Sony M-100MC - Microcassette Dictaphone User manual

M-100MC
SERVICE MANUAL
MICROCASSETTE™-CORDER
SPECIFICATIONS
US Model
Canadian Model
AEP Model
E Model
Tourist Model
Tape
y(normal position type)
Recording system
2-track 1-channel monaural
Speaker
Approx. 2.8cm (1 1/8in.) dia.
Tape speed
2.4cm/s (15/16 ips), 1.2cm/s (15/32 ips)
Frequency range
High : 400 – 3,000Hz
Normal, Low : 400 – 4,000Hz
Output
Earphone jack (minijack) for 8 – 300ohms earphone
Power output (at 10% harmonic distortion)
220mW
Battery life (Approx. hours) (EIAJ*)
Batteries Recording
Sony alkaline LR6 (SG) 16.0
Sony R6P (SR) 5.5
*Measured value by the standard of EIAJ (Electronic Industries
Association of Japan) (Using a Sony Microcassette MC-60)
Power requirements
3V DC
Two R6 (size AA) batteries
Dimensions (w/h/d)
Approx. 126.0 x 68.0 x 40.8 mm (5 x 2 3/4x 15/8in.) incl.
projecting parts and controls
Mass
Approx. 180g (6.4 oz) incl. batteries
Supplied Accessories
Hand strap (attached to the unit) (1)
Microcassette tape (1) (EXCEPT US, Canadian, AEP model)
Wind screen (1) (US model)
R6 (size AA) batteries (2) (Tourist model)
Earphone (1) (Tourist model)
Design and specifications are subject to change without notice.
Model Name Using Similar Mechanism NEW
Tape Transport Mechanism Type MZ-100MC-14
Sony Corporation
Personal Audio Group
Published by Sony Engineering Corporation
9-923-382-12
2005E02-1
© 2005.05
Ver. 1.1 2005.05

– 2 –
Specifications ........................................................................... 1
1. GENERAL
Location and Function of Controls .................................... 2
2. DISASSEMBLY
2-1. Rear Cabinet Assy Removal ....................................... 3
2-2. Front Cabinet Assy, Main Unit Removal.................... 3
2-3. Mechanism Deck Removal......................................... 4
2-4. MIC-SP Block Assy, Main Board Removal ............... 4
2-5. LED Board, Cassette Lid Assy Removal ................... 5
2-6. Eject Arm Installation ................................................. 5
3. ADJUSTMENTS
3-1. Mechanical Adjustments ............................................ 6
3-2. Electrical Adjustments ................................................ 6
4. DIAGRAMS
4-1. Block Diagram............................................................ 8
4-2. Printed Wiring Boards .............................................. 10
4-3. Schematic Diagram................................................... 13
5. EXPLODED VIEWS
5-1. Front Section ............................................................ 17
5-2. Mechanism Deck Section ......................................... 18
6. ELECTRICAL PARTS LIST.................................... 19
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when
soldering or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
TABLE OF CONTENTS
SECTION 1
GENERAL
LOCATION AND FUNCTION OF CONTROLS
MICROCASSETTE-CORDER M-100MC
MODEL IDENTIFICATION
Indication of country of origin :
US, Canadian, AEP, E, Tourist model
No indication of country of origin : 1E model
1PPAUSE switch
2CUE MARKER button
3VOL control
4REC indicator
5Microphone
6Speaker
7SENSITIVITY selector
8BATT indicators and iindicator
9r(recording) button
!º ((playback) button
!¡ )(fast-forward)/(cue) • 0(rewind)/(review) switch
!™ VOR switch
!£ FIRST PB switch
!¢ Handstrap
!∞TAPE SPEED switch
!§ EAR jack
!¶ DC IN 3V jack
!• p,(stop/eject) button
!ª TAPE COUNTER

– 3 –
SECTION 2
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
2-1. REAR CABINET ASSY REMOVAL
2-2. FRONT CABINET ASSY, MAIN UNIT REMOVAL
rThe equipment can be removed using the following procedure.
4 Screws (B 1.7x13.5)
5 Screw
(B 1.7x7)
Hand strap
Front cabinet assy
FR knob
Pause knob
Foot (cabinet)
Button (stand)
3
6
2
1
Rear cabinet assy
Stand assy
Lid, battery case

Front cabinet assy
LED flexible board
main board (W101)
Main unit
1
2

Front cabinet assy
Rear cabinet assy
Cassette lid assy
Set MIC-SP block assy, Main board
Mechanism deck
Main unit
LED board

