Sony Walkman MZ-E909 User manual

MZ-E909
SERVICE MANUAL
PORTABLE MINIDISC PLAYER
SPECIFICATIONS
US Model
AEP Model
E Model
Tourist Model
Model Name Using Similar Mechanism NEW
MD Mechanism Type MT-MZE909-173
Optical Pick-up Mechanism Type LCX-4E
US and foreign patents licensed from Dolby
Laboratories Licensing Corporation
Ver 1.2 2002.02
with SUPPLEMENT-1
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ= 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW*
* This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.
Revolutions
Approx. 300 rpm to 2,700 rpm
Error correction
ACIRC (Advanced Cross Interleave Reed Solomon Code)
Sampling frequency
44.1 kHz
Coding
ATRAC (Adaptive TRansformAcoustic Coding)
ATRAC3: LP2
ATRAC3: LP4
Modulation system
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
Frequency response
20 to 20,000 Hz ±3 dB
Wow and Flutter
Below measurable limits
Outputs
Headphones/earphones: stereo mini-jack,
maximum output level
5 mW + 5 mW (US model) load impedance
16 ohms,
3 mW + 3 mW (Other models)
load impedance 32 ohms
Power requirements
Nickel metal hydride rechargeable battery
One NH-14WM(A) (supplied): 1.2V, 1,350 mAh
One LR6 (size AA) battery (not supplied)
External power jack (for the rechargeable
battery): Power rating 3V DC
Battery life 1)
(Unit: Approx. hours) (JEITA 2) )
Batteries SP Stereo LP2 LP4
(normal) Stereo Stereo
Ni-MH 38 45 53
rechargeable
battery
NH-14WM(A)3)
LR6 (SG) 60 70 83
Sony Alkaline
dry battery 4)
LR6 (SG)4) and 100 122 145
NH-14WM(A)3)
1) Measured with the power save function on (see
“Preserving battery power”) is on.
2) Measured in accordance with the JEITA(Japan
Electronics and Information Technology
Industries Association) standard (using a Sony
MDW-series Mini-disc).
3) With a fully charged battery
4) When using a Sony LR6 (SG) “STAMINA” alkaline dry
battery (produced in Japan).
Note
The battery operation may be shorter than that
specified, depending on the operating conditions,
the temperature of the location, and the type of
battery being used.
9-873-304-03
2002B0200-1
©2002.02
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation

2
MZ-E909
Specifications ........................................................................... 1
1. SERVICING NOTE...................................................... 3
2. GENERAL
Location and Function of Controls .................................... 4
3. DISASSEMBLY
3-1. “Lid ASSY, Upper”..................................................... 5
3-2. Mechanism Deck ........................................................ 5
3-3. Bracket (R) ASSY ...................................................... 6
3-4. Main Board Sub ASSY, Bracket (L) ASSY,
SW Board ............... 6
3-5. Optical Pick-up ASSY ................................................ 7
4. TEST MODE.................................................................. 8
5. ELECTRICAL ADJUSTMENTS........................... 12
6. DIAGRAMS
6-1. Block Diagram.......................................................... 17
6-2. Printed Wiring Boards – Main Section (1/2) – ......... 18
6-3. Printed Wiring Boards – Main Section (2/2) – ......... 19
6-4. Schematic Diagram – Main Section (1/2) – ............. 20
6-5. Schematic Diagram – Main Section (2/2) – ............. 21
6-6. Printed Wiring Boards – Audio Section – ................ 22
6-7. Schematic Diagram – Audio Section –..................... 23
7. EXPLODED VIEWS
7-1. Main Section............................................................. 26
7-2. Mechanism Deck Section ......................................... 27
8. ELECTRICAL PARTS LIST................................... 28
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINEWITH
MARK !ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS
LIST ARE CRITICALTO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN INTHIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C during
repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
TABLE OF CONTENTS
* Replacement of CXD2671B-206GA (IC601) used in this set
requires a special tool.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
Dimensions
Approx. 71.1 x 77.6 x 12.5 mm (w/h/d) (2 7 / 8 x 3 1 /8 x 1 /2 in.)
(not including projecting parts and controls)
Mass
Approx. 49 g (1.8 oz) (the player only)
Supplied accessories
Headphones/earphones with a remote control
(1)
Battery charging stand (1)
AC power adaptor (for the supplied battery
charging stand)
Rechargeable battery (1)
Rechargeable battery carrying case (1)
Dry battery case (1)
Carrying pouch (1)
AC plug adaptor (1) (world model only)
US and foreign patents licensed from Dolby Laboratories.
Design and specifications are subject to change without notice.
rUNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the
lead-free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed
with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to
be applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set
to about 350°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder
may also be added to ordinary solder.
Ver 1.1 2001.11
MAIN BOARD SUB ASSY
• Audio board is supplied with main board sub ASSY.
• Audio board can't be moved away from main board.
Give a damage when take it off forcibly.
• The part that audio board overlap with main board can't be re-
paired.

3
MZ-E909
SECTION 1
SERVICING NOTE
When repairing this device with the power on, if you remove the main board, this device stops working.
In this case, you work without the device stopping by fastening the hook of the Open/Close detection switch (S809).
Open/Ciose detection switch (S809)

