Sony SDM-V72W User manual

1-796-576-23 (1)
© 2002 Sony Corporation
TFT LCD Color
Computer Display
Operating Instructions
Mode d’emploi
Manual de instrucciones
US
FR
ES
SDM-V72W

- 1 -
Ow ner’s Record
The model and serial numbers are located at the rear of
the unit. Record these numbers in the spaces provided
below. Refer to them whenever you call upon your dealer
regarding this product.
Model No. ______________________________
Serial No. ________________________________
FCC Notice
Thisequipment hasbeen tested and found to comply with
the limitsfor a ClassBdigital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user isencouraged to try to correct the interference by
one or more of the following measures:
■Reorient or relocate the receiving antenna.
■Increase the separation between the equipment and
receiver.
■Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
■Consult the dealer or an experienced radio/TV
technician for help.
You are cautioned that any changesor modifications
not expressly approved in thismanual could void your
authority to operate this equipment.
For questions regarding your product or for the Sony
Customer Information Service Center nearest you call:
1-800-222-SONY (7669)
The number below is for FCC related matters only.
As an ENERGY STAR Partner,
Sony has determined that this
product or product models meets
the ENERGY STAR guidelines
for energy efficiency.
®
®
ENERGY STAR is a U.S. registered mark.
®
W ARNING
To prevent fire or shock hazard, do not expose
the unit to rain or m oisture.
Dangerously high voltages are present inside
the unit. Do not open the cabinet. Refer
servicing to qualified personnel only.
Declaration of Conformity
Trade Name: SONY
Model No.: SDM-V72W
Responsible Party: Sony Electronics Inc.
Address: 680 Kinderkamack Road,
Oradell, NJ07649 USA
Telephone No.: 201-930-6972
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
NOTICE
This notice is applicable for USA/Canada only.
If shipped to USA/Canada, install only a UL
LISTED/CSA LABELLED power supply cord
meeting the following specifications:
SPECIFICATIONS
Plug Type Nema-Plug 5-15p
Cord Type SVT or SJT unshielded,
minimum 3 x 18 AWG
Length Maximum 15 feet
Rating Minimum 7 A, 125 V
NOTICE
Cette notice s’applique aux États-Unis et au
Canada uniquement.
Si cet appareil est exporté aux États-Unis ou
au Canada, utiliser le cordon d’alimentation
portant la mention UL LISTED/CSA LABELLED
et remplissant les conditions suivantes :
SPÉCIFICATIONS
Type de fiche Fiche Nema 5-15 broches
Cordon Type SVT ou SJT, non blindé,
minimum 3 x 18 AWG
Longueur Maximum de 15 pieds
Tension Minimum 7 A, 125 V
Downloaded from: https://www.usersmanualguide.com/