– 4 –
2-4. MIC-SP BLOCK ASSY, MAIN BOARD REMOVAL
2-3. MECHANISM DECK REMOVAL
2 Screw (M1.4)
1 Remove solder
1 Remove solder
MIC-SP block ass
y
Main board
3
Battery terminal
Yellow
Red Black
Brown
Yellow
Blue
2 Screws
1 Remove solder
1 Remove solder
3
4
Mechanism dec
k
MIC-SP block assy
Blue
Red
Head flexble board
Main board Belt

– 5 –
2-5. LED BOARD, CASSETTE LID ASSY REMOVAL
2-6. EJECT ARM INSTALLATION
1 Tapping (1.7x3)
LED board
3
7
5
4
2
6
Cassette lid assy
Front cabinet assy
Eject arm
4
2
3
1
5
Front cabinet assy
Spring (toggle),
torshion
Eject arm
Eject arm

– 6 –
SECTION 3
ADJUSTMENTS
3-1. MECHANICAL ADJUSTMENTS
PRECAUTION
1. Before adjusting, clean the following parts with a piece of cot-
ton moistened with alcohol.
record/playback/erase head pinch roller
rubber belt capstan
2. Demagnetize the record/playback/erase head using a head de-
magnetizer.
3. Do not use a magnetized screwdriver for adjustments.
4. After adjusting, apply screw-locking compound to the adjusted
parts.
5. Unless specified otherwise, use a specified voltage (3V DC) to
perform the adjustments.
Torque Measurement
Tape Speed switch : 2.4cm
Mode Torque Meter Meter Reading
Forward CQ-103M 5 – 13 g • cm
(0.07 to 0.180 oz• inch)
Fast Forward CQ-201M 5 – 13 g • cm
(0.07 to 0.180 oz• inch)
Rewind CQ-201M more than 20 g • cm
(more than 0.28 oz• inch)
TapeTension Measurement
Tape Speed switch : 2.4cm/s
Mode Torque Meter Meter Reading
FWD CQ-403M more than 30 g
(more than 1.06 oz)
3-2. ELECTRICAL ADJUSTMENTS
Standard Output Level
Output terminal EAR
Load impedance 10kΩ
Output level 78mV (– 20dB)
TestTape
Type Signal Used for Tape speed
(cm/s)
S-2-A030A 3kHz, –20dB Azimuth Adjustment 2.4
WS-24 3kHz, –10dB Tape Speed Adjustment 2.4
WS-12 1.2
0dB=0.775V
Record/Playback/Erase Head Azimuth Adjustment
Switch position
VOL control : Mechanical center
TAPE SPEED switch : 2.4cm
VOR switch : OFF
Procedure :
– FWD/REV playback –
• Rotate the screw to adjust level meter reading to the maximum.
Note : Adjust to the maximum peak though ther may be two or
three peaks
Adjustment Location :
set
test tape
S-2-A030A
(3kHz, –20dB) level mete
r
EAR jack
10k
Ω
First remove the cover
(azimuth)
head azimuth
adjustment screw

– 7 – – 9 –– 8 –
Tape Speed Adjustment
Switch position
VOL contorl : Mechanical center
VOR switch : OFF
Procedure:
After adjusting the 1.2cm/s speed, adjust the 2.4cm/s speed.
– Playback –
Adjustment Value :
Adjustment Speed Speed checker Frequency counter
Part
RV601 1.2cm/s – 3% ~ + 3% 1,455 – 1,545Hz
RV602 2.4cm/s – 3% ~ + 3% 2,910 – 3,090Hz
Frequency difference between the beginning and the end of the
tape should be within 0.5%.
2.4cm/s (15Hz)
1.2cm/s (7.5Hz)
AdjustmentLocation :
– Back view –
set
Test tape
WS-24
(3kHz, –10dB)
speed checker
or
frequency counter
EAR jack
10k
Ω
RV602
2.4cm/s RV601 1.2cm/s
speed adjustable resistors
lid, battery case
• Signal path.
E: PB
a: REC
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM
M-100MC

