Sony SU-PT2M User manual

© 2004 Sony Corporation
SU-PT2M 4-099-468-12 (1)
4-099-468-12 (1)
Tabletop Stand
Instructions
SU-PT2M
GB
CS
CT
KR
AR

SU-PT2M 4-099-468-12 (1)
2(GB)
Thank you for purchasing this product.
To Customers
Sufficient expertise is required for installing this product. Be sure to subcontract the installation to Sony dealers
or contractors and pay special attention to safety during the installation. Sony is not liable for any damages or
injury caused by mishandling or improper installation.
WARNING
If the safety precautions are not observed or the product is used incorrectly, it may result in serious injury or fire.
This instruction manual shows the correct handling of the product and important precautions necessary to prevent
accidents. Be sure to read this manual thoroughly and use the product correctly. Keep this manual available for
future reference.
For Sony dealers
Sufficient expertise is required for installing this product. Be sure to read this instruction manual thoroughly to do
the installation work safely. Sony is not liable for any damages or injury caused by mishandling or improper
installation. Please give this manual to the customer after installation.
On Safety
Products by Sony are designed with safety in mind.
If the products are used incorrectly, however, it may result in a serious injury through fire, electric shock, the
product toppling over, or the product dropping. Be sure to observe the precautions for safety to prevent such
accidents.
CAUTION
This Tabletop Stand is intended for use only with the following products. Use with other apparatus is capable of
resulting in instability causing possible injury.
Specified product (As of June 2004)
Plasma TV KE-MX37A1 KE-MX37S1 KE-MX37N1 KE-MX37K1
KE-MX42A1 KE-MX42S1 KE-MX42N1 KE-MX42K1 KE-MX42M1

SU-PT2M 4-099-468-12 (1)
English
GB
3(GB)
For Customers
WARNING
If the following precautions are not observed, serious injury or death through fire, electric shock, the
product toppling over, or the product dropping can result.
Be sure to subcontract the installation to Sony dealers.
If persons other than Sony dealers do the installation work, this may result in serious injury, as the TV is very
heavy.
Be sure to take measures to prevent the stand from toppling over.
If you fail to do so, the Tabletop Stand may topple over and cause injury or property damage.
Anchor the TV to the wall, pillar, etc. to prevent it from toppling over.
Be sure to install the Tabletop Stand on a solid and flat surface.
Do not install the Tabletop Stand so that it leans in one direction. If you do so, the
Tabletop Stand may topple over or the TV may fall. This may cause injury or
property damage.
Be sure to install the Tabletop Stand on a stable surface.
If you install the Tabletop Stand on an unstable surface, it may lose its balance and
topple over or fall off. This may cause injury or property damage.
Do not lean on or hang from the TV with the TV installed on the Tabletop
Stand.
The Tabletop Stand may topple over, or the TV may fall and cause serious injury or
death.
Do not cover the ventilation hole of the TV.
If you cover the ventilation hole (with a cloth, etc.), heat may build up inside and
cause fire.

SU-PT2M 4-099-468-12 (1)
4(GB)
Do not allow the mains lead or the connecting cable to be pinched.
•Do not allow the mains lead or the connecting cable to be pinched when you
install the TV on the Tabletop Stand. If the mains lead or the connecting cable is
damaged, this may result in a fire or an electric shock.
•Do not step on the mains lead or the connecting cable when you carry the
Tabletop Stand. The mains lead or the connecting cable may be damaged, and
this may result in a fire or an electric shock.
Be sure to carry the stand in the manner shown in this manual.
If the Tabletop Stand is carried incorrectly, it may topple over and cause injury.
Do not stumble over the mains lead or the connecting cable.
If you stumble over the mains lead or the connecting cable, the Tabletop Stand may topple over and cause injury.
CAUTION
If the following precautions are not observed, injury or property damage may occur.
Do not install any equipment other than the specified product.
This stand is designed for use with the specified product only. If you install equipment other than specified, it may
fall and cause injury or property damage.
Be sure to secure the TV.
Secure the TV to the Tabletop Stand using the supplied screws.
If the TV is not installed securely, it may fall and cause injury.
Notes on installation
Install the stand on a solid and flat surface. Do not allow the stand to be installed at an angle or incline. To avoid
this, observe the following precautions.
– If you install the stand on a soft surface such as a mat or a carpet, lay a board over the designated location
beforehand.
– Do not install the stand in a place subject to direct sunlight or near a heater.
–Do not install the stand in a hot or humid place, or outdoors.
Note on use
To keep the stand clean, occasionally wipe the stand with a dry soft cloth. Stubborn stains may be removed with a
cloth slightly dampened with diluted detergent. Then wipe the area with a dry soft cloth. Do not use chemicals,
such as thinner or benzine, as they damage the finish of the stand.

