUDIO IN AUDIO OUT FRONT
BUS CONTROL IN
AUDIO OUT REAR
REMOTE IN
8
ATT
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
Maximal strömtillförsel 0,3 A
Corrente máxima de 0,3 A
Μέγιστο ρεύµα τροφοδοσίας 0,3 A
to the interface cable of a car telephone
al cable de interfaz de un teléfono para automóvil
till mobiltelefonens gränssnittskabel
Ao cabo de interface de um telefone para automóvel
προς το καλώδιο διασύνδεσης ενς τηλεφώνου
αυτοκινήτου
to a car’s speaker connector
a un conector de altavoces del automóvil
till bilens högtalaranslutning
ao conector de um altifalante do automóvel
προς την υποδοχή ηχείου του αυτοκινήτου
Light blue
Azul celeste
Ljusblå
Azul claro
Ανοικτ µπλε
Blue/white striped
Con raya azul/blanca
Blå/vit-randig
Azul com listras brancas
Μπλε/λευκ µε ρίγες
from car aerial*
1
de la antena del automóvil*
1
från bilantenn*
1
da antena do automóvel*
1
απ την κεραία του αυτοκινήτου*
1
Source selector
(not supplied)
Selector de fuente
(no suministrado)
Väljare för ljudkälla
(medföljer inte)
Selector de fonte
(não fornecido)
Επιλογέας πηγής
(δεν παρέχεται)
XA-C30
Supplied to XA-C30
Suministrado con el XA-C30
Medföljer XA-C30
Fornecido para o XA-C30
Παρέχονται µε το XA-C30
Rotary commander RM-X4S (not supplied)
Mando rotativo RM-X4S (no suministrado)
Vridkontroll RM-X4S (medföljer inte)
Comando rotativo RM-X4S (não fornecido)
Περιστροφικ χειριστήριο RM-X4S (δεν παρέχεται)
*
2
*2
Fuse (10 A)
Fusible (10 A)
Säkring (10 A)
Fusivel (10 A)
Ασφάλεια (10 A)
to a car’s auxiliary power connector
a un conector de alimentación auxiliar del automóvil
till bilens yttre strömanslutning.
a um conector de alimentação auxiliar do automóvel
προς την υποδοχή βοηθητικής τροφοδοσίας του αυτοκινήτου
Insert with the cord upwards.
Insertar con el cable hacia arriba.
Sätt in med kabeln vänd uppåt.
Inserir com o fio virado para cima.
Εισάγετε µε το καλώδιο προς τα επάνω
WARNING
Auxiliary power connectors may vary depending on
the car. Be sure to check the power connection
diagram. Improper connections may damage your
car. If the supplied power connecting cord can not be
used with your car, consult your nearest Sony dealer.
ADVERTENCIA
Los conectores de alimentación auxiliar pueden
variar en función del automóvil. Asegúrese de
consultar el diagrama de conexión de alimentación.
Las conexiones incorrectas pueden dañar el
automóvil. Si no es posible utilizar con el automóvil
el cable de conexión de alimentación suministrado,
póngase en contacto con el proveedor Sony más
próximo.
VARNING
Typen av yttre strömanslutning varierar från bil till
bil. Kontrollera strömanslutningsschemat som
medföljer enheten så att du ansluter på rätt sätt.
Felaktig anslutning kan skada bilen. Kontakta
närmaste Sony-återförsäljare om den medföljande
strömkabeln inte passar till din bil.
ADVERTÊNCIA
Os conectores de corrente auxiliares podem variar de
carro para carro. Não se esqueça de verificar o
diagrama de ligação de corrente fornecido com o
aparelho. As ligações mal executadas podem
danificar o seu carro. Se não puder utilizar o cabo de
alimentação fornecido no seu carro, contacte o
agente Sony da sua zona.
ΠΡΟΕΙ∆ΟΠΟΙΗΣΗ
Οι βοηθητικές υποδοχές τροφοδοσίας µπορεί να