– 16 – – 18 –– 17 –
rIC BLOCK DIAGRAM
IC101 LA4168ML-TE-L
21
222324
2526272829
30
235
4678910
111 12 13 14 15
16
17
1819
20
300k
EQ MIC
2.2k
30k
2k
PAUSE
POWER
MIC
VCC
Vref R/P
R, F
GVN
VOX
SPEED
ALC
VOX
20k
REC
12
PRE GND EQ IN MIC IN Vref OUT MIC VCC R. F OUT LED DRIVE R/P SW PAUSE P/R MUTE GVN CONT GVN Vref Vs GVN GND GVN OUT
PRE NF
PRE OUT
REC IN
REC OUT
ALC CONT
VOX CONT
VOX DELAY
NC NC NC
PWR IN
PWR OUT1
PWR GND
PWR OUT2
Vcc
SECTION 5
EXPLODED VIEWS
NOTE :
•-XX, -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “ * ”are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
•The mechanical parts with no reference
number in the exploded views are not
supplied.
•Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
5-1. FRONT SECTION
•Abbreviation
E:Indication of country of origin
1E : No indication of country of origin
13-025-026-01 BUTTON (STAND)
2X-3375-565-1 STAND ASSY
33-318-382-31 SCREW (1.7X3), TAPPING
*43-025-036-01 BRACKET (SPK)
*53-025-030-01 BRACKET (M-SP)
63-704-197-91 SCREW (IB LOCK)
73-025-031-01 HOLDER (M-SP)
83-025-024-01 BRACKET (PANEL MIC)
93-025-043-01 SHEET (WS)
10 3-025-023-01 PANEL (MIC)
11 A-3021-101-A MAIN BOARD, COMPLETE
12 3-025-037-01 TERMINAL, BATTERY
13 3-025-038-01 SPRING, BATTERY COIL
14 X-3375-600-1 CABINET (REAR) ASSY (EXCEPT 1E)
14 X-3375-956-1 CABINET (REAR) ASSY (1E)
15 3-334-565-21 SCREW (B1.7X13.5), TAPPING
16 3-318-203-82 SCREW (B1.7X7), TAPPING
17 3-025-019-01 LID, BATTERY CASE
18 3-025-017-01 KNOB (PAUSE)
19 3-025-018-01 KNOB (FR)
20 3-010-491-01 BUTTON (REC)
21 3-010-492-01 BUTTON (PLAY)
22 3-010-493-01 BUTTON (STOP)
23 3-669-481-07 PIN (DIA.1X10), PARALLEL
24 3-328-319-31 STRAP, HAND
26 3-025-013-11 BUTTON (CUE)
27 3-027-880-01 SPRING (TOGGLE), TORSION
28 3-010-499-01 ARM (EJECT)
29 X-3375-599-1 CABINET (FRONT) ASSY
30 3-025-029-01 FOOT (CABINET)
31 X-3375-566-1 LID ASSY, CASSETTE
32 3-025-039-01 COVER (AZIMUTH)
33 3-025-033-01 KNOB (SENSITIVITY SELECTION)
*34 3-025-040-01 BRACKET (SENSITIVITY)