4
MZ-E909
SECTION 2
GENERAL
This section is extracted from
instruction manual.
To
Find the beginning of
the current track or
the previous track
3)
Find the beginning
of the next track
4)
Go backwards
while playing
Go forward
while playing
Pause
Remove the MD
2)
You can turn off the beep sound. For more details, see “Turning off the beep sound.”
3)
f you turn the control towards . on the remote control (or press . on the player) during the
first track of the disc, the player goes to the beginning of the last track on the disc.
4)
f you turn the control towards N> on the remote control (or press > N on the player) during
the last track of the disc, the player goes to the beginning of the first track on the disc.
5)
f you open the lid, the playback will begin from the beginning of the first track (except when disc
information is stored to the personal disc memory or when group mode is on).
z
The MZ-E909 supports the newly developed DSP TYPE-R for ATRAC.
t thus allows you to enjoy TYPE-R high-quality sound from MDs recorded in SP stereo on TYPE-R-
equipped MD decks, etc.
Note
When removing the disc, make sure to press x first, and then slide OPEN.
Viewing the display window of the remote control
Track number Track name
6)
or elapsed time of the track
6)
Appears only with MDs that have been electronically labeled.
z
• The player can play the track recorded by 2 × or 4 × long playing mode (LP2 or LP4). Normal stereo
playback, LP2 stereo playback, LP4 stereo playback or monaural playback is automatically selected to
match the audio source.
• The display on the remote control will turn off shortly after you press x.
Do this (Beeps
2)
in the headphones)
Turn the control towards . on the remote control once
(three short beeps). (Or press . on the player once.)
Turn the control towards . on the remote control repeatedly
(continuous three short beeps). (Or press . on the player
repeatedly.)
Turn the control towards N> on the remote control (two
short beeps).
Press > N on the player once.
Turn and hold the control towards . on the remote control.
Hold down . on the player.
Turn and hold the control towards N> on the remote control.
Hold down > N on the player.
Press X on the remote control (continuous short beeps).
Press X on the remote control again to resume play.
Press x, and then slide OPEN.
5)
Playing an MD
Insert an MD.
1
2
3
Play an MD.
2
x
X
1N>
VOL+
VOL–
.
> N
.
VOLUME +/–
GROUP
x
1Turn the control towards N> on the remote control (or press > N
on the player) to play the disc.
A short beep sounds in the headphones/earphones when using the remote control.
The LED flashes and then lights up.
2Pull and turn VOL +/– on the remote control (or press VOLUME +/– on the
player) to adjust the volume.
The volume indicator appears in the display, allowing you to check the
volume level. After you adjust the volume, push back the control.
To stop play, press x.
Playback starts from the point you last stopped playing. To start playback from the
beginning of the disc, turn and hold the control towards N> on the remote control
(or hold down > N on the player) for 2 seconds or more.
1)
The LED indicates the current operating status by the lighting up in the following colors.
When the battery power is exhausted, the LED starts flashing. For more details, see
“When to replace or recharge the battery.”
LED color Operating status
Red Normal play (The LED lights up continuously)
Green Group mode* (The LED lights up continuously)
Orange Group skip mode* (The LED lights for about 5 seconds)
*For more details, see “Using the group function.”
1
2
Insert an MD with the label side facing up, pushing the
MD to the direction of the arrow in the illustration.
1 Slide OPEN to open the lid. 2 Insert an MD. 3 Close the lid.
3 Color Info-LED1)
The Player
1
9
7
F
E
C
D
2
8
1./x/ N> button
23 Color nfo-LED
3GROUP button
4HOLD (Locking the control) switch
5i (earphones) jack
6OPEN switch
7Terminals for charging stand/
dry battery case (at the bottom)
8VOL +/– button
9Battery compartment
The earphones with a remote
control
J
+
–
H
I
K
D
A
L
F
B
E
G
C
1Headphones/earphones
2Stereo mini plug
3X (pause) button
4SOUND button
5RPT/ENT (Repeat/Enter) button
6PLAYMODE button
7D SPLAY button
8x (stop) button*
9Control (./
N> )
q; Control VOL +/–
Pull and turn to adjust the volume.
qa HOLD (Locking the control) switch
qs Display window
* The stop button also operates as the enter
button, depending on the function.
The display window of the remote
control
F
G
ABCDE
1Track number display
2Charactor information display
3Disc indication
4Alarm indication
5Play mode indication
6Battery level indication
7SOUND indication
The battery charging stand
B
A
C
1Terminals for charging
2CHARGE lamp
3DC N (3V jack) (at the rear)

5
MZ-E909
SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.
3-1. “LID ASSY, UPPER”
3-2. MECHANISM DECK
rThe equipment can be removed using the following procedure.
2
1 Screws , ES Lock
1 Screws , ES loc
k
Bracket (L) ASSY
Lid ASSY, upper
4
7
5
2
9 Motor flexible board
(CN551)
6 Claw
8 OP flexible board
(CN501)
1 Move claw away from
bracket (stop) ASSY
3 Screw (LL), step
Bracket (stop) ASSY
Panel, bottom
Bracket (R) ASSY
Mechanism deck
“Lid ASSY Upper”
Set
Optical pick-up ASSY
Mechsnism deck
Bracket (R) ASSY
Main board sub ASSY
Bracket (L) ASSY,
SW board
Ver 1.1 2001.11

6
MZ-E909
Note : On installation of bottom panel assy, adjust the position of
both two switches (S807, S808) and two knobs (AVLS,
HOLD).
3-3. BRACKET (R) ASSY
3-4. MAIN BOARD SUB ASSY, BRACKET (L) ASSY,
SW BOARD
2
3 Screw, ES lock
1 Screw, ES lock
1 Screw, ES lock
1 Screws, ES lock
3 Screw, ES lock
Panel, bottom
Bracket (L) ASSY
Bracket (R) ASS
Y
Ver 1.1 2001.11
6
4
7
1
Knob (HOLD)
Main board sub ASS
Y
(Audio board)
Bracket (L) ASSY
SW board
Case (K), battery
5 Remove solder
(Two places)
3 Lid, battery case
2 Claw
MAIN BOARD SUB ASSY
• Audio board is supplied with main board sub ASSY.
• Audio board can't be moved away from main board.
Give a damage when take it off forcibly.
• The part that audio board overlap with main board can't be re-
paired.

7
MZ-E909
3-5. OPTICAL PICK-UP ASSY
5
3 Screw (MI 1.4)
4 Spring, thrust deten
t
1 Washer
2 Gear (SA)
Optical pick-up ASSY
(LCX-4E)