- 2 -
Table of Contents
Precautions - - - - - - - - - - - - - - - - - - - - - - - - - -3
Identifying partsand controls - - - - - - - - - - - - - - - - -5
Setup - - - - - - - - - - - - - - - - - - - - - 8
Setup 1: Activating and replacing a battery for remote card -9
Setup 2: Connecting your display to your computer - - - - - - 10
Setup 3: Connecting the audio cord - - - - - - - - - - - - - 11
Setup 4: Connecting video cables - - - - - - - - - - - - - - 12
Setup 5: Connecting the ACadapter- - - - - - - - - - - - - 13
Setup 6: Organizing the cablesand replacing the back panel 14
Setup 7: Connecting the power cord- - - - - - - - - - - - - 15
Setup 8: Turning on the display, computer, or other equipment 16
Setup 9: Adjusting the tilt - - - - - - - - - - - - - - - - - - 17
Using the Remote Card - - - - - - - - - - 18
Customizing Your Display - - - - - - - - - 19
Navigating through PCmenus- - - - - - - - - - - - - - - - 19
PCPICTURECONTROL options- - - - - - - - - - - - - - - - 20
PCAUDIO CONTROL options- - - - - - - - - - - - - - - - - 21
PCSCREEN CONTROL options - - - - - - - - - - - - - - - - 22
PCSETUPoptions - - - - - - - - - - - - - - - - - - - - - - 24
Navigating through Video menus- - - - - - - - - - - - - - 25
PICTURECONTROLoptions(for Video, S-Video, or Component) 26
AUDIO CONTROLoptions(for Video, S-Video, or Component) 27
SCREEN CONTROL options(for Video, S-Video, or Component) 28
SETUPoptions(for Video, S-Video or Component) - - - - - - 31
Technical Features - - - - - - - - - - - - - 32
Power save function- - - - - - - - - - - - - - - - - - - - - 32
Preset and user modes - - - - - - - - - - - - - - - - - - - 32
Controlling the volume - - - - - - - - - - - - - - - - - - - 33
Using the headphones - - - - - - - - - - - - - - - - - - - 33
Troubleshooting - - - - - - - - - - - - - - 34
PCon-screen messages - - - - - - - - - - - - - - - - - - - 34
Self-diagnosisfunction - - - - - - - - - - - - - - - - - - - 39
Specifications - - - - - - - - - - - - - - - 40
Appendix A - - - - - - - - - - - - - - - - 41
Appendix B- - - - - - - - - - - - - - - - - 42
■Macintosh isa trademark
licensed to Apple Computer,
Inc., registered in the U.S.A.
and other countries.
■Windows®isregistered
trademark of Microsoft
Corporation in the United
Statesand other countries.
■IBM PC/AT and VGA are
registered trademarksof IBM
Corporation of the U.S.A.
■VESA and DDCTM are
trademarksof the Video
ElectronicsStandards
Association.
■ENERGY STAR isa U.S.
registered mark.
■All other product names
mentioned herein may be
the trademarksor registered
trademarksof their
respective companies.
■isa trademark of
SRSLabs, Inc. SRSWOW
technology isincorporated
under license from SRSLabs,
Inc.
■Furthermore, “ TM” and “ ®”
are not mentioned in each
case in thismanual.
Downloaded from: https://www.usersmanualguide.com/

- 3 -
Precautions
Warning on pow er connections
Use the supplied power cord. If you use a
different power cord, be sure that it is
compatible with your local power supply.
If you do not use the appropriate cord, this
display will not conform to mandatory FCC
standards.
The equipment should be installed near an
easily accessible outlet.
Installation
Do not install or leave the display:
■In placessubject to extreme temperatures, for
example near a radiator, heating vent, or in
direct sunlight. Subjecting the display to high
temperatures, such asin an automobile
parked in direct sunlight, could cause
deformationsof the casing or malfunctions.
■In placeswhere the display may tip and fall,
such aslocationssubject to any vibration or
shock or an unstable surface.
■Near any equipment that generatesa strong
magnetic field, such asa TV or variousother
household appliances.
■In placessubject to inordinate amountsof
dust, dirt, or sand, for example near an open
window or an outdoor exit. If setting up
temporarily in an outdoor environment, be
sure to take adequate precautionsagainst
airborne dust and dirt. Otherwise irreparable
malfunctionscould occur.
■In placeswhere the display may come in
contact with extreme moisture or liquid, such
asin bathroom or area near pool. Avoid
placing glassesor cupson top of the display
that may cause liquid to spill inside.
Handling the LCD screen
■Do not leave the LCD screen facing the sun as
it can damage the LCD screen. Take care when
you place the display by a window.
■Do not push on or scratch the LCD screen. Do
not place a heavy object on the LCD screen.
Thismay cause the screen to lose uniformity or
cause LCD panel malfunctions.
■If the display isused in a cold place, a residual
image may appear on the screen. Thisisnot a
malfunction. The screen returnsto normal as
the temperature risesto a normal operating
level.
■If a still picture isdisplayed for a long time, a
residual image may appear for a while. The
residual image will eventually disappear.
■The LCD panel becomeswarm during
operation. Thisisnot a malfunction.
for 100 to 120 V AC for 200 to 240 V AC
For use only with AC adapter, Sony AC-DP001
Downloaded from: https://www.usersmanualguide.com/