35 3-669-481-05 PIN (DIA.1X15), PARALLEL
38 3-342-156-61 SCREW
39 3-025-032-01 CUSHION, MICROPHONE
40 A-3021-100-A LED BOARD, COMPLETE
41 3-345-648-01 SCREW (M1.4), TOOTHED LOCK
42 3-025-041-01 SHEET (BLIND)
43 3-025-042-01 PAPER, SHIELD
44 3-026-293-01 CUSHION (BATTERY)
45 1-669-666-11 LED FLEXIBLE BOARD
MIC901 1-542-348-11 MICROPHONE, ELECTRET CONDENSER
MIC902 1-542-298-11 MICROPHONE, ELECTRET CONDENSER
SP901 1-505-918-11 SPEAKER (2.8cm)
SP901
MIC902
not supplied
MIC901
1
2
3
3
3
4
7
6
6
39
8
9
10
11 12
13
14
15
15 16
17
18
19
20
21
22 23
24
26
27
28
29 30
31
32
33
34
35
3
3
5
38
41
42
43
44
40
45
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 X-3371-272-1 FLYWHEEL (M) ASSY
52 3-914-904-01 SPRING (PFR), TORSION
53 3-704-243-11 SCREW (P1.7X2.0)
*54 3-023-941-01 PLATE (FR), LOCK
*55 3-914-919-01 SLIDER (FR)
56 3-914-903-01 SPRING (FR), TORSION
57 3-914-915-01 ARM (S.OFF)
58 3-914-906-01 SPRING (S.OFF), TORSION
59 3-377-420-11 BELT
60 X-3368-585-1 PINCH LEVER ASSY
61 X-3375-404-1 LEVER (STOP) ASSY
62 3-343-948-01 BELT
63 3-023-935-01 BELT
64 X-3375-403-1 BRACKET ASSY, COUNTER
65 1-251-705-11 COUNTER, TAPE
66 X-3368-582-1 REEL ASSY, T
67 3-914-914-12 GUIDE, TAPE
*68 X-3369-557-1 CHASSIS COMPLETE ASSY (D)
*69 3-914-913-01 LEVER (PLAY)
70 3-914-902-01 SPRING (P), TORSION
71 3-704-245-42 SCREW (1.4)
72 3-366-746-51 SCREW (M1.4X6.5)
73 3-378-792-01 SPRING, COMPRESSION
74 X-3368-584-1 ARM (MIDWAY GEAR) ASSY
75 3-331-007-21 WASHER
*76 3-914-923-11 COVER, MD
77 3-331-047-01 SCREW (M1.4X1.4),SPECIAL HEAD
78 3-914-908-01 SPRING (REC LOCK), TENSION
79 3-914-907-01 SPRING (MIDWAY GEAR), TORSION
80 X-3368-587-1 REEL ASSY, S
*81 X-3368-583-1 LEVER (REC) ASSY
82 3-914-916-01 ARM (CLAW DETECTION)
HCB901 1-500-527-11 HEAD,MAGNETIC(RECODE/PLAYBACK/ERASE)
M901 1-698-533-21 MOTOR, DC
5-2. MECHANISM DECK SECTION
(MZ-100MC-14)
HCB901
M901
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65 66 67
68
69
70
71 72
73
74
75
76
77
78
79
80
81
82
Ver. 1.1