διαφέρουν ανάλογα µε το αυτοκίνητο. Ελέγξτε το
διάγραµµα σύνδεσης της τροφοδοσίας.
Λανθασµένες συνδέσεις µπορεί να προκαλέσουν
ζηµιά στο αυτοκίνητ σας. Αν το παρεχµενο
καλώδιο τροφοδοσίας δεν µπορεί να
χρησιµοποιηθεί στο αυτοκίνητ σας,
συµβουλευθείτε τον πλησιέστερο αντιπρσωπο της
Sony.
Supplied to the CD/MD changer
Suministrado con el cambiador de CD/MD
Medföljer CD/MD-växlaren
Fornecido para o permutador de CD/MD
Παρέχονται µε το CD/MD changer
Yellow
Amarillo
Gul
Amarelo
Κίτρινο
Blue
Azul
Blå
Azul
Μπλε
Orange/
White
Naranja/
blanco
Orange/vit
Cor de
laranja/
branco
Πορτοκαλί/
Λευκ
continuous power supply
suministro de alimentación continua
kontinuerlig strömförsörjning
alimentação de corrente contínua
συνεχής τροφοδοσία
power aerial control
control de antena motorizada
styrning av motorantenn
antena eléctrica
έλεγχος ηλεκτρικής κεραίας
switched illumination power
supply
fuente de alimentación de
iluminación conmutada
Switchad strömförsörjning till
belysning
fonte de alimentação comutada
para iluminação
διακοπτµενη τροφοδοσία
φωτεινής ένδειξης
1
2
3
4
Speaker, Rear, Right
Altavoz, parte posterior, derecho
Högtalare, bakre, höger
Altifalante, Parte de trás, Direito
Ηχείο, Πίσω, ∆εξί
Speaker, Rear, Right
Altavoz, parte posterior, derecho
Högtalare, bakre, höger
Altifalante, Parte de trás, Direito
Ηχείο, Πίσω, ∆εξί
Speaker, Front, Right
Altavoz, parte frontal, derecho
Högtalare, främre, höger
Altifalante, Parte da frente, Direito
Ηχείο, Εµπρς, ∆εξί
Speaker, Front, Right
Altavoz, parte frontal, derecho
Högtalare, främre, höger
Altifalante, Parte da frente, Direito
Ηχείο, Εµπρς, ∆εξί
5
6
7
8
Speaker, Front, Left
Altavoz, parte frontal, izquierdo
Högtalare, främre, vänster
Altifalante, Parte da frente, Esquerdo
Ηχείο, Εµπρς, Αριστερ
Speaker, Front, Left
Altavoz, parte frontal, izquierdo
Högtalare, främre, vänster
Altifalante, Parte da frente, Esquerdo
Ηχείο, Εµπρς, Αριστερ
Speaker, Rear, Left
Altavoz, parte posterior, izquierdo
Högtalare, bakre, vänster
Altifalante, Parte de trás, Esquerdo
Ηχείο, Πίσω, Αριστερ
Speaker, Rear, Left
Altavoz, parte posterior, izquierdo
Högtalare, bakre, vänster
Altifalante, Parte de trás, Esquerdo
Ηχείο, Πίσω, Αριστερ
Purple
Púrpura
Violett
Violeta
Μωβ
Negative polarity positions 2, 4, 6, and 8 have striped cords.
Las posiciones de polaridad negativa 2, 4, 6 y 8 tienen cables con raya.
De negativa polpositionerna 2, 4, 6 och 8 har randiga kablar.
As posições 2, 4, 6 e 8 (polaridade negativa) têm cabos às riscas.
Οι θ σεις αρνητικής πολικτητας 2, 4, 6, και 8 χουν καλώδια µε ρίγες.
Green
Verde
Grön
Verde
Πράσινο
White
Blanco
Vit
Branco
Λευκ
Grey
Gris
Grå
Cinzento
Γκρι
+
–
+
–
+
–
+
–
7
8
4
5
6
Red
Rojo
Röd
Vermelho
Κκκινο
Black
Negro
Svart
Preto
Μαύρο
switched power supply
suministro conmutado de alimentación
switchad strömförsörjning
alimentação de corrente comutada
διακοπτµενη τροφοδοσία
earth
toma de tierra
jord
Terra
γη
Positions 1, 2 and 3 do not have pins.
Las posiciones 1, 2 y 3 no disponen de
terminales.
Positionerna 1, 2 och 3 saknar stift.
As posições 1, 2 e 3 não têm terminais.
Οι θ σεις 1, 2 και 3 δεν χουν pin.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