8
MZ-E909
Remote control LCD
• Press and hold down Xto hold the current display while the
key is being pressed.
4-2-3. How to release the TEST MODE
When method 1was used:
Turn off the power and open the solder bridge on TAP601 on the
main board.
Note: The solder should be removed clean. The remaining solder
may make a short with the chassis and other part.
When method 2was used:
Turn off the power.
Note: If electrical adjustment (see page 11) has not been finished
completely, always start in the test mode. (The set cannot
start in normal mode)
4-3. TEST MODE STRUCTURE
4-1. GENERAL
• When entered in the TEST MODE, this set provides the Overall
Adjustment mode which allows CD and MO discs to be auto-
matically adjusted. In the Overall Adjustment mode, the system
discriminates between CD and MO discs, performs adjustments
in sequence automatically, and displays the faulty location if
any fault is found. In the Manual mode, selected adjustments
can be performed automatically.
• The attached remote control is used to operate the TEST MODE.
Unless otherwise specified in the text, the key means that on the
remote control.
4-2. SETTING THE TEST MODE
4-2-1. How to set the TEST MODE
To set the TEST MODE, two methods are available.
1Solder bridge and short TAP601 (TEST) on the main board.
Then turn on the power.
MAIN BOARD (SIDE A)
2In the normal mode, operate the keys on the set and those on the
remote control as specified below:
Turn on HOLD switch on the set. Holding down x (STOP)
key on the set, press the keys on the remote control in the
following sequence:
> N t> N t.t.t> N
t.t> N t.tXtX
4-2-2. Operations when the TEST MODE is set
When the TEST MODE is entered, the system switches to the dis-
play check mode within the TEST MODE. From this mode, the
other Test modes can be accessed.
When the TEST MODE is set, the LCD repeats a cycle of the fol-
lowing displays:
SECTION 4
TEST MODE
888
u
008 V1.000
F 1SHUFF PGM
SOUND 1 2 BASS 1 2
All on
All off
Microprocessor
version
display
Test Mode
(Display Check Mode)
Manual Mode
Servo Mode
Audio Mode
Power Mode
OP Alignment Mode
key
key
+
key
+
key
x
x
>B
key
key
xkey
.or
key
xkey
Overall Adjustment Mode
Sound Skip Check Result Display Mode
Self-diagnostic Display Mode
Key Check Mode
DISPLAY key
DISPLAY key
(Press and hold down about 3 sec)
Terminate key checking or open
the top panel.
C613 C605
C810
C802
C699
R607 R601 R8
0
C606
C610
TP921
SHORT: TEST MODE
OPEN: NORMAL MODE
TAP601

9
MZ-E909
2. During each test, press and hold down > N key or .
key for a while to move the optical pickup on the sled outer or
inner perimeter.
3. Each test item is assigned with a three-digit item number. The
100th place is a major item, 10th place is a middle item, and unit
place is a minor item.
Note: In the Power mode, the item title display is only displayed.
5. To terminate the Manual mode and return to the TEST MODE,
press xkey.
4-5. OVERALL ADJUSTMENT MODE
4-5-1. Outline of the function
This mode is designed to adjust the servo system automatically by
going through all the adjustment items.
Usually, this mode is used to perform automatic adjustments when
servicing the set.
For further information, refer to section 5. ELECTRICALADJUST-
MENTS. (See page 12)
4-6. SELF-DIAGNOSTIC DISPLAY MODE
4-6-1. Outline of the function
The Self-diagnostic system is used in this set. If an error occurs
during playback, this system detects the fault through the
microprocessor’s mechanism and power control blocks and stores
the cause in EEPROM in a history format.
This history, which can be viewed in the TEST MODE, provides
the means of locating the fault in troubleshooting.
4-4. MANUAL MODE
4-4-1. Outline of the function
The Manual mode is designed to perform adjustments and
operational checks on the set’s operation according to each
individual function.
Usually, no adjustments are made in this mode.
However, the Manual mode is used to clear the memory before
performing automatic adjustments in the Overall Adjustment mode.
4-4-2. How to set the Manual mode
1. Set the TEST MODE and press + key to set the Manual mode.
Remote control LCD display
4. During each test mode, the display is changed from one to
another each time DISPLAY key is pressed.
• Address & Adjusted Value Display
LCD display
• Jitter Value & Adjusted Value Display
LCD display
• Block Error Value & Adjusted Value Display
LCD display
• ADIP Error Value & Adjusted Value Display
LCD display
• Item Title Display
LCD display
000 Manual
Change Major
Item
Change Middle
Item
Change Minor
Item
Change Adjustment
Value
Write Adjustment
Value
.
key : 100th place of mode number
increase
+
key : 100th place of mode number
decrease
key : 10th place of mode number
increase
+
key : 10th place of mode number
decrease
key : Up
+
key : Down
key : When adjusted value is changed :
Adjusted value is written.
When adjusted value is not changed :
That item is adjusted automatically.
keykey
x
key
x
> N
key
> N
key : Unit place of mode number
increase
key : Unit place of mode number
decrease
> N
X
011 C68S01
address
mode number
adjusted value
011 OFFJ01
jitter value
mode number
adjusted value
011 063B01
block error value
mode number
adjusted value
011 059A01
ADIP error value
mode number
adjusted value
011 LrefPw 0 1
item title
mode number
adjusted value

10
MZ-E909
4-6-2. Self-diagnostic mode
1. Set the TEST MODE.
2. With all the LCD display segments blinking on the set, press
DISPLAY key and >B key, the Self-diagnostic mode is
entered.
3. Hereinafter, each time > N key is pressed, the reference
information display changes as follows:
• Press .key to go back to the previous display.
• Contents of the history codes
History code number Contents
1 The first error that occurred.
N The last error that occurred.
N-1 The first error from the last one.
N-2 The second error from the last one.
RTotal recording time ( – – – – is displayed
for MZ-E909)
Contents of fault Display code Meaning of code Simplified Description
contents
No error 00 No error – – – – No error
01 Access target address illegally specified Adrs An attempt to access an abnormal address.
Servo system error 02 HIGH TEMP Temp HIGH TEMP
03 FOCUS ERROR Fcus Focus off-center.
04 SPINDLE ERROR Spdl Abnormal rotation of disc
11 TOC ERROR TOC
TOC error 12 READ DATA ERROR Data
Power system error 22 LOWBATT LBat Instantaneous interruption detected.
31 OFFSET ERROR Ofst Offset error
Offset error 32 FE_ABCD_OFFSET_ERR ABCD FE ABCD Offset error
33 TE_ABCD_OFFSET_ERR TE TE ABCD Offset error
34 X1_TE_OFFSET_ERR X1TE X1 TE ABCD Offset error
001 1 Adrs
History code
Error display code
Simplified contents
0XX 1 # ###
0XX # ###
0XX 1 # ###
0XX 2 # ###
0XX R ––––
•Description of the error display codes
4-6-3. Clearing the error display code
After servicing, reset the error display code.
1. Set the TEST MODE.
2. Press the DISPLAY key on the remote control activates the self-
diagnosis display mode.
3. To reset the error display code press Xkey on the remote con-
trol when the code is displayed.(except for R - - - - display)
(All the data on the 1st, N, N-1 and N-2 will be reset)
4. Press Xkey on the remote control again.