– 19 –
NOTE :
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms
METAL : Metal-film resistor
METAL OXIDE :Metal oxide-film resistor
F : nonflammable
• Items marked “ * ”are not stocked since
they are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example :
uA.... : µA.... , uPA.... : µPA....
uPB.... : µPB.... , uPC.... : µPC....
uPD.... : µPD....
• CAPACITORS
uF : µF
• COILS
uH : µH
When indicating parts by reference num-
ber, please include the board.
SECTION 6
ELECTRICAL PARTS LIST
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-3021-100-A LED BOARD, COMPLETE
********************
1-669-666-11 LED FLEXIBLE BOARD
< CAPACITOR >
C501 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C502 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
< DIODE >
D401 8-719-985-81 LED HLMP-Q150 (REC)
D501 8-719-062-42 LED BR1111R-TR (BATT • •)
D502 8-719-062-42 LED BR1111R-TR (BATT • )
D503 8-719-062-43 LED AY1111R-TR (i)
< IC >
IC501 8-759-399-49 IC MM1251BFBE
< COIL >
L501 1-412-032-11 INDUCTOR CHIP 100uH
< TRANSISTOR >
Q501 8-729-402-93 TRANSISTOR UN5214-TX
< RESISTOR >
R501 1-216-106-00 METAL CHIP 240K 5% 1/10W
R502 1-216-101-00 METAL CHIP 150K 5% 1/10W
R503 1-216-083-00 METAL CHIP 27K 5% 1/10W
R504 1-216-689-11 METAL CHIP 39K 0.5% 1/10W
R505 1-216-033-00 METAL CHIP 220 5% 1/10W
R506 1-216-037-00 METAL CHIP 330 5% 1/10W
R507 1-216-037-00 METAL CHIP 330 5% 1/10W
R508 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
R509 1-216-045-00 METAL CHIP 680 5% 1/10W
< SWITCH >
S102 1-570-386-11 SWITCH, SLIDE (SENSITIVITY)
************************************************************
A-3021-101-A MAIN BOARD, COMPLETE
*********************
3-025-037-01 TERMINAL, BATTERY
3-025-038-01 SPRING, BATTERY COIL
< CAPACITOR >
C101 1-164-346-11 CERAMIC CHIP 1uF 16V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V
C104 1-164-346-11 CERAMIC CHIP 1uF 16V
C105 1-164-346-11 CERAMIC CHIP 1uF 16V
C106 1-126-607-11 ELECT CHIP 47uF 20% 4V
C107 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C108 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C109 1-164-346-11 CERAMIC CHIP 1uF 16V
C110 1-163-037-11 CERAMIC CHIP 0.022uF 50V
C111 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C112 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C113 1-164-346-11 CERAMIC CHIP 1uF 16V
C114 1-164-346-11 CERAMIC CHIP 1uF 16V
C115 1-164-346-11 CERAMIC CHIP 1uF 16V
C116 1-124-779-00 ELECT CHIP 10uF 20% 16V
C117 1-128-024-11 ELECT CHIP 4.7uF 20% 10V
C118 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
C119 1-128-015-11 ELECT CHIP 22uF 20% 4V
C120 1-163-037-11 CERAMIC CHIP 0.022uF 10% 50V
C121 1-164-346-11 CERAMIC CHIP 1uF 16V
C122 1-164-346-11 CERAMIC CHIP 1uF 16V
C123 1-164-346-11 CERAMIC CHIP 1uF 16V
C124 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C125 1-126-246-11 ELECT CHIP 220uF 20% 4V
C126 1-126-209-11 ELECT CHIP 100uF 20% 4V
C127 1-126-246-11 ELECT CHIP 220uF 20% 4V
C128 1-124-779-00 ELECT CHIP 10uF 20% 16V
C129 1-164-699-11 CERAMIC CHIP 0.0033uF 5% 50V
C130 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
C131 1-163-010-11 CERAMIC CHIP 0.0012uF 10% 50V
C132 1-126-607-11 ELECT CHIP 47uF 20% 4V
C133 1-164-346-11 CERAMIC CHIP 1uF 16V
C134 1-164-346-11 CERAMIC CHIP 1uF 16V
C135 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C136 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C137 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C138 1-164-346-11 CERAMIC CHIP 1uF 16V
C140 1-164-346-11 CERAMIC CHIP 1uF 16V
C141 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C142 1-163-038-91 CERAMIC CHIP 0.1uF 25V
• Abbreviation
E :Indication of country of origin
1E :No indication of country of origin
LED MAIN