- 4 -
About the built-in stereo speakers
Be sure to keep magnetic recording equipment,
tapes, and floppy discsaway from the speaker’s
opening as the speakers generate a magnetic
field. Thismagnetic field may affect data stored
on magnetic tapes and discs.
Handling the headphones
Be sure to remove the headphones before
moving away from the display. If the
headphone cord ispulled away from the display
abruptly, injury or damage may occur.
Note on the LCD (Liquid Crystal
Display)
Please note that the LCD screen is made with
high-precision technology. However, black
points or bright points of light (red, blue, or
green) may appear constantly on the LCD
screen, and irregular colored stripes or
brightness may appear on the LCD screen. This
is not a malfunction.
(Effective dots: more than 99.99%)
Maintenance
■Be sure to unplug the power cord from the
power outlet before cleaning your display.
■Clean the LCD screen with a soft cloth. If you
use a glasscleaning liquid, do not use any type
of cleaner containing an anti-static solution or
similar additive asthismay scratch the LCD
screen’scoating.
■Clean the cabinet, panel, and controlsfirst
with a soft cloth lightly moistened with a mild
detergent solution, then dry off with a soft
cloth. Do not use any type of abrasive pad,
scouring powder, or solvent, such asalcohol or
benzine.
■Do not rub, touch, or tap the surface of the
screen with sharp or abrasive itemssuch asa
ballpoint pen or screwdriver. Thistype of
contact may result in a scratched LCD display
screen.
■Note that material deterioration or LCD screen
coating degradation may occur if the display is
exposed to volatile solventssuch asinsecticide,
or if prolonged contact ismaintained with
rubber or vinyl materials.
Tr a n sp o r t a t i o n
■Disconnect all cablesfrom the display and
grasp the support and base sectionsof the
display stand firmly with both handswhen
transporting. If you drop the display, you may
be injured or the display may be damaged.
■The back panel isdesigned to come off; do not
lift the display by itsback panel alone.
■When you transport thisdisplay for repair or
shipment, use the original carton and packing
materials.
Disposal of the display
■Do not dispose of thisdisplay with general
household waste.
■The LCD containsa small amount of liquid
crystal and mercury. The fluorescent tube used
in thisdisplay also containsmercury. Follow
your local ordinancesand regulationsfor
disposal.
Downloaded from: https://www.usersmanualguide.com/

- 5 -
Identifying parts and controls
See the pages in parentheses for further details. 1 Pow er button (page 16)
This button turns the display on. To turn the
display off, press this button again.
2 Pow er LED indicator (page 16)
This LED indicates power ON/OFF, power
save, and remote off status.
3 M ENU button (pages 19 and 25)
This button turns the menu screen on and
off.
4 +/- buttons (pages 19, 25, and 33)
These buttons are used to select the menu
items and make adjustments, and also to
control the volume when the menu screen is
not active.
5 OK button (pages 19 and 25)
Thisbutton activatesthe selected menu item
and enables adjustments using the +/-
buttons 4.
6 WIDE button (pages 22 and 29)
This button switches between different
screen size modesin both PC and Video
modes.
7 INPUT button (pages 19 and 25)
This button switches between connected
input sources, including PC input,
Composite video input, S-Video input, and
Y/Pb/Pr Component video input.
8 Stereo speakers (page 33)
These output the audio signals.
9 Headphones jack (page 33)
This jack outputs audio signals to the
headphones.
q; Remote card IR (Infrared Receiver) sensor
w indow
Thiswindow detectssignalsfrom the remote
card.
POWER
OK
WIDE
MENU
INPUT
3
1
4
5
6
7
Front of the LCD display
8
2
9
q;
POWER
DK
WIDE
MENU
INPUT
Side view of the LCD display
Downloaded from: https://www.usersmanualguide.com/