11
MZ-E909
4-8. KEY CHECK MODE
4-8-1. Outline of the function
This mode is used to check to make sure that each of the keys
(including the slide switch) on the set operates normally.
4-8-2. Setting the Key Check mode
1. Set the TEST MODE. Press and hold down DISPLAY key (for
more than 3 sec) to set the Key Check mode.
LCD display
2. When each key on the set and on remote control is pressed, its
name is displayed on the LCD. (The operated position is dis-
played for 4 sec after the slide switch is operated. If any other
key is pressed during this display, the LCD switches to its name
display)
Example: When > N key on the set is pressed:
LCD display
Example: When > N key on the remote control is pressed:
LCD display
XX: AD value of the remote control key (hexadecimal 00 to FF)
3. When all the keys on the set and on the remote control are con-
sidered as OK, the following displays are shown for 2 sec.
(The key pressed to enter the Key Check mode has been checked
even if it is not pressed in this mode)
Example: When the keys on the set are considered as OK:
LCD display
Example: When the keys on the remote control are considered
as OK:
LCD display
4. When all the key have been checked or when the top panel is
opened during this checking, the system terminates the Key
Check mode and return to the TEST MODE.
000 0F
4-7. SOUND SKIP CHECK RESULT DISPLAY MODE
This set can display and check the error count occurring during
play.
•Setting method of Sound Skip Check Result Display Mode
1. Setting the test mode.
2. Press the > N key activates the sound skip check result
display mode where the LCD displays as shown below.
LCD display
3. When > N key is pressed, the total of error count is dis-
played on the LCD, and each time the > N key is pressed,
the error count descents one by one as shown below. Also, when
. key is pressed, the error count ascends by one.
P**R00 : Total of play system error and record system error count
** : Sound skip check items counter (hexadecimal)
##### : 6-digit address (hexadecimal) where a sound skipped
Error code
Cause of error Description of error
Playback EIB Sound error correction error
Stat Decorder status error
Adrs Cannot access the address
BEmp Buffer becomes empty
4. Quit the sound skip check result display mode, and press the x
key to return to the test mode. (display check mode)
000 P**P##
Total of record system error count
Total of play system
error count
000 P**R00
000 EIB **
000 Stat**
000 Adrs**
000 BEmp**
000 ######
000 FF 0F
000 rPLAY XX
888 SET OK OF
888 RMC OK OX

12
MZ-E909
C910
R910
R951
R965
R964
R909
R903
C909
C921
C908
C905
L905
C907
10
14
15202528
29
30 IC901
D903
TP901
(VC)
TP901 (VC)
digital voltmeter
5-4. MANUAL POWER ADJUSTMENTS
5-4-1. Adjustment sequence
The adjustments should be always performed in the following se-
quence:
1Vc PWM Duty (L) adjustment (item No.:762)
r
2Vl PWM Duty adjustment (item No.:764)
r
3Vd PWM Duty adjustment (item No.:765)
5-4-2. Vc PWM Duty (L) adjustment method
1. Confirm that the power voltage is at 1.5 V DC.
2. Set the TEST MODE.
3. Set the overall adjustment mode and press PLAY MODE key,
item No. will change to 762.
LCD display
SECTION 5
ELECTRICAL ADJUSTMENTS
5-1. GENERAL
In this set, CD and MO discs can be automatically adjusted by set-
ting the Overall Adjustment mode within the TEST MODE,
Before performing these automatic adjustments, it is necessary to
clear the memory and adjust the power in the Manual mode.
5-2. NOTES FOR ADJUSTMENT
5-2-1. Jigs
• CD disc TDYS-1 (part code: 4-963-646-01)
• MO disc PTDM-1 (part code: J-2501-054-A)
or commercially available MO disc (recorded)
• Digital voltmeter
5-2-2. Adjustment sequence
The adjustments should be always performed in the following
sequence:
5-2-3. Power
The power is supplied with 1.5 V DC from the battery case.
5-3. RESET NV
5-3-1. How to reset NV
1. Set the TEST MODE.
2. Set the Manual mode and set the item No. 021, Reset NV.
LCD display
1Reset NV (Clear the memory)
2Manual power adjustments
3Electrical offset adjustments
(Do not enter the disc)
4Overall CD adjustments
5Overall MO adjustments
6RESUME clear
7Rewrite the NV value
Overall adjustment mode
Manual mode
3. Press Xkey on the remote control.
LCD display
4. Press Xkey on the remote control again.
LCD display
5. Press xkey to terminate the Manual mode and return to the
TEST MODE.
021 Res NV CC
021 Res OK?
021 Res ***
021 Reset!
After reset is completed.
4. Connect a digital voltmeter to TP901 (VC) on the main board
and adjust + key (voltage up) and –key (voltage down) on
the remote control.
Adjustment value:2.35V
Standard value:2.34 to 2.355V
MAIN BOARD (SIDE A)
762 VclPWM XX
5. Press Xkey to write the adjustment value.

13
MZ-E909
5-4-3. Vl PWM Duty adjustment method
1. Set the Manual mode and set the item No. to 764.
LCD display
2. Connect a digital voltmeter to TP917 (VL) on the main board
and adjust + key (Voltage up) and –key (Voltage down) on
the remote control.
Adjustment value:2.23V
Standard value:2.22 to 2.235V
MAIN BOARD (SIDE A)
3. Press Xkey to write the adjustment value.
5-4-5.Electrical offset adjustment method
Note: Doing adjustment by the state that a disc does not enter.
1. Confirm the power voltage is 1.5V.
2. Set to the test mode.
3. Press the –key activates the overall adjustment mode.
LCD display
4. Press the DISPLAY key.
LCD display
5. If result of electrical offset adjustment is OK,the following dis-
play appears.
LCD display
5-5. OVERALL ADJUSTMENT MODE
5-5-1. Overall adjustment mode structure
Note: The overall adjustments should be always performed in the
sequence of CD tMO adjustments.
5-5-2. Overall CD and MO adjustment method
1. Set the TEST MODE and press –key to set the Overall Ad-
justment mode.
LCD display
2. Insert CD disc in the set, and press .key to set the Overall
CD Adjustment mode.
Automatic adjustments are made.
LCD display
XXX: Item No. for which an adjustment is being executed.
5-4-4. Vd PWM Duty adjustment method
1. Set the Manual mode and set the item No. to 765.
LCD display
2. Connect a digital voltmeter to TP903(VD) on the main board
and adjust + key (Voltage down) and –key (Voltage up) on
the remote control.
Adjustment value:1.26V
Standard value:1.255 to 1.27V
MAIN BOARD (SIDE A)
3. Press Xkey to write the adjustment value.
765 VD_PWM XX
764 VlPWM XX 000 Assy11
030 Ofst**
030 OfstOK
TEST MODE
(Display Check Mode)
Overall Adjustment
Title Display(ASSY**)
CD overall
Adjustment
.
key
VOLUME – key
key
x
MO overall
Adjustment
> N
key
> N
key
key
x
Electrical offset
Adjustment key
DISPLAY key key
x
key
x
Power Supply
Adjustment
PLAY MODE key
XXX CD RUN
000 Assy11
R930
D901
D902
C903
C901
L902
TP917
(VL)
Q901
C E
TP917
(VL)
digital
voltmeter
C603
C526
R807
R827
R
R806
R515
R808
C807
C559
C558
C557
C601C806
Q501 1
434550
55
56
42
TP604
TP602
TP601
TP533
TP603
IC801
1
4
8
5
RB553
45
1
CN551
TP903
(VD)
R805
C805
C604
C529
digital
voltmeter
TP903(VD)

