
Information in this document is subject
to change without notice.
Sony, VAIO and CLIE are trade marks
or registered of Sony. Microsoft, Windows,
Windows Media, Outlook, Bookshelf and
other Microsoft products are trademarks
or registered trademarks of Microsoft
Corporation in the United States and other
countries. The word Bluetooth and the
Bluetooth logo are trademarks of Bluetooth
SIG, Inc. AMD,AMD logo, AMD Duron
and combinations there of, 3Dnow!, are
trademarks of Advanced micro Devices,
Inc. Intel Inside logo, Pentium and Celeron
are trademarks or registered trademarks if
Intel Corporation. Transmeta, the Transmeta
logo, Crusoe processor, the Crusoe logo and
combination there of are trademarks of
Transmeta Corporation in the USA and other
countries. Graffiti, Hotsync, PalmModem,
and palm OS are registered trademarks, and
the Hotsync logo and Palm are trademarks of
Plam,Inc.or its subsidiaries. (M)and Motrola
are trademarks of Motrora, Inc. Other Motrola
products and services with (R) mark like
Dragomball are the trademarks of Motrola, Inc.
All other names of systems, products and services
in this manual are trademarks or registered
trademarks of their respective owners.In this
manual, the (TM)or(R)mark are not specified.
Caution Markings foe Lithium/Ion Battery-
The following or similar texts shall be provided on
battery pack of equipment or in both the operating
and the service instructions.
CAUTION: Danger of explosion if battery is
incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.
Discard used batteries according to the
Manufacturer’
CAUTION: The battery pack used in this device may
present a fire or chemical burn hazard if mistreated.
Do not disassemble, heat above 100к(212л) or
incinerate. Dispose of used battery promptly. Keep
Away from children..
CAUTION: Changing the back up battery.
ΗOvercharging, short circuiting, reverse charging,
multilati on or incineration of the cells must be
avoided to prevent one or more of the following
occurrences; release of toxic materials, release of
hydrogen and/or oxygen gas, rise in surface
temperature.
ΗIf a cell has leaked or vented, it should be replaced
immediately while avoiding to touch it without any
protection..
*
*1.Obey precautionary markings and instructions
* Labels and stamps on the cabinet,
*chassis, and components are as
*requiring special precautions. Be
*sure to observe these precautions,
*as well as all precautions listed in
*the operating manual and other
*associated documents..
*2.Use designated parts only
*The set’s components possess important safety
*characteristics, such as noncombustibility and the
*ability to tolerate large voltages.
* Be sure that replacement parts possess the same
*safety characteristics as the originals. Also
*remember that the mark, *which appears in circuit
*diagrams and parts lists, denotes components that
*have particularly important safety functions be extra
*sure to use only the designated components.
*3. Always follow the original design when
*mounting parts and routing wires
*
*The original layout includes various
*safety features, such as inclusion of
*insulating materials (tubes and tape) and
*the mounting of parts above the printer
*board. In addition, internal wiring has
*been routed and clamped so as to keep it
away from hot or high -voltage parts. When mountin
parts or routing wires, therefore, be sure to duplica
the original layout.
4. Inspect after completing service
After servicing, inspect to make Sure that all screws,
components, And wiring have been returned to their
original condition. Also check the area around the
repair location to ensure that repair work has caused
no damage, and confirm safety.
5.When replacing chip components
ever reuse components. Also remember that th
negative side of tantalum capacitors is easil
Damaged by heat.,
6.When handing flexible print boards
ΗT he temperature of the soldering-Iron tip shou
be about 270к.
ΗDo not apply the tip more than three times t
the same pattern.
ΗHandle patterns with care; never apply forc
Caution: Remember that hard
disk drives are easily damaged
by vibration. Always handle
with care.
Service and Inspection Precautions
2Sony Confidential