- 6 -
Identifying parts and controls - cont.
qa Back panel (pages 10 and 14)
Remove this panel to access power and
input connections for the display.
qs HD15 input for PC Input (analog RGB)
This connector inputs analog RGB video
signals (0.700 Vp-p, positive) and SYNC
signals.
qd Audio input jack for PC Input (page 11)
This jack inputs audio signals when
connected to the audio output jack of a
computer or other audio equipment.
qf Composite Input (page 12)
These jacks input audio/video signals when
connected to the composite output jack of
video equipment.
qg S-Video Input (page 12)
This jack inputs video signals when
connected to the S-Video output jack of
video equipment for better picture quality
than the composite video. You will need to
connect audio cables for sound (S-Video
carries only the video signal).
qh Y/Pb/Pr Component Video and Audio
Input (page 12)
These jacks input high quality video and
audio signalswhen connected to equipment
with component output.
qj DC IN connector (page 13)
This connector provides 16.5V DC power to
the display. Connect the AC adapter
(provided) to this connector.
qk Cable cover (pages 10 and 14)
Remove this cover to organize the cables
connected to the display monitor.
Rear of the LCD display
qa
PCIN VIDEO IN
AUDIO IN
DCIN 16.5V
SVIDEOVIDEORLPBRLHD15 PR
Y
qs qd qf qg qh qj
qk
Downloaded from: https://www.usersmanualguide.com/

- 7 -
Identifying parts and controls - cont.
ql M UTE button (page 33)
Press this button to mute the sound. Press
again or + Volume button to restore the
sound.
w; PICTURE M ODE button (page 26)
Pressthisbutton to switch between different
picture mode settings.
wa WIDE M ODE button (pages 22 and 29)
Pressthisbutton to switch between different
screen size modesin both PC and Video
modes.
ws POWER button (page 16)
Pressthisbutton to turn the display on when
the power LED indicator is red. To turn the
display off (remote off mode), press this
button again. For remote off, see page 18.
wd PC input button (page 12)
Press this button to display PC input signal.
wf VIDEO input button (page 12)
Pressthisbutton to display either Composite
video or S-Video signal.
wg Y/Pb/Pr Component Video button
(page 12)
Press this button to display Y/Pb/Pr
Component Video input signal.
wh M ENU button (pages 19 and 25)
Pressthisbutton to turn the menu screen on
and off.
wj Arrow buttons (pages 19 and 25)
Use these buttons to select the menu items
and make adjustments.
wk OK button (pages 19 and 25)
Press this button to activate the selected
menu item and adjustmentsusing the arrow
buttons wj.
wl +/- VOLUM E buttons (pages 19, 25 and 33)
Press these buttons to control the volume.
ql w; wa ws
wd
wf
wg
wk
wj
wh
wl
Remote Card
Downloaded from: https://www.usersmanualguide.com/