14
MZ-E909
3. If NG in the overall CD adjustments, return to Reset NV and
perform from the electrical offset adjustment again.
LCD display
XXX: NG item No.
4. If OK through the overall CD adjustments, then perform overall
MO adjustments.
LCD display
5. Insert MO disc in the set, and press > N key to set the
Overall MO Adjustment mode. Automatic adjustments are made.
LCD display
XXX: Item No. for which an adjustment is being executed.
6. If NG in the overall MO adjustments, return to Reset NV and
perform the adjustment again.
LCD display
XXX: NG item No.
7. If OK through the overall MO adjustments, press xkey to
return to the TEST MODE and terminate the Overall Adjust-
ment mode.
LCD display
5-5-3.Resume clear method
1. Setting the testmode.
2. Set the Manual mode and set the item No.043(RESUME Clear).
LCD display
3. Press the Xkey.
LCD display
5-5-5. Overall CD and MO adjustment items
1. Overall offset adjustment
Item No. Contents
030 GRV setting • Sarvo OFF • Head UP
035 Laser ON/OFF electrical offset difference
measurement
Completed
2. Overall CD adjustment items
Item No. Contents
761 VC,VR power voltage High/Low selection
300 HPIT setting • Sarvo OFF
561 SLED move to inside
562 SLED move to outside
High reflection CD electrical offset adjustment
312 Laser ON • Focus UP • VC correction ALFA offset
adjustment
313 IJ offset adjustment
314 FE offset adjustment
HPIT adjustment
320 Focus servo ON
324 TE offset adjustment 1
321 TE gain adjustment
328 TWPP gain adjustment
324 TE offset adjustment 1
332 TE offset adjustment 2
330 Tracking servo ON
336 ABCD gain adjustment
337 KF gain correction
338 RF gain adjustment
344 CD focus gain adjustment
345 CD tracking gain adjustment
521 CD two-axis sensitivity adjustment (inside)
522 CD two-axis sensitivity adjustment (outside)
341 CD focus bias adjustment
300 HPIT setting • servo OFF
completed
XXX NG
XXX CD OK
XXX MO RUN
000 MO OK
000 XXX NG
043 Resume CC
043 Res ***
043 Res Clr
After reset is completed
LCD display
3. Overall MO adjustment items
Item No. Contents
761 VC,VR power voltage High/Low selection
100 G RV setting
Low reflect MO offset adjustment
112 Laser ON • Focus UP • EVC correction ALFA offset
adjustment
113 IJ offset adjustment
114 FE offset adjustment
118 Wpp denominator adjustment
HPIT adjustmet
200 LPIT setting • servo OFF
561 SLED move to inside
220 Focus servo ON
224 TE offset adjustment 1
221 TE gain adjustment
224 TE offset adjustment 1
232 TE offset adjustment 2
5-5-4. Rewrite the NV value
After resume clear, rewrite the NV value.
Microprocessor version 1.0 to 2.0 : Step 1 and 2.
Microprocessor version 2.1 and later : Step 1 only
Step Item NO. NV value
1861 0F (h)
862 0B (h)
2863 87 (h)
864 75 (h)

15
MZ-E909
Item No. Contents
230 Tracking servo ON
236 ABCD gain adjustment
237 KF gain adjustment
238 RF gain adjustment
244 FCS gain adjustment
245 TRK gain adjustment
READ GRV adjustment 1
100 R GRV setting
562 SLED move to outside
120 Focus servo OFF
122 TON offset adjustment
121 TE gain adjustment
122 TON offset adjustment
123 TEIN offset adjustment
124 TWPP offset adjustment
130 Tracking servo ON
131 TWPP offset adjustment
136 ABCD gain adjustment
137 KF gain adjustment
139 ADIP BPF fo adjustment
144 FCS gain adjustment
145 TRK gain adjustment
134 TWPP gain adjustment
131 TWPP offset adjustment 1
132 TWPP offset adjustment 2
149 TWPP OP offset adjustment
138 RF gain adjustment
100 R GRV setting • Servo OFF

16
MZ-E909 SECTION 6
DIAGRAMS
rWAVEFORMS
1
IC501 1 TE
2
3
IC501 ed (RF)
IC501 rs (FE)
Note on Schematic Diagram: MAIN SECTION
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ωand 1/4W or less unless otherwise
specified.
•f: internal component.
Note: The components identified by mark 0or dotted
line with mark 0are critical for safety.
Replace only with part number specified.
•: B+ Line.
• Power voltage is dc 1.5V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : PLAY
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F: Analog
J: Digital
•Replacement of IC601 used in this set requires a special
tool.
•The voltage and waveform of CSP (chip size package)
cannot be measured, because its lead layout is different
form that of conventional IC.
Note on Printed Wiring Boards: MAIN SECTION
•X: parts extracted from the component side.
•: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side: Parts on the pattern face side seen from the
(Side B) pattern face are indicated.
Parts face side: Parts on the parts face side seen from the
(Side A) parts face are indicated.
• Main boards is four-layer pritnted board.
However, the patterns of layer 2 and 3 have not been
included in this diagrams.
•Replacement of IC601 used in this set requires a special
tool.
•Lead Layouts
Lead layout of
conventional IC
surface
CSP (chip size package)
Approx.
12 mVp-p
Approx.
1.2 Vp-
p
Approx.
10 mVp-p
MAIN BOARD SUB ASSY
• Audio board is supplied with main board sub ASSY.
• Audio board can't be moved away from main board.
Give a damage when take it off forcibly.
• The part that audio board overlap with main board can't be re-
paired.
Ver 1.1 2001.11