10
XR-M510 SECTION 3
DISASSEMBLY
• See page 3 for Servicing Notes.
Note: Follow the disassembly procedure in the numerical order given.
MECHANISM DECK (MG-25E-136)
3 front panel assy
flexible board
Note: Don't pull out flexible board
from front panel assy.
1 screw (panel)
2 spacer (arm)
1 screw (panel)
2 spacer (arm)
5 two screws
(PTT2.6
× 6)
5 two screws
(PTT2.6
× 6)
4 flexible board
(CN401)
4 connector
(CN400)
6 mechanism deck
(MG-25E-136)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

11
XR-M510
1 cover (flexible)
2 flexible board
(CN402)
2 flexible cover
• Note for Installation of Flexible Board
1 Set the flexible board to
be at the position in the figure.
3 front panel assy
FRONT PANEL ASSY
MOTOR BLOCK ASSY, CAM (R) ASSY
4 screw
(PTT2.6
× 6)
4 screw
(PTT2.6
× 6)
3 motor block assy
2 two screws
(PTT2.6
× 6)
5 cam (R) assy
1 two connectors
(CN501, CN602)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

12
XR-M510
SUB PANEL (XR) SUB ASSY
MAIN BOARD
2 screw
(PTT2.6
× 6)
2 two screws
(PTT2.6
× 6)
2 screw
(PTT2.6
× 6)
1 flexible board
(CN601)
3 sub panel (XR) sub assy
2 two screws
(PTT2.6
× 8)
3 three ground point screws
(PTT2.6 × 6)
1 flexible board
(CN601)
2 screw
(PTT2.6 × 8)
4 main board
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

13
XR-M510
HEAT SINK
4 three screws
(PTT2.6
× 8)
4 two screws
(PTT2.6
× 8)
2 connector
(CN100)
3 cord (with connector) (ANT)
6 heat sink
1 Remove solder of
cord (with connector) (ANT).
5 two screws
(PTT2.6
× 12)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

14
XR-M510 SECTION 4
ASSEMBLY
Note: Follow the assembly procedure in the numerical order given.
4-1. FRONT PANEL MACHINERY
MOTOR BLOCK ASSY
CAM (R) ASSY
8 two screws
(PTT2.6
× 6)
9 screw (BTT)
1 cam (L)
6 washer (M)
5 gear (C)
6 washer (M)
6 washer (M)
4 gear (B)
3 gear (A)
7 bracket (motor) assy
Set bracket (motor) assy
to be at the position in the
figure.
switch
concave portion
hole
2 stop ring 1.5
Note: When installing cam (L), adjust the hole and concave portion.
1 cam (R)
concave portion
hole
2 stop ring 1.5
Note: When installing cam (R), adjust the hole and concave portion.
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

15
XR-M510
MOTOR BLOCK ASSY, CAM (R) ASSY
4 screw
(PTT2.6
× 6)
7 screw
(PTT2.6
× 6)
3 motor block assy
4 screw
(PTT2.6
× 6)
6 cam (R) assy
5 connector
(CN602)
5 connector
(CN501)
black wiring
yellow wiring
1 Supply the power to the motor.
Voltage : 9V
Yellow wiring : MOTOR –
Black wiring : MOTOR +
2 Motor stops at full open position.
full open position
–
+
7 screw
(PTT2.6
× 6)
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

16
XR-M510
4-2. MECHANISM DECK
HOUSING
ARM (SUCTION)
A part
C part
B part
D part
8 Hold the hanger by
bending the claw.
6 Fit projection on D part.
4 Fit claw on B part.
3 Put the housing
under
A part.
5 Fit projection on C part.
1 Install the catch to the hanger.
2 Install the hanger onto
two claws of the housing.
7 Holder the hanger by bending the claw.
hanger
housing
2 Move the arm (suction) in the arrow
direction and fit on projection.
1 Fit the arm (suction) on the shaft.
projection
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

17
XR-M510
shaft A
shaft B
shaft C
1
Fit the lever (LDG-A) on
shafts
A – C and install it.
shaft A
shaft B
2
Fit the lever (LDG-B) on
shafts
A and B and
install it.
3 type-E stop ring 2.0
LEVER (LDG-A) / (LDG-B)
GEAR (LDG-FT)
gear (LDG-D)
5 gear (LDG-FT)
6 polyethylene washer
2 tension spring (LD-2)
2 tension spring (LD-1)
gear (LDG-FB)
lever (LDG-A)
hole
hole
4 Align hole in the gear (LDG-D)
with hole the lever (LDG-A).
3 Move the lever (LDG-B)
in the arrow direction.
1
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