SU-PT2M 4-099-468-12 (1)
5(GB)
WARNING
To Sony Dealers
The following instructions are for Sony Dealers only. Be sure to read safety precautions described above
thoroughly and pay special attention to safety during the installation, maintenance, checking and repair of this
product.
Be sure that two or more persons do the installation work.
Be sure that two or more persons install the TV on the Tabletop Stand. If one person does the installation work
alone, this may result in an accident or an injury.
Be sure to install the TV securely, following the instructions in this manual.
Be sure to tighten the screws firmly.
If the TV is not installed securely, it may fall and cause injury.
Be careful not to hurt your hands or fingers during installation.
Be careful not to hurt your hands or fingers when installing the TV.
Check the parts
Name Quantity Name Quantity
Bottom plate Cable tie
1
Securing screw
14
Anchor attachment
2
Prepare a Phillips screwdriver, that fits the screws indicated above, beforehand.

SU-PT2M 4-099-468-12 (1)
6(GB)
Install the TV
WARNING
If you allow the mains lead to be pinched under or between pieces of equipment, this may result in a short
circuit or an electric shock. If you stumble over the mains lead or the connecting cable, the stand may topple
over and cause injury.
Decide on the installation location and lay the stand down before installing the TV.
Since the TV is heavy, it is recommended that you decide on the installation location beforehand and lay the
Tabletop Stand down there before installing the TV.
Note
Do not push or pull the Tabletop Stand while it is on the floor. The rubber footings on the base of the stand may
come off.
1Attach the Tabletop Stand to the TV.
1Place the TV, with its screen facing down, on a stable, cloth-covered work surface, at least 20 cm off the
floor.
2Insert the dowels of the Tabletop Stand in the slots of the TV.
2Secure the TV and the Tabletop Stand with the supplied screws.
Note
When using an electric screwdriver, set the torque setting to about 1.5N·m.
1
2
At least
20 cm
Rear side of the TV
Soft rag
Bottom of the TV
Slots
Securing screw

SU-PT2M 4-099-468-12 (1)
7(GB)
3Connect the mains lead and the connecting cable to the TV.
Tip
See the instruction manual of Plasma TV (KE-MX37A1, KE-MX37S1, KE-MX37N1, KE-MX37K1, KE-
MX42A1, KE-MX42S1, KE-MX42N1, KE-MX42K1, KE-MX42M1) for more details on connecting the mains
lead and the connecting cable.
4Bundle the mains lead and the connecting cable with the supplied cable
tie.
Mains lead and connecting cables

SU-PT2M 4-099-468-12 (1)
8(GB)
Safety measures to prevent toppling over
WARNING
Be sure to take measures to prevent the stand from toppling over.
If you fail to do so, the TV may topple over and cause injury. Anchor the TV to a wall, pillar, etc., to prevent it
from toppling over.
Prepare a commercially available rope or chain and wall anchor bracket beforehand.
1Remove the screws attached to the TV, and replace them with the supplied anchor attachments.
2Secure the wall anchor bracket to a solid wall or pillar.
3Pass the rope or chain through both holes of the anchor attachments and then tighten the other end of the
rope or chain to the wall anchor bracket.
132
Wall anchor
bracket

SU-PT2M 4-099-468-12 (1)
9(GB)
Specifications
Design and specifications are subject to change without notice.
Dimensions: (mm) A 584
B 286
C 410
D 125
E 181
Weight: (kg) 6
A
C
DE
B

SU-PT2M 4-099-468-12 (1)
10 (GB)

