Sony PS3 CECH-ZED1E User manual

CECH-ZED1E
3D Display
Instruction Manual

WARNING
ˎTo avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
ˎThis equipment has been tested and found to comply with the limits set out in the EMC
Directive using a connection cable shorter than 3 meters.
ˎA molded plug complying with BS1363 is fitted to this equipment for your safety and
convenience. Should the fuse in the plug supplied need to be replaced, a 5AMP fuse approved
by ASTA or BSI to BS1362, (i.e., marked with or mark) must be used. If the plug supplied
with this equipment has a detachable fuse cover, be sure to attach the fuse cover after you
change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover,
please contact your nearest Sony service station.
ˎSome people may experience discomfort (such as eye strain, eye fatigue, or nausea) while
watching 3D video images or playing stereoscopic 3D games on 3D displays. If you experience
such discomfort you should immediately discontinue use of your display until the discomfort
subsides. Generally we recommend that you avoid prolonged use of your PlayStation®3 system
and take 15 minutes breaks during each hour of play. However, when playing stereoscopic 3D
games or watching 3D video, the length and frequency of necessary breaks may vary from
person to person – please take breaks that are long enough to allow any feelings of discomfort
to subside. If symptoms persist, consult your doctor. The vision of young children (especially
those under six years old) is still under development. Consult with your child’s doctor or
optometrist before allowing young children to watch 3D video images or play stereoscopic 3D
games. Adults should supervise young children to ensure they follow the recommendations
listed above.
Precautions
Before using this product, carefully read this manual and retain it for future reference. Read also
the instructions for the PlayStation®3 system.
Safety
ˎDo not use a power cord other than the supplied AC power cord. Do not modify the cord.
ˎDo not allow liquid or small particles to get into the product. If this happens, stop use and
disconnect it from the electrical outlet immediately.
ˎNever disassemble or modify the product.
ˎDo not expose the product to dust, smoke or steam.
ˎDo not expose the product to high temperatures, high humidity or direct sunlight.
ˎDo not touch the product with wet hands.
ˎUnplug the AC power cord from the electrical outlet before cleaning or when you do not
intend to use the system for an extended period of time.
ˎDo not connect the AC power cord to a voltage transformer or inverter. Connecting the AC
power cord to a voltage transformer for overseas travel or an inverter for use in an automobile
may cause heat to build up in the system and may cause burns or a malfunction.
ˎKeep this product out of the reach of small children. Small children may swallow small parts
ormay wrap the cables around themselves, which may inflict injury or cause an accident or
amalfunction.
Use and handling
ˎThe LCD screen is made of glass and may crack if subjected to excessive force.
ˎPixels that are not lit or are continuously lit may appear in certain locations on the LCD screen.
The appearance of such spots is a normal occurrence associated with LCD screens and is not a
sign of a system malfunction. LCD screens are made using highly precise technology. However,
a very small number of dark pixels or continuously lit pixels exist on each screen. Also, a
distorted image may remain on the screen for several seconds after the system has been
turnedoff.
ˎDirect exposure to sunlight may damage the system’s LCD screen. Be careful when using the
system outdoors or near a window.
ˎWhen using the system in a cold environment, you may notice shadows on the graphics or the
screen may appear darker than usual. This is not a malfunction, and the screen will return to
normal when the temperature goes up.
ˎDo not leave still images displayed on the screen for an extended period of time, as doing so
may cause a faint image to be left permanently on the screen.
ˎBe careful when carrying the product. If you do not have a good grip, the product may drop
causing potential damage or injury.
ˎDo not place the product on surfaces that are unstable, tilted or subject to vibration.
ˎDo not place any objects on top of the product. Do not stand on the product.
ˎDo not throw or drop the product, or otherwise expose it to strong physical impact.
ˎDo not allow the product to come into contact with liquids.
ˎFollow the instructions below to help prevent the product exterior from deteriorating or
becoming discoloured.
ˋWipe with a soft, dry cloth.
ˋDo not place any rubber or vinyl materials on the product exterior for an extended period
of time.
ˋDo not use solvents or other chemicals. Do not wipe with a chemically-treated cleaning cloth.

Checking the version of the PS3™ system software
To use the 3D display, the PS3™ system software must be version 3.70 or later. You
can check the system software version by selecting (Settings) (System
Settings) [System Information] on the XMB™(XrossMediaBar) menu of the
PS3™system.
Unpacking
ˎ 3D display (1) ˎ Stand (1) ˎ Neck (1)
ˎ AC power cord (1) ˎ HDMI cable (1) ˎ 3D glasses (2 sets) (pouch, USB cable)
ˎ Instruction manual (1)
Assembly
1 Insert the neck into the stand until you hear a click.
Check that the neck and stand face in the same direction, as shown in the
illustration.
2 Securely anchor the neck in place by tightening the mounting screw on the
bottom of the stand.
3 Insert the display into the neck until you hear a click.
Hints
ˎBe careful not to pinch your hands or fingers when you assemble
the stand anddisplay.
ˎYou can adjust the tilt angle of the display by up to 10° from the
vertical (Figure ). Hold the stand down with one hand and move
the upper part of the display with your other hand. Do not try to tilt
the display any further than 10° from the vertical, since this may
damage it.
ˎAt least two people must perform the steps for removing the display
from the neck and stand. One person must hold the neck and stand
securely on a flat surface and press the button on the hinge. At the
same time, another person can lift the display upwards.
Rear
Press to detach display from neck
andstand.
Using the 3D display
Front
Status indicator
Red: power off (standby mode)
Blue: starting up
Green: running
Orange: no input signal
3D sync transmitter
Infrared receiver
Infrared receiver for the remote control
(sold separately).