MZ-E909
17 17
6-1. BLOCK DIAGRAMS
• Signal path.
F: Analog
J: Digital
12
160
161
9
202
194
195
221 XRF RST
PDS1
XCS NV
SI0
SCK0
S00
XTEST
PD S0
S MON
SSB CLK
SSB DATA
VREF MON
MUTE
XHP STB
BEEP
142
RMC DTCK
13
SET KEY 1
17
WK DET
227
HOLD SW
20
RMC KEY
VC PWM
164
165
VL PWM
86
FS4
235
SLEEP
236
FFCLR
8
XRST
21
AVDD
5
2
CLK
INM2
INM1
RF2
RF1
VRMC
XWK3
VSTB
XWK1
XWK4
VD
XRST
10
44
VLD
19
VG
18
LG
9
VL
11
VL
16
12
L2
L2
50
VB
28
L1
32
L1
33
VC OUT
7
26
27
22
23
56
4
6
XWK2
3
SLEEP
55
FFCLR
54
46
VC
36
VC
34
VC2
45
21
1
20
13
4
24
23
BEEP
STB
MUTE
BEEP OUT A
BEEP OUT B
OUT B
RCH
RCH
IN B
+B
VCC
VREF IN
UNREG
VIF
REFERENCE
VOLTAGE
SWITCHING
Q301
LED
SWITCH
Q803
LED
SWITCH
Q801
22 2
i
J301
RCH LCH
KEY
RGND
DATA
VC
OFF ON
S808
D801,802
(3 COLOR LED)
HOLD
S805
VOLUME
+
S806
GROUP
S804
VOLUME
-
S809
(OPEN/CLOSE)
VL
DVDD
35
VCO
VC
42
VIF
VIF
41
VA
AVDD
DVDD
DVDD
VG
UNREG
UNREG
234
VLON VLON
1
HEADPHONE AMP
IC301
POWER SUPPLY
IC901
-
89
87
88
SPD U
SPD V
SPVS
220 XRST MTR DRV
17
18
15
S803
.
S801
x
S802
>N
D901
D902
D903
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
1PC, 1.5V
VB MON
REC KEY
SET KEY2
TSB MST VDD
10
19
HALF LOCK SW
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER,
16M BIT D-RAM, SYSTEM CONTROL
IC601
TAP601
(TEST)
141
LED O 211
LED RED PWM 167
LED GREEN PWM 163
18
14
VC
AUDIO BOARD (1/2)
AUDIO BOARD
(2/2)
SW BOARD
183
218
240
MAIN BOARD
37
44
45
46
47
56
74
78
49
29
30
73
84
91
113
153
222
23
119
139
151
231
6
59
33
29
28
41
42
1
44
21
31
43
24
23
4
8
9
10
11
12
14
5
6
13
7
18 19
LASER
AUTO POWER
CONTROL
Q501
3
4
2
19
11
20
13
12
5
18
9
10
14
15
16
17
7
8
6
1
TRACKING
COIL
FOCUS
COIL
20
Jx Jy Jx
Ix Iy
Iy
Ix
Jx
Jy
A
B
C
D
PD
Ix
a
F
bcd
MINIDISC
OPTICAL PICK-UP BLOCK
(LCX-4E)
LD
AVCC
S0
S1
AVCC
S0
LD-K
LD-A
MON
D
C
B
A
Jy
Jx
Ix
Iy
D
D-C
PD-I
PD-O
C
B
A
VREF
VREF
A-C
Jy
Jx
Ix
Iy
S1
RF AMP,
FOCUS
ERROR,
TRACKING
ERROR
TPP/WPP
APC
SERIAL
I/F
AVCC
22
40
DVDD
AVCC
VIF
RF OUT
PEAK
BOTM
ABCD
FE
ADIP IN
TE
ADIP
PD-NI
VC
AOUT L
AOUT R
VDIOSC
DRAMVDD0
DSPVDD0
DSPVDD1
MCUVDD1
DSPVDD2
DSPVDD3
MCUVDD2
MCUVDD3
DRAMVDD1
JTAGVDD
FLASHVDD
MCUVDD0
SBUS
SCK
S MON
XRST
PEAK
/BOTM
RFI
PEAK
BOTM
ABCD
FE
TE
VC
ADFG
APCREF
VC
DVDD
RF AMP,FOCUS/TRACKING ERROR AMP
IC501
CN501
TRK+
TRK-
FCS+
FCS-
30
95
94
93
102
99
97
96
98
83
82
101
196
176
100
76
143
154
210
241
24
25
26
23
33 28
27
81
80
47
14 15
16
42
43
44
34
35
37
8
9
6
5
4
UNREG
52
41
HI-BRIDGE
CONTROL/
PRE DRIVER
HI-BRIDGE
CONTROL
PRE
DRIVER
3 PHASE
CONTROL/
PRE DRIVER
3 PHASE
CONTROL/
PRE DRIVER
PRE
DRIVER
PRE
DRIVER
PRE
DRIVER
24 46
25 45
53
54
1
56
55
48
FOCUS/TRACKING COIL DRIVE,
SPINDLES/SLED MOTOR DRIVE
IC551
SLCU
DIFVDD0
VIF
TSB SLV VDD
MIFVDD0
MIFVDD1
MIFVDD2
TSB SLV CHK
MIFVDD3
SLCV
OSCI
TFDR
OSCO
TRDR
FRDR
SLDV
SRDR
SFDR
SLDW
SLCW
SPCU
SPCV
SPCW
FFDR
X601
45.1584MHz
SLED1+
SLED1-
SLED2+
SLED2-
CLVU
CLVV
CLVW
MINIDISC
MECHANISM BLOCK
M902
(SLED)
M901
(SPINDLE)
4
2
3
1
8
7
6
5
CN551
32
13
39
17
20
19
18
90 SPD W
2
BIAS
OE
11
S-MONITOR
25
RECHAGEABLE
BATTERY
NH-14WM
1PC, 1.2V 1400mAh
219
EEPROM
IC801
4DI 3DO 2SK 1XCS
181
180
179
D802 (ORANGE)
D801
(RED)
(GREEN)
SWITCH
Q901
DVDD
ON/OFF
Q907,908
DVDD
SWITCH
Q906
DVDD
SWITCH
Q909
DVDD
SWITCH
Q905
DC-DC
CONVERTER
Q902
IC902