SU-PT2M 4-099-468-12 (1)
等离子电视接收机用 桌面支架
Instructions
SU-PT2M
GB
CS
CT
KR
AR

SU-PT2M 4-099-468-12 (1)
2(CS)
感谢您购买本产品。
致用户
安装本产品需要足够的专业技术。必须请合格的安装人员进行安装，安装期间应特别注意安全。Ｓｏｎｙ 对误操作
或不正确安装造成的任何损坏或受伤不承担责任。
警告
如果不遵守安全事项或未能正确使用本产品，则可能导致严重受伤或者火灾。
本说明书介绍了正确使用本产品和防止事故发生而必需的重要事项。必须通读本手册并正确使用本产品。请妥善保管
本手册，以备将来参考。
致 Ｓｏｎｙ 经销商及安装人员
安装本产品需要足够的专业技术。必须通读本说明书以安全安装。Ｓｏｎｙ 对误操作或不正确安装造成的任何损坏或受
伤不承担责任。请在安装后将本手册交给用户。
安全事项
Ｓｏｎｙ 的产品设计非常注重安全。
但是，如果使用不正确，则可能因火灾、电击、产品倾倒或产品跌落而导致严重受伤。必须遵守安全事项以防止此类
事故的发生。
当心
此桌面支架仅设计用于以下产品。若用于其它电器，支架可能不稳并导致可能的受伤。
指定产品（２００４ 年 ６ 月止）
等离子电视接收机用 ＫＥ－ＭＸ３７Ａ１ ＫＥ－ＭＸ３７Ｓ１ ＫＥ－ＭＸ３７Ｎ１ ＫＥ－ＭＸ３７Ｋ１
ＫＥ－ＭＸ４２Ａ１ ＫＥ－ＭＸ４２Ｓ１ ＫＥ－ＭＸ４２Ｎ１ ＫＥ－ＭＸ４２Ｋ１ ＫＥ－ＭＸ４２Ｍ１

SU-PT2M 4-099-468-12 (1)
3(CS)
中文（简）
CS
致用户
警告
如果不遵守下列事项，则可能因火灾、电击、产品倾倒或产品跌落导致严重受伤或死亡。
必须由合格的安装人员进行安装。
由于电视机很重，操作不当，则可能导致严重受伤。
必须采取措施防止支架倾倒。
否则，桌面支架可能倾倒并导致受伤或财产损失。
将电视机固定在墙壁、支柱上，防止其倾倒。
必须将桌面支架安装在坚固平坦的表面。
切勿向一个方向倾斜安装桌面支架。否则，桌面支架可能倾倒或电视机可能跌落。
这样可能导致受伤或财产损失。
必须将桌面支架安装在稳定的表面。
如果您将桌面支架安装在不稳定的表面，则支架可能失去平衡并倾倒或跌落。这样
可能导致受伤或财产损失。
切勿倚靠或攀爬装在桌面支架上的电视机。
桌面支架可能倾倒或电视机可能跌落，并导致严重受伤或死亡。
切勿遮盖电视机通风孔。
如果您遮盖通风孔（用布等），则热量会在电视机内部聚积并引起火灾。

SU-PT2M 4-099-468-12 (1)
4(CS)
切勿使电源线或连接电缆受压。
•在桌面支架上安装电视机时，切勿使电源线或连接电缆受压。如果电源线或连接
电缆损坏，则可能导致火灾或电击。
•当您搬运桌面支架时，切勿踩踏电源线或连接电缆。电源线或连接电缆可能损
坏，并可能导致火灾或电击。
必须按照本手册中介绍的方法搬运支架。
如果桌面支架被不正确搬运，则支架可能倾倒并导致受伤。
切勿绊到电源线或连接电缆。
如果您绊到电源线或连接电缆，则桌面支架可能倾倒并导致受伤。
当心
如果不遵守下列事项，则可能导致受伤或财产损失。
切勿安装除指定产品以外的任何设备。
本支架仅设计用于指定产品。如果您安装除指定产品以外的设备，则设备可能跌落并导致受伤或财产损失。
必须固定电视机。
用附带的螺丝将电视机固定到桌面支架上。
如果电视机未被牢固安装，则可能跌落并导致受伤。
安装时的注意事项
将支架安装在坚固平坦的表面。切勿将支架以某个角度安装或倾斜安装。为避免此类事情发生，请遵守下列事项。
–如果将支架安装到垫子或地毯等柔软的表面，请预先在指定的位置上放一块木板。
–切勿将支架安装在阳光直射的地方或加热器附近。
–切勿将支架安装在炎热或潮湿的地方，或户外。
使用时的注意事项
若要保持支架清洁，请经常用干的软布擦拭支架。顽固污渍可用蘸有稀释清洁剂的布轻轻擦去。然后用干的软布擦拭
此区域。切勿使用稀释剂或汽油等化学剂，因为它们会损坏支架的表层。

SU-PT2M 4-099-468-12 (1)
5(CS)
警告
致安装人员
下列说明仅致 Ｓｏｎｙ 经销商。必须通读上述安全事项，并特别注意本产品的安装、维护、检查和维修过程中的安
全。
必须由两个或更多人进行安装。
必须由两个或更多人将电视机安装到桌面支架。如果一个人单独安装，则可能导致事故或受伤。
必须按照本手册中的说明牢固安装电视机。
必须拧紧螺丝。
如果电视机未牢固安装，则可能跌落并导致受伤。
安装过程中，请小心不要伤到手或手指。
安装电视机时，请小心不要伤到手或手指。
检查部件
名称 数量 名称 数量
底盘 电缆扎带
１
安全螺丝
１４
固定螺丝
２
请预先准备一把适合以上指定螺丝的十字型螺丝起子。