– 20 –
C143 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C144 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C145 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C146 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C148 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C149 1-164-346-11 CERAMIC CHIP 1uF 16V
C150 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C153 1-163-809-11 CERAMIC CHIP 0.047uF 10% 25V
C154 1-164-232-11 CERAMIC CHIP 0.01uF 50V
C155 1-164-346-11 CERAMIC CHIP 1uF 16V
C156 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C158 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C160 1-164-346-11 CERAMIC CHIP 1uF 16V
C301 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C302 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V
C303 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C304 1-135-151-21 TANTALUM CHIP 4.7uF 20% 4V
C401 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C402 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C403 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C601 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V
< DIODE >
D101 8-719-820-05 DIODE 1SS181
D102 8-719-420-51 DIODE MA729
D103 8-719-404-49 DIODE MA111
D104 8-719-404-49 DIODE MA111
D105 8-719-404-49 DIODE MA111
< IC >
IC101 8-759-492-49 IC LA4168ML-TE-L
< JACK >
J101 1-750-061-11 JACK,DC(POLARITY UNIFIED TYPE)
(DC IN 3V)
J102 1-784-848-21 JACK (EAR)
< JUMPER RESISTOR >
JC101 1-216-295-00 METAL CHIP 0 5% 1/10W
JC102 1-216-295-00 METAL CHIP 0 5% 1/10W
JC103 1-216-296-00 METAL CHIP 0 5% 1/8W
JC104 1-216-295-00 METAL CHIP 0 5% 1/10W
JC105 1-216-295-00 METAL CHIP 0 5% 1/10W
JC106 1-216-295-00 METAL CHIP 0 5% 1/10W
JC107 1-216-296-00 METAL CHIP 0 5% 1/8W
JC108 1-216-295-00 METAL CHIP 0 5% 1/10W
JC109 1-216-295-00 METAL CHIP 0 5% 1/10W
JC120 1-216-295-00 METAL CHIP 0 5% 1/10W
JC121 1-216-295-00 METAL CHIP 0 5% 1/10W
< TRANSISTOR >
Q101 8-729-429-74 TRANSISTOR 2SC3929
Q102 8-729-429-74 TRANSISTOR 2SC3929
Q103 8-729-422-39 TRANSISTOR XN4404
Q104 8-729-800-37 TRANSISTOR 2SD1048-X7
Q105 8-729-230-63 TRANSISTOR 2SC4116-YG
Q106 8-729-402-93 TRANSISTOR UN5214-TX
Q107 8-729-230-63 TRANSISTOR 2SC4116-YG
Q108 8-729-420-50 TRANSISTOR UN5215
Q109 8-729-420-50 TRANSISTOR UN5215
Q110 8-729-402-96 TRANSISTOR UN5114
Q111 8-729-028-30 TRANSISTOR UN511F
Q112 8-729-425-18 TRANSISTOR XN4504
Q113 8-729-402-93 TRANSISTOR UN5214-TX
Q115 8-729-230-63 TRANSISTOR 2SC4116-YG
Q116 8-729-420-50 TRANSISTOR UN5215
Q117 8-729-420-24 TRANSISTOR 2SB1218A-QRS
Q118 8-729-402-93 TRANSISTOR UN5214-TX
Q119 8-729-402-96 TRANSISTOR UN5114
Q120 8-729-402-93 TRANSISTOR UN5214-TX
Q122 8-729-429-74 TRANSISTOR 2SC3929
Q123 8-729-402-93 TRANSISTOR UN5214-TX
Q125 8-729-429-71 TRANSISTOR XN4314
Q130 8-729-403-17 TRANSISTOR XN1215
Q301 8-729-402-81 TRANSISTOR XN4501
Q302 8-729-429-71 TRANSISTOR XN4314
Q303 8-729-230-63 TRANSISTOR 2SC4116-YG
Q401 8-729-402-84 TRANSISTOR XN4601
Q402 8-729-420-50 TRANSISTOR UN5215
Q403 8-729-402-96 TRANSISTOR UN5114
Q601 8-729-402-93 TRANSISTOR UN5214-TX
Q602 8-729-420-53 TRANSISTOR UN5115
< RESISTOR >
R101 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R102 1-216-097-91 RES,CHIP 100K 5% 1/10W
R103 1-216-081-00 METAL CHIP 22K 5% 1/10W
R104 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R105 1-216-097-91 RES,CHIP 100K 5% 1/10W
R106 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R108 1-216-047-91 RES,CHIP 820 5% 1/10W
R109 1-216-097-91 RES,CHIP 100K 5% 1/10W
R110 1-216-097-91 RES,CHIP 100K 5% 1/10W
R111 1-216-089-91 RES,CHIP 47K 5% 1/10W
R112 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R113 1-216-081-00 METAL CHIP 22K 5% 1/10W
R114 1-216-176-11 RES,CHIP 120 5% 1/8W
R115 1-216-039-00 METAL CHIP 390 5% 1/10W
R116 1-216-077-00 METAL CHIP 15K 5% 1/10W
R117 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R118 1-216-009-00 METAL CHIP 22 5% 1/10W
R119 1-216-049-91 RES,CHIP 1K 5% 1/10W
R120 1-216-113-00 METAL CHIP 470K 5% 1/10W
R121 1-216-097-91 RES,CHIP 100K 5% 1/10W
R122 1-216-204-00 RES,CHIP 1.8K 5% 1/8W
R123 1-216-043-91 RES,CHIP 560 5% 1/10W
R124 1-216-150-91 RES,CHIP 10 5% 1/8W
R126 1-216-023-00 METAL CHIP 82 5% 1/10W
R127 1-216-011-00 METAL CHIP 27 5% 1/10W
R128 1-216-077-00 METAL CHIP 15K 5% 1/10W
R129 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R130 1-216-065-91 RES,CHIP 4.7K 5% 1/10W
R131 1-216-084-00 METAL CHIP 30K 5% 1/10W
R132 1-216-081-00 METAL CHIP 22K 5% 1/10W
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