- 8 -
Setup
Before using your display, check that the following items are included in your carton:
■LCD display
■Remote card
■ACPower cord
■ACAdapter (AC-DP001)
■HD15/D-sub video signal cable (analog RGB)
■Audio cord (stereo miniplug)
■Composite video extension cable
■S-Video extension cable
■Warranty card
■Quick Setup Guide
■Thisinstruction manual on CD-ROM
zThis display can be wall mounted
with VESA Standard Wall Mount. For
instruction and mounting bracket
please refer to your local retailer.
✍
AC Power Cord
Audio cord
CD
Quick Setup Guide
Display
AC Adapter
HD15/D-sub video signal cable Composite video extension cable S-Video Extension Cable
Printed in USA
4-062-412-13(T1)
LIM IT ED WA RRA NTY
Sony Electron ics Inc. and Son y of Canada Lt d. (“SON Y”) w arrants t his Produ ct against def ects in
material or w orkman ship as follo ws:
1.LABOR: For a per iod o f thr ee (3) years fr om th e date of pu rchase, if t his Prod uct is d eterm ined
to be defecti ve, Sony w ill repair o r replace the Produ ct with a new o r rebuilt u nit, at no charge, or
pay the labo r charges to an y Sony autho rized service facil ity. After t he Warran ty Period , you m ust
pay for all labo r charges.
2.PARTS: In addi tion, Son y wil l suppl y, at no charge, new o r rebuilt r eplacements i n exchang e
for defectiv ep arts for a p eriod of t hree (3) years. Aft er the warrant y period, you m ust pay for all
parts cost.
Toob tain war ranty serv ice, you mu st take the Prod uct, or del iver the Pro duct freig ht prepai d, in
either its ori ginal p ackaging or p ackaging af fordi ng an equal deg ree of prot ection ,t o any autho rized
Sony Service facility.
Thiswar ranty does no t cover custom er instruct ion, install ation, set up adju stments or si gnal receptio n
problem s.
Thisw arran ty do es not co ver any uni ts wh ich hav e been pr eviou sly alt ered, rep aired o r servi ced by
anyone oth er than a servi ce facili ty aut hori zed by Son y, or a un it on wh ich th e factor y-appli ed serial
number h as been alter ed or rem oved. Thi s warran ty does n ot cover cosm etic dam age or d amage
due to acts of God , accident, m isuse, abu se, neglig ence, comm ercial u se, or mo dificat ion of , or to
any part o f the Product . This warra nty does no t cover dam age due to im proper o peration o r
maintenan ce, connecti on to i mpro per vol tage supp ly. This w arranty d oes not co ver pro ducts sol d
ASIS o r WITH ALL FAULTS.
This warrant y is valid onl y in the United St ates and Canada and on ly in t he respectiv e country o f
purchase.
Proof of purch asei n the form of a bi ll of sale or recei pted invo ice, which i sev idence that t he unit is
within th e Warrant y period, m ust be p resented to ob tain warr anty service.
This warran ty is in valid i f the fact ory appli ed serial num ber has been altered o r removed f rom the
Product.
REPAIRORREPLACEMENT AS PROVIDED UNDER THIS WARRAN TY IS THE EXCLUSIVE REMEDY
OFTHE CONSUMER. SONY SHALL N OT BELIA BLEFOR ANY IN CIDENTALOR CONSEQUENTIAL
DAMAGES FORBREACH OF ANY EXPRESSOR IM PLIEDWARRANTY ON THIS PRODUCT. EXCEPT
TO THE EX TENT PROHIB ITED BY APPLI CABLE LAW, A NY IMPLIED WA RRANTY OF
MERCHANTABILITYOR FITNESS FORA PARTICULAR PURPOSEON THIS PRODUCT IS LIMITED IN
DURATIONTO THE DURATION OF THIS WARRANTY.
Some states and pr ovinces d o not al low t he exclusio n or li mitat ion of in cidental or co nsequenti al
damages, or al low li mitat ions on h ow lo ng an im plied w arranty l asts, so the abo ve limi tation s or
exclusions m ay not app ly to y ou. This w arrant y gives y ou specif ic legal ri ghts, and y ou may h ave
other rig hts wh ich vary fr om stat e to state o r prov ince to p rovin ce.
FORFREQUENTL
YCALLED TELEPHONENUM BERS,PLEASE SEEREVERSE SIDE.
Computer Disp lay Products
P
Warranty Card
Downloaded from: https://www.usersmanualguide.com/

- 9 -
Activating and replacing a battery for remote card
Activating the remote card
To activate the battery for the remote card,
remove the plastic slip by pulling the tab.
Replacing the remote card battery
1To replace the worn battery with a new
one, remove the battery compartment
from the remote card by pressing the
lock latch to the right, then pull out the
compartment.
2Be sure that the positive terminal (+) of
the CR2025 lithium battery isfacing
upward.
3Close the battery compartment to with a
gentle push until you hear the click.
The worn battery should be disposed
properly. Check with your local regulations.
Setup 1
12
zHandle the remote card with care. Do
not try to bend it, drop it or get it wet. Avoid
placing it near a heater, in direct sunlight, or
where humidity is high.
✍
Caution: Keep the batteries away from the
reach of young children. Batteries may pose
a potential health hazard if put in their
mouth (i.e., they may swallow it or choke on
it).
Downloaded from: https://www.usersmanualguide.com/