Rear
Power button
Turns the power on and off (standby).
Input selector button
Switches between input signals.
Volume + button/ volume – button
MENU button
Displays and hides the menu.
3D button
Press the 3D button to display video images in 3D.
AC IN connector
Service connector
Component video input connectors
Audio input jacks
HDMI™ input connectors
Headphone jack
3D glasses
Infrared receiver
Power button
Power on/off: press and hold for at least 2 seconds.
Switching players when using SimulView™:
with the power on, press and release quickly.
Power indicator
Flashes: 3D mode
Flashes two times repeatedly: SimulView™ mode (2P)
Flashes slowly: SimulView™ mode (1P)
Flashes quickly: low battery charge
USB connector
BATTERY switch
When you start using the 3D glasses, be sure
toput the battery switch in the On position.
Nose pad
You can adjust the nose pad to fit the shape of
your nose.
Hint
Be careful not to pinch yourself in the hinges of the 3D glasses.

Setting the video output on the PS3™ system
1 Go to (Settings) (Display Settings).
2 Select [Video Output Settings].
3 Select [HDMI].
4 Select [Auto].
5 Verify the settings, select [Yes] and then press the button.
6 Set the display size to 24 inches.
7 Verify the settings, select [Yes] and then press the button.
Hint
When using this setting, connect the PS3™ system to the 3D display directly using
anHDMI cable. If the display and the PS3™ system are connected via an AV
amplifier or other device, this setting may not work correctly.
Navigating the menu
Picture Backlight Adjusts the brightness of the backlight
Picture Mode [Standard]: Provides a standard natural
looking picture appropriate for home use
[Dynamic]: Provides a bright picture with
emphasis on sharpness and contrast
[Cinema]: Provides a picture optimized for
watching movies
[Custom]: Applies custom picture settings
Reset Current
Mode
Resets all picture settings to default values
Screen*Wide Mode [Normal]: Displays the picture in its
original size
[Full]: Displays the picture in full-screen
mode
[PSP™ Zoom]: Displays the picture from
aconnected PSP®(PlayStation®Portable)
system in full-screen mode
Overscan Select [ON] when visual noise or a black
frame can be seen around the edges of
thescreen
Sound Sound Mode [Standard]: Provides a well-balanced,
natural sound over the entire range
[Dynamic]: Provides a clear sound with
emphasis on high and low frequencies
[Cinema]: Provides a sound with a feeling
of you-are-there immediacy, just like being
in a movie theatre
[Custom]: Applies custom sound settings
Reset Current
Mode
Resets all sound settings to default values
Balance Adjusts the volume balance between the
left and right speakers
3D 3D Format Adjusts the settings to match the 3D
format of the content being played when
the 3D image is not displayed properly

Settings HDMI Control When you select [ON], the display and the
connected HDMI equipment will be
powered on and off simultaneously
Signal Information Displays the resolution and frequency
ofthe picture
Quick Start When you select [ON], the display will
start more quickly when it is turned on.
Note that this will increase power
consumption when the display is in
standby mode
Language Sets the language displayed on the
menuscreens
Restore Default
Settings
Resets all settings to default values
* The [Screen] menu can be adjusted only when component video signal is input to the 3D display.
Hint
You can operate the 3D display using the Blu-ray Disc™ Remote Control CECH-
ZRC1E (sold separately). When operating using the BD remote control, use the
TVbutton, the MENU button, the RETURN button, the ENTER button and the
directional buttons. For details on operation, see the instruction manual for the
BDremote control.
Using SimulView™ mode
SimulView™ allows two players to view different screen images while playing the
same game. To use this feature, the game must support SimulView™ and both players
need 3D glasses.
Hints
ˎIn some viewing environments and for some video content, the images may not be
completely separate and it may appear that two different images are overlapping.
ˎSimulView™ Mode displays two different images on screen. Please put on 3D
glasses before playing or watching in SimulView™ Mode.
Charging the 3D glasses
1 Open the USB connector cover. Connect a Type A - micro-B USB cable.
2 Connect the other end of the USB cable to a PS3™ system or other
supported device.
The power indicator lights up during charging and turns off when charging
iscomplete.
Hints
ˎIf you start charging the 3D glasses while they are turned on, the power will
turnoff.
ˎThe 3D glasses cannot be charged when the battery switch is in the Off position.
Troubleshooting
The power to the display shuts off suddenly or has shut off unexpectedly.
CThe power goes off automatically when there is no incoming signal.
There are bright spots or dark spots on the screen.
CBlack (dark) pixels and continuously lit pixels may appear in certain locations on
the LCD screen. The appearance of such spots is a normal occurrence associated
with LCD screens and is not a sign of a system malfunction.
3D or SimulView™ images are not displayed, or the image does not look like
a3D or SimulView™ image.
CCheck that the 3D glasses are turned on.
CCheck that the 3D glasses are charged.
CThe 3D glasses operate by receiving a constant infrared signal from the 3D sync
transmitter. The glasses may not operate properly in the following cases.
ˋThe 3D glasses do not face the 3D sync transmitter.
ˋThere are objects blocking the path between the 3D glasses and the 3D sync
transmitter.
ˋThere are other infrared communication devices, lighting fixtures, space
heaters, or similar equipment nearby.
CUse the 3D glasses so that they are level with the display. If you are lying down or
if your head is tilted, it may be difficult to experience the 3D effect and the
colour of the image may change.
CIf the display and the PS3™ system are connected via an AV amplifier or other
device, 3D or SimulView™ images may not be displayed correctly. Connect the
PS3™ system to the display directly using an HDMI cable, and then adjust the
video output settings on the PS3™ system.
The 3D glasses are not receiving any power.
CCheck that the battery switch is in the On position.

