Sony DMBK-R3012 User manual

SPEAKER STAND
DMBK-R3012
INSTALLATION MANUAL
1st Edition

!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
DieAnleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt dieAngaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.