- 10 -
Connecting your display to your computer
Turn off the display and computer before connecting. Do not touch the pins of the video signal cable connector as this might bend the pins.
1Remove the back panel by holding top
with one hand asin the illustration then
snap out the buttonslocated at each
corner.
2Remove the cable cover by lightly pulling
top concave portion.
■Connecting to an IBM PC/AT or compatible
computer
Using the HD15/D-sub cable (supplied),
connect the computer to the display’s HD15
input connector.
Be sure to check the alignment of the HD15/
D-sub cable. Do not force the connector in
the wrong way or the pins might bend.
■Connecting a Macintosh
When connecting a Macintosh computer,
use an adapter (not supplied) if necessary.
Connect the adapter to the computer before
connecting the video signal cable.
Setup 2
12
Connecting a M acintoshConnecting to an IBM PC/AT
Downloaded from: https://www.usersmanualguide.com/

- 11 -
Connecting the audio cord
Connect the supplied audio cord to the display’s
PC audio input jack. The audio cord connector
and the audio input jack are color coded. Match
like colors to connect.
Using the display’s speakers or headphones, you
can listen to sound from your computer or other
audio equipment connected to the display’s
audio input jacks.
For more information, see “ Controlling the
volume” on page 33.
Setup 3
Downloaded from: https://www.usersmanualguide.com/

- 12 -
Connecting video cables
You can connect composite video cables, S-Video cable, and also Y/Pb/Pr Component Video cables for your video needs.
Setup 4
EO IN PBRLPR
Y
VIDEORL
VIDE
SVIDEO
■Connecting with composite video cables
Composite video sends combined signal of color shade
(chrominance) and brightness (luminance) through a
single cable. For thisconnection use the traditional A/V
cable. (Combined audio L/Rand video cable)
■Connecting with S-Video cables
If your equipment has an S-Video output, use this
connection for better picture quality than the
composite video connection. You will need to connect
audio cables (audio L/R) for the sound (S-Video carries
only the video signal).
■Connecting with Y/Pb/Pr Component Video cables
If your equipment has a Y/Pb/Pr Component Video
output, use this connection for the highest quality
color picture. Y/Pb/Pr Component Video sends signals
of two color shades (chrominance) and brightness
(luminance) separately. Y/Pb/Pr Component Video
cablesare usually marked with Y, Pb and Pr. In addition
to the Y/Pb/Pr Component Video, you will also need to
connect an audio L/Rcable for sound.
Downloaded from: https://www.usersmanualguide.com/

- 13 -
Connecting the AC adapter
Connect the AC adapter (supplied) to the display.
Setup 5
DCIN 16.5V
AC adapter
(supplied)
Downloaded from: https://www.usersmanualguide.com/

- 14 -
Organizing the cables and replacing the back panel
1Bundle the cablesand cords; then route
through the base stand.
2Replace the cable cover by aligning the
cylindrical pegsto the holes, then press.
3Hold the back panel with one hand and
pressthe panel at the corners.
Setup 6
3
1
2
Downloaded from: https://www.usersmanualguide.com/

- 15 -
Connecting the pow er cord
1First, connect the ACadapter to the
display asshown in Setup 5 (see
page 13).
2Connect the power cord to the AC
adapter (supplied).
3Connect the power cord to the nearest
power outlet.
Setup 7
DCIN 16.5V
To pow er outlet
Pow er cord
(supplied)
AC adapter
(supplied)
12
3
Downloaded from: https://www.usersmanualguide.com/

- 16 -
Turning on the display, computer, or other equipment
1Pressthe POWERbutton on the right
side of the display.
The power LED indicator lights up in green.
2Turn on the computer or your video
source equipment.
Press the INPUT button on the right side of
the display repeatedly to select the desired
input signal. Or with your remote card select
and press the desired input signal.
Pressing the POWER button on the
remote card w hile the pow er LED
indicator is green will turn the pow er
LED to red. A red pow er LED indicates
the display is in remote off.
For more information, see INPUT button on
page 5 and Remote card on page 18.
If no picture appears on your screen
See Trouble symptoms and remedies on pages
34-38.
Setup 8
POWER
The remote card POWER button
will only turn your display on from
remote off mode, indicated by red
pow er LED indicator. When the
display is in pow er OFF mode,
indicated by unlit pow er LED, the
POWER button on the right side of
the display must be used to power
ON, indicated by green power LED
indicator.
✍
zThe POWER button on the side
of the display must initially be
pressed (to have unlit LED turned on)
to operate with the remote card.
✍
The display complies with the “ DDC” Plug
& Play standard and automatically detects
all the display’s information. No specific
driver needsto be installed to the computer
to operate.
The first time you turn on your computer
after connecting the display, the setup
Wizard may appear on the screen. In this
case, follow the on-screen instructions. The
Plug & Play display is automatically selected
so that you can use this display.
Note: Not all video graphic cards will
support 1280 x 768 wide aspect resolution.
Use with some devices may require
updated drivers. Please consult your video
graphic manufacturer for updated drivers.
Downloaded from: https://www.usersmanualguide.com/