18
XR-M510
GUIDE (C)
MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901)
2 guide (C)
1 three claws
two precision screws
(P2
× 2)
Note: Mount the motor so that the
angle between of the
motor and the hole for the
screw becomes 30
° as
shown in this figure.
capstan/reel motor
(M901)
30˚
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

19
XR-M510
SECTION 5
MECHANICAL ADJUSTMENTS
Mode Tension Meter Meter Reading
Forward CQ-403A more than 90 g
(more than 3.18 oz)
Reverse CQ-403R more than 90 g
(more than 3.18 oz)
•TapeTension Measurement
1. Clean the following parts with a denatured-alcohol-moistened
swab:
playback head pinch roller
rubber belt capstan
idler
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. The adjustments should be performed with the power supply
voltage (14.4V) unless otherwise noted.
•Torque Measurement
Mode Torque Meter Meter Reading
2.95 – 6.73 mN•m
Forward CQ-102C 30 – 65 g•cm
(0.42 – 0.90 oz•inch)
Forward 0.05 – 0.44mN•m
CQ-102C 0.5 – 4.5 g•cm
Back Tension (0.01 – 0.06 oz•inch)
2.95 – 6.73 mN•m
Reverse CQ-102RC (25 – 55 g•cm)
(0.42 – 0.90 oz•inch)
Reverse 0.05 – 0.44mN•m
CQ-102RC 0.5 – 4.5 g•cm
Back Tension (0.01 – 0.06 oz•inch)
5.89 – 19.61 mN•m
FF, REW CQ-201B 60 – 200 g•cm)
(0.83 – 2.78 oz•inch)
SECTION 6
ELECTRICAL ADJUSTMENTS
TEST MODE
<Set the Test Mode>
1. Turn ON the regulated power supply. (All LEDs on the set
lights up, and the clock is displayed.)
Note: Press the [OFF] button, if the clock is not displayed.
2. Push the preset [4] button.
3. Push the preset [5] button.
4. Press the preset [1] button for more than two seconds.
5. Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the [OFF] button.
Tape Speed Adjustment
Setting:
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the frequency counter becomes in 3,015 Hz.
Specified Value: 2,955 to 3,075 Hz
Adjustment Location: See page 20.
0 dB=0.775 V
TAPE DECK SECTION
frequency counter
test tape
WS-48A
(3 kHz, 0 dB)
set
AUDIO OUT REAR jack (CN300)
–
+
10 k
Ω
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com

20
XR-M510
Dolby Level Adjustment
Setting:
[SOURCE] button : ON
Preset [MENU] (PLAY MODE) and
[DISC ] buttons : NR off
[SOUND] (BAS) button : Center
[SOUND] (TRE) button : Center
[SOUND] (BAL) button : Center
[SOUND] (FAD) button : Center
[+] (VOL) button : Maximum
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust RV400 (L-CH) and RV401 (R-CH) so that the level
meter reading is –6±0.5 dB (0.37 to 0.41 V).
Tuner section adjustments are done automatically in this set.
set +
–
test tape
P-4-D400
(400Hz, 0 dB) level mete
r
MAIN board
TP (D LBY-L)/
TP (D LBY-R)
      
TUNER SECTION
–
– SET UPPER VIEW –
– SET BOTTOM VIEW –
TUX100
Tape Speed
Adjustment
RV401
Dolby Level
Adjutment (R-ch
)
RV400
Dolby Level
Adjutment (L-ch)
TP (DOLBY-R) Dolby Level
Adjustment
TP (DOLBY-L)
Adjustment Location:
w w w . x i a o y u 1 6 3 . c o m
Q Q
3
7
6 3
1 5 1 5
0 9 9
2
8 9
4 2
9 8
T E L 1 3 9 4 2 2 9 6 5 1 3 9 9 2 8 9 4 2 9 8 0 5 1 5 1 3 6 7 3
Q Q
TEL [phone] QQ 376315150 892498299 TEL [phone] QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com