– 21 –
R133 1-216-085-00 METAL CHIP 33K 5% 1/10W
R134 1-216-085-00 METAL CHIP 33K 5% 1/10W
R135 1-216-037-00 METAL CHIP 330 5% 1/10W
R136 1-216-033-00 METAL CHIP 220 5% 1/10W
R137 1-216-089-91 RES,CHIP 47K 5% 1/10W
R138 1-216-073-00 METAL CHIP 10K 5% 1/10W
R140 1-216-093-00 METAL CHIP 68K 5% 1/10W
R141 1-216-105-91 RES,CHIP 220K 5% 1/10W
R142 1-216-081-00 METAL CHIP 22K 5% 1/10W
R145 1-216-081-00 METAL CHIP 22K 5% 1/10W
R146 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R147 1-216-097-91 RES,CHIP 100K 5% 1/10W
R148 1-216-041-00 METAL CHIP 470 5% 1/10W
R149 1-216-037-00 METAL CHIP 330 5% 1/10W
R150 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R301 1-216-095-00 METAL CHIP 82K 5% 1/10W
R302 1-216-097-91 RES,CHIP 100K 5% 1/10W
R303 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R304 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R305 1-216-097-91 RES,CHIP 100K 5% 1/10W
R306 1-216-025-91 RES,CHIP 100 5% 1/10W
R307 1-216-113-00 METAL CHIP 470K 5% 1/10W
R308 1-216-129-00 METAL CHIP 2.2M 5% 1/10W
R401 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R402 1-216-031-00 METAL CHIP 180 5% 1/10W
R403 1-216-119-00 METAL CHIP 820K 5% 1/10W
R404 1-216-073-00 METAL CHIP 10K 5% 1/10W
R601 1-216-085-00 METAL CHIP 33K 5% 1/10W
R602 1-216-214-00 RES,CHIP 4.7K 5% 1/8W
R603 1-216-089-91 RES,CHIP 47K 5% 1/10W
R604 1-216-066-00 METAL CHIP 5.1K 5% 1/10W
R605 1-216-047-91 RES,CHIP 820 5% 1/10W
< VARIABLE RESISTOR >
RV101 1-225-597-11 RES, VAR, CARBON 10K (VOL)
RV601 1-238-663-11 RES, ADJ, CARBON 4.7K
(TAPE SPEED 1.2cm/s)
RV602 1-223-997-21 RES, CARBON ADJ VAR 47K
(TAPE SPEED 2.4cm/s)
< SWITCH >
S101 1-572-688-11 SWITCH, PUSH (1 KEY) (POWER)
S103 1-572-922-11 SWITCH, SLIDE (PAUSE c)
S104 1-692-999-11 SWITCH, SLIDE (PB/REC)
S105 1-572-922-11 SWITCH, SLIDE (VOR)
S301 1-692-088-11 SWITCH, TACTILE (PUSH CUE MARKER)
S601 1-572-922-11 SWITCH, SLIDE (FAST PB)
S602 1-572-688-11 SWITCH, PUSH (1 KEY) ())
S603 1-571-277-51 SWITCH, SLIDE (TAPE SPEED)
< TRANSFORMER >
T101 1-433-286-11 TRANSFORMER, BIAS OSCILLATION
< THERMISTOR >
TH601 1-801-744-11 THERMISTOR, POSITIVE
TH602 1-810-552-11 THERMISTOR, POSITIVE
< CONNECTOR >
W101 1-750-349-21 CONNECTOR, FFC/FPC (ZIF) 9P
************************************************************
MISCELLANEOUS
*************
45 1-669-666-11 LED FLEXIBLE BOARD
65 1-251-705-11 COUNTER, TAPE
HCB901 1-500-527-11 HEAD,MAGNETIC(RECODE/PLAYBACK/ERASE)
M901 1-698-533-21 MOTOR, DC
MIC901 1-542-348-11 MICROPHONE, ELECTRET CONDENSER
MIC902 1-542-298-11 MICROPHONE, ELECTRET CONDENSER
SP901 1-505-918-11 SPEAKER (2.8cm)
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
*2-283-326-01 LABEL, CAUTION (Tourist)
3-025-039-01 COVER (AZIMUTH)
3-862-343-11 MANUAL, INSTRUCTION (ENGLISH)
(US,Canadian,AEP)
3-862-343-21 MANUAL, INSTRUCTION (FRENCH) (Canadian)
3-862-343-31 MANUAL, INSTRUCTION(FRENCH,
PORTUGUESE,ITALIAN, DUTCH)
(AEP,E,Tourist)
3-862-343-41 MANUAL, INSTRUCTION (GERMAN, SPANISH,
SWEDISH, FINNISH) (AEP)
3-862-343-51 MANUAL, INSTRUCTION (ENGLISH, SPANISH,
CHINESE, KOREAN) (E,Tourist)
3-862-343-61 MANUAL, INSTRUCTION (JAPANESE) (Tourist)
3-862-343-71 MANUAL, INSTRUCTION (ENGLISH, SPANISH,
CHINESE, KOREAN) (1E)
8-952-251-90 HEADPHONE MDR-E122 SET
X-3375-567-1 SCREEN ASSY, WINDOW (US, Canadian,
Tourist)
MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

M-100MC
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision
1.0 1998.04 New
1.1 2005.05 Change of the supply classification of the stand (strap). (SPM-05063)