- 17 -
Adjusting the tilt
The display will tilt 3 degrees forward and 15 degrees backward.
To use the display comfortably
Adjust the viewing angle of your display
according to the height of your desk and chair,
and so that light is not reflected from the screen
to your eyes.
Grasp the lower middle part of the LCD panel
while holding the display stand, then tilt the LCD
panel adequately backward.
Setup 9
WheWWhen adjusting the screen tilt, proceed
slowly and carefully, being sure not to hit the
display against the desk or the base of the
display stand.
✍
3° 15°
Downloaded from: https://www.usersmanualguide.com/

- 18 -
Using the Remote Card
Here is a closer look at the remote card. ql Press to mute the sound.
w; Press the PICTUREMODEbutton to select
one of the following Picture Modesfor video
and Y/Pb/Pr component video:
■Vivid
■Standard
■Movie
■Game
■Pro
wa Press the WIDEMODEbutton to switch
between different screen size modes:
ws Press the POWERbutton to turn on your
display from remote off mode or to switch to
remote off. See Note.
wd Press the PC button to receive PC input
signal.
wf Pressthe VIDEO button to receive composite
or S-Video signal.
wg Press the Y/Pb/Pr button to receive
Y/Pb/Pr component A/V signal.
wh Press the MENU button to display the main
menu of each input:
wj Press the V v B b buttons for Menu
navigation.
wk Press the OK button to confirm your
selection.
wl Press the Volume +/- buttons to adjust the
audio volume for all inputs.
The remote card POWER button
will only turn your display on from
remote off mode, indicated by red
pow er LED indicator. When the
display is in pow er OFF mode,
indicated by unlit pow er LED, the
POWER button on the right side of
the display must be used to pow er
ON, indicated by green power LED
indicator.
ql w; wa ws
wd
wf
wg
wk
wj
wh
wl
✍
PC menu ■Normal
■Full
Video menu ■Wide Zoom
■Zoom
■Letterbox
■Full
■Normal
PC main menu
displays ■PICTURECONTROL
■AUDIO CONTROL
■SCREEN CONTROL
■SETUP
Video
(or S-Video)
main menu
displays
■PICTURECONTROL
■AUDIO CONTROL
■SCREEN CONTROL
■SETUP
Downloaded from: https://www.usersmanualguide.com/

- 19 -
Customizing Your Display
You can make numerous adjustments to your
display using the on-screen menu. You can select
your menu and adjustments using the buttons
on the side of the display or by using your
remote card.
Navigating through PC menus
1Select the PCinput.
Press the INPUT button on the right side of
the display until you find the PC input you
want to select and press the OK button or
press the PC button on your remote card.
2Display the main menu.
Press the MENU button to display the main
menu on your screen and then press the OK
button.
3Select the menu you want to adjust.
Press the +/- buttons to display the desired
menu. Press the OK button to select the
menu item.
4Adjust the menu.
Pressthe +/- buttonsto make the adjustment,
and then press the OK button. When you
press the OK button, the setting is stored,
then the display returnsto the previousmenu.
5Close the menu.
Press the MENU button once to return to
normal viewing. If no buttonsare pressed, the
menu closes automatically after about 45
seconds.
INPUT
M ENU
,
OK
,
OK
Button layouts are different on the remote card.
M ENU
✍
Before making adjustments
Connect the display and the
computer, and turn them on. Wait for
at least 30 minutes before making
adjustments for the best results.
Downloaded from: https://www.usersmanualguide.com/