SU-PT2M 4-099-468-12 (1)
6(CS)
安装电视机
警告
如果电源线压在设备部件下或部件之间，则可能导致短路或电击。如果您绊到电源线或连接电缆，则支架可能倾
倒并导致受伤。
安装电视机之前，决定安装位置并放置支架。
由于电视机很重，建议您预先决定安装位置，并在安装电视机之前放置桌面支架。
注意
桌面支架在地板上时，切勿推或拉桌面支架。支架底部的橡胶底脚可能脱落。
1将桌面支架安装到电视机上。
1将电视机屏幕朝下放置在稳定的、垫有布的表面，离地板至少 ２０ ｃｍ。
2将桌面支架上的销插入电视机的槽。
2用附带的螺丝将电视机和桌面支架固定。
注意
使用电钻时，将扭矩设定至约 １．５Ｎ·ｍ 。
1
2
至少
２０ ｃｍ
电视机后侧
软布
电视机底部
槽
安全螺丝

SU-PT2M 4-099-468-12 (1)
7(CS)
3将电源线和连接电缆连接到电视机。
提示
关于连接电源线和连接电缆的更多详情，请参阅等离子电视接收机用（ＫＥ－ＭＸ３７Ａ１，ＫＥ－ＭＸ３７Ｓ１，ＫＥ－ＭＸ３７Ｎ１，
ＫＥ－ＭＸ３７Ｋ１，ＫＥ－ＭＸ４２Ａ１，ＫＥ－ＭＸ４２Ｓ１，ＫＥ－ＭＸ４２Ｎ１，ＫＥ－ＭＸ４２Ｋ１，ＫＥ－ＭＸ４２Ｍ１）的使用说明书。
4用附带的电缆扎带捆扎电源线和连接电缆。
电源线和连接电缆

SU-PT2M 4-099-468-12 (1)
8(CS)
防倾倒安全措施
警告
必须采取措施防止支架倾倒。
否则，电视机可能倾倒并导致受伤。将电视机固定在墙壁、支柱上，防止其倾倒。
请预先准备一个市售绳索或链条和墙壁挂钩。
1拧下装在电视机上的螺丝，然后换上附带的固定螺丝。
2将墙壁挂钩固定到坚固的墙壁或支柱上。
3将绳索或链条穿过固定螺丝上的孔，然后将至墙壁挂钩的绳索或链条的另一端拉紧。
132
墙壁挂钩

SU-PT2M 4-099-468-12 (1)
9(CS)
规格
设计和规格若有变更，恕不另行通知。
尺寸：（ｍｍ） Ａ ５８４
Ｂ ２８６
Ｃ ４１０
Ｄ １２５
Ｅ １８１
重量：（ｋｇ） ６
A
C
DE
B

SU-PT2M 4-099-468-12 (1)
2(CT)
感謝您購買本產品。
致用戶
安裝本產品需要足夠的專業技術。必須請 Sony 經銷商或承包人進行安裝，安裝期間應特別注意安全。Sony 對
誤操作或不正確安裝造成的任何損壞或引致受傷不承擔責任。
警告
如果不遵守安全事項或未能正確使用本產品，則可能導致嚴重引致受傷或者火災。
本說明書介紹了正確使用本產品和防止事故發生而必需的重要事項。必須通讀本手冊並正確使用本產品。請妥善保管
本手冊，以備將來參考。
致 Sony 經銷商
安裝本產品需要足夠的專業技術。必須通讀本說明書以安全安裝。Sony 對誤操作或不正確安裝造成的任何損壞或引
致受傷不承擔責任。請在安裝後將本手冊交給用戶。
安全事項
Sony 的產品設計非常注重安全。
但是，如果使用不正確，則可能因火災、電擊、產品傾倒或產品墮下而導致嚴重引致受傷。必須遵守安全事項以防止
此類事故的發生。
小心
此桌面支架∕坐檯架僅設計用於以下產品。若用於其它電器，支架∕檯架可能不穩並導致可能的引致受傷。
指定產品（截至 2004 年 6 月）
等離子電視電漿電視 KE-MX37A1 KE-MX37S1 KE-MX37N1 KE-MX37K1
KE-MX42A1 KE-MX42S1 KE-MX42N1 KE-MX42K1 KE-MX42M1