MZ-E909
18 18
D101 E-7
D201 F-8
D855 D-7
D901 B-2
D902 A-3
D903 C-3
D904 E-4
IC501 E-5
IC551 E-6
IC601 B-7
IC801 D-7
IC901 C-2
IC902 E-4
Q501 D-5
Q801 E-7
Q803 D-8
Q901 B-3
Q902 E-4
Q905 E-6
Q906 F-7
Q907 E-7
Q908 E-6
Q909 F-6
23 4 5 6 7 8 9
A
1
B
C
D
E
F
C505
C519
C530
C503 R503
R519
C854
C853
C603
C526
C613 C605
C810 C802
C616
C607
C699
C612
C611
C515
C513 C511 C510
C508
C910
R910
R951
R965
R807
R827
R615
R603 R606 R605 R614 R612
R607 R601
R602
R804
R501
R521
R516
R505
R921
R948
R920
R964
R950
C920
R909
R930
R903
R818
R817
C851
R819
R806
R515
R808
R613
R609
R526
R517
R525
C807
C559
C558
C557
C601C806
C615
C509
C516
C504
C501
C502
C918
C924
C915
C909
C921
C908
C905
Q501
BCE
D901
D902
C903
C901
L503
L904
L905
L901
L902
L903
MAIN BOARD (SIDE A)
C606
C610
C524
C922
C904
C919
C923
C925
C907
1
5
10
14
15202528
43
29
30
35
40
45 50 5556
42
IC901
1
5
10
14
15 20 25 28
43
29
30
35
40
4550
55
56
42
IC551
IC501
IC902
1
1
5
13
54
5
10
10
15
15
20
20
22
44403530
25
23
CN501
OPTICAL PICK-UP
BLOCK
LCX-4E
X601
*
IC601
TP921
TP604
TP605
TP565
TP560
TP602
TP601
TP533
TP603
SHORT: TEST MODE
OPEN: NORMAL MODE
TAP601
FB801
FB802
IC801
1
15 15
210
19
20
4
8
5
RB553
RB554
D855
3
2
1
45
CN801
AAUDIO BOARD
CN802
D201
D903
D101
M
M902
SLED MOTOR
M901
SPINDLE MOTOR
1
2
3
4
5
6
7
8
J301
2
1
5
8
CN551
11
(11)
1-682-467-
C618
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION LR6)
1PC, 1.5V
11
1-679-187-
MOTOR FLEXIBLE BOARD
RECHAGEABLE
BATTERY
NH-14WM
1PC, 1.2V 1400mAh
TP903
(VD)
TP917
(VL)
TP901
(VC)
Q901
B C E
S
D
G
Q902 D904
C563 C564 C565
C527
R805
R839
R832 R831
R833 R830
R834
R835
R958 R959
R962
R960
R961
R931
R932 R933
C805
C604
C999
C952
Q909
Q801
G
S
D
Q905
Q906
SD
G
ECB
Q908
Q907
BCE
C529 BCE Q803
6-2. PRINTED WIRING BOARDS – MAIN SECTION (1/2) – zRefer to page 16 for Notes.
Ref. No. Location
zSemiconductor
Location

MZ-E909
19 19
6-3. PRINTED WIRING BOARDS – MAIN SECTION (2/2) – zRefer to page 16 for Notes.
23 4 5 6 7
A
1
B
C
D
E
F
MAIN BOARD (SIDE B)
11
(11)
1-682-467-
TP611
TP612
TP613
TP615
TP616
TP613
TP559 TP562
TP563
TP609
TP610
TP607
TP558
TP606
TP552
TP556
TP561
TP564
TP608
TP557
TP551
TP104
TP204
TP810
TP811
TP812
TP813
TP302 TP203
TP103
TP570
TP572 TP573
TP571
TP526
TP952
TP525
TP532
TP524
TP530
TP523
TP527 TP528
TP529 TP521
TP501
TP502
TP591
TP516
TP919
TP907
TP902
TP920
TP912
TP911
TP904
TP519
TP517
TP513
TP514
TP515
TP510
TP511
TP512
TP507
TP508
TP509
TP577
TP576
TP557
TAP501
TP574 TP567
TP566
TP503
TP505
TP504
TP506