Specifications
3D display
Inputs and Outputs HDMI input connectors × 2
Component video input connectors
(Y/CB (PB)/CR (PR)) × 1 each
Audio input connectors × 2: 2 ch, pin jack
USB connector × 1: Type A, for service use only
Headphone output connector × 1: stereo mini jack
Speakers Stereo 2 ch (full range, 3 W × 2, 28 mm × 28 mm, elliptical)
Subwoofer (5 W, 50 mm)
Load impedance: 8 Ω
Panel resolution 1920 × 1080
Effective screen size 23.5 inches
Power requirement AC 100 V – 240 V (50/60 Hz)
Power consumption 60 W, 0.6 A – 0.26 A (in use),
0.2 W or less (in standby mode),
7 W or less (when the Quick Start feature is [ON])
Operating temperature 5°C – 35°C
Dimensions (w × h × d) Approx. 650 × 391 × 207 mm (including stand)
Weight Approx. 5.7 kg (including stand)
3D glasses
Battery type Built-in, rechargeable lithium-ion battery
Battery voltage DC 3.7 V
Battery capacity 70 mAh
Power consumption 5 V 100 mA
Dimensions (w × h × d) Approx. 174 × 41 × 177 mm (in use),
approx. 174 × 41 × 60 mm (folded)
Weight Approx. 47 g
Design and specifications are subject to change without notice.
GUARANTEE
This product is covered for 12 months from date of purchase by the manufacturer’s warranty set
out in the PS3™ system manual.
Please refer to the PS3™ system manual for full details.
The manufacturer of this product is Sony Computer Entertainment Inc., 1-7-1 Konan,
Minato-ku, Tokyo 108-0075 Japan.
The Authorised Representative for EMC and product safety in Europe is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
Distributed in Europe by Sony Computer Entertainment Europe Ltd, 10 Great Marlborough
Street, London, W1F 7LP, United Kingdom.
This product may fall within the scope of national export control legislation. You must comply
fully with the requirements of such legislation and of all other applicable laws of any jurisdiction
in relation to this product.
Where you see either symbol on any of our electrical products, batteries or packaging, it
indicates that the relevant electrical product or battery should not be disposed of as general
household waste in Europe. To ensure the correct waste treatment of the product and battery,
please dispose of them in accordance with any applicable local laws or requirements for disposal
of electrical equipment/batteries. In so doing, you will help to conserve natural resources and
improve standards of environmental protection in treatment and disposal of electrical waste.
This symbol may be used on batteries in combination with additional chemical symbols. The
chemical symbols for mercury (Hg) or lead (Pb) will appear if the battery contains more than
0.0005% mercury or more than 0.004% lead.
This product contains a battery which is permanently built-in for safety, performance or data
integrity reasons. The battery should not need to be replaced during the lifetime of the product
and should only be removed by skilled service personnel. To ensure the correct waste treatment
of the battery, please dispose of this product as electrical waste.

" ", "PlayStation", " " and "PSP" are registered trademarks of Sony Computer Entertainment Inc.
"SimulView" is a trademark of Sony Computer Entertainment Inc.
"XMB" and "xross media bar" are trademarks of Sony Corporation and Sony Computer Entertainment Inc.
"SONY" and " " are registered trademarks of Sony Corporation.
"Blu-ray Disc™" and "Blu-ray™" are trademarks of the Blu-ray Disc Association.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.
eu.playstation.com
© 2011 Sony Computer Entertainment Inc. All rights reserved.