MZ-E909
20 20
6-4. SCHEMATIzC DIAGRAM – MAIN SECTION (1/2) – zRefer to page 16 for Notes. z Refer to page 16 for Waveforms. z Refer to page 24 for IC Block Diagrams.
C505
C502
TP5105
C503
TP5118
TP5112
C508 R525
IC501
R526
C511
C510
C516
C501
R501
C509
Q501
C529
R521 R519
C527 R517
R516
C530
R505
C802
C611
C607
C612
R605
R606
C613
C610
C616
R613
C603
C604
C601
R808
C806 C807
CN501
R806
R603
X601
TAP601
R827
CN801
L503
10µH
C526
C524
R503
C513
R804
C605
R607 R615
C519
C504
C515
R614
C615
R612
R601
IC801
R609
C618
R602
C606
IC601
R805
R807
R831
R833
Q801 Q803
R839
C805
C810
R830
R834
R832
R835
R515
0.01
0.033
(GND)
3300p
1500p 0
SN761057DBT
0
10p
10p
0.1
100p
33k
3300p
2SA1577
10
6.3V
1100k
0.033 2.2k
2.2k
2200p
2.2k
0.1
0.01
1
0.47
10k
100k
470p
10
6.3V
0.1
220
0.1
0.1
0.1
3.3k
0.047 0.047
20P
100k
150
45.1584MHz
1M
20P
0.033
10
6.3V
1k
10p
47k
1
100k 3.3M
3300p
3300p
0.1
1k
0.1
3.3k
10
AK6417AL
220k
1
10
10
6.3V CXD2671B-206GA
3.3k
3.3k
330
15k
XP1510 UN9214J
470
0.1
0.01
68k
470k
33
470k
2.2k
1
217
16
14
13
9
8
7
6
5
412 15 18
11
TRK-
TRK+
FCS-
FCS+
VREF MON
ADIP
PEAK
BOTM
FE
ABCD
TE
CLV MON W
CLV MON V
CLV MON U
CLV CON W
CLV CON V
CLV CON U
CLV PWM
TR1
TF1
SLD PWM
FF1
FR1
ADIP
PEAK
BOTM
FE
ABCD
TE
RMC DTCK
XHOLD SW
SET KEY
XWK1
OPEN
XHOLD SW
BEEP
MUTE
XHP STB
BEEP
MUTE
XHP STB
VREF MON
S MON
PD_S0
PD_S1
SSB CLK
SSB DATA
OFTRK
XRF RST
XRST MTR DRV
XCS NY
XCS NY
CLV CON U
VC PWN
VL PWN
VLON
SLEEP
FFCLR
SET KEY
XWK1
OPEN
RMC KEY
FS4
PD_S0
PD_S1
S MON
OFTRK
XRF RST
SSB CLK
SSB DATA
VD PWM
SLD CON V
SLD CON W
SLD CON U
SLD MON U
SLD MON V
SLD MON W
SLD CON U
TE
REXT
WPP
C
D
D-C
IY
IX
JX
JY
A
A-C
B
TON-C
CIG
CDN
PD-NI
PD-I
PD-O
DVDD
ADIP
-IN
S-MON
FE
ABCD
AVCC
OFC-1
OFC-2
PS
LP
EQ
AGND
CCSL2
VC
VREF075
PEAK
BOTM
DGND
OFTRK
SCK
SBUS
AUTOMATIC
POWER CONTROL
ADFG
XRST
RF
LPF
VREF11
RF AMP,FOCUS/TRACKING
ERROR AMP
TRK-
TRK+
FCS-
FCS+
AGND
VREF
C
D
IY
IX
LD-A
LD-K
JX
JY
A
B
MON
AVCC
SO
SI
VCC
EEPROM
XBUSY
RST
GND
XCS
SK
DI
DO
DIGITAL SIGNAL PROCESSOR,
DIGITAL SERVO SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER,
ATRAC ENCODER/DECODER,
CSP(Chip Size Package)
D/A CONVERTER,16M BIT D-RAM
SYSTEM CONTROL
MCUVDD0
MIFVSS3
XRST
S MON
VB MON
CHG MON
SET KEY 1
SET KEY 2
HIDC MON
WK DET
REC KEY
AVDD
AVSS
VDIOSC
OSCI
OSCO
HALF LOCK SW
RMC KEY
VSIOSC
DAVDD
VREFL
AOUTL
AOUTR
VREFR
DAVSS
ASYO
ASYI
AVDI
BIAS
RFI
AVS1
PCO
PDO
FILI
FILO
CLTV
PEAK
BOTM
ABCD
FE
AUX1
VC
ADIO
ADRT
AVD2
AVS2
ADRB
SE
TE
DCHG
APC
DSPVDD0
DSPVSS0
XTSL
BEEP
XGUM ON
SO0
SI0
AOUT SEL
MIFVSS1
MIFVDD1
SET CODE3
SET CODE2
SET CODE1
SET CODE0
OPEN CLOSE SW
CLK SEL
NC
VC PWM
VL PWM
MCUVSS0
EVA
TEST0
TEST1
MIFFVSS0
MIFVDD0
MCUVDD2
SSB CLK
SSB DATA
JTAGVSS
JTAGVDD
TDO
TCK
TMS
TDI
TSB SLV0(TSL0)
TSB SLVI(TSLI)
TSB SLV VDD(TSLVDD)
RMC DTCK
TSB MST VDD(TSMVDD)
DRAMVSS1
DRAMVDD1
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
TEST2
MIFVSS2
MIFVDD3
XHP STBY
CHG
CHG GAIN
FFCLR
SLEEP
VLON
SLD MON
FLASHVSS
FLASHVDD
PROTECT
SYNC REC
XAVLS
CLV U MON(SPDL MON)
MCUVDD3
XRF RST
XRST MTR DRV
XCS NY
MUTE
CS RTC
XOPT CTL
MCUVSS1
TSB SLV CHK
LCD STB
XCS LCD
XPD ADA
XCS ADA
HD CON 2
HD CON 1
MODE1
MODE2
MODE3
MIFVDD2
PD SI
PD SO
XMIC DET
XJACK DET
OPT DET
XPATCH
LCD RST AUX
XMUTE
NC
DIN1
DOUT
PWMLP
PWMLN
ADDT
LRCK
XBCK
MVCI
PWMRP
DSPVDD1
ADFG
FOCNT
DIFVDD0
DIFVSS0
APCREF
LDDR
TRDR
TFDR
FFDR
FRDR
MCUVDD1
FGIN
FS4
SPFD/SPVS/PWM3
SPCU
SPCV
SPCW
SPDV/RTG1
SPDW/RTG2
DSPVDD2
DSPVSS1
SLDV
SLDW
SLCU
SLCV
SLCW
DIFVDD1
DIFVSS1
EFMO
MNT3
MNT2
MNT1
MNT0
SENSE
TX
RECP
DSPVDD3
NC
DRAMVDD0
NC
NC
NC
NC
NC
NC
SET KEY
XWK1
HOLD SW
GND
XHP STB
MUTE
BEEP
VIF
UNREG
R IN
L OUT
AGND
AGND
L IN
R OUT
SHORT:TEST MODE
OPEN:NORMAL MODE
(TEST)
VREF MON
SPRD/SPDU/RTG0
DRAMVSS0
XTRST
SCK0
XHOLD SW
*
NC
PAUSE KEY
MIC SENS
X TEST
ORPLEDGH
RECLEDGH
ORPLEDGL
LED O
OPRLEDRL
GND SW
VGCTL
JOG A
JOG B
TSB SSB CTL
NC
SCS1
SI1
NC
SCK1
78 DD CTL
NC
DADT
FS256
SRDR
SFDR
NC
LED RED PWM
VD PWM
LED GREEN PWM
NC
LED G
LED R
VC
LED O
OPEN/CLOSE
DVDD
VC
UNREG
LED DRIVE
Q801,83
AUDIO BOARD
CN802
MAIN BOARD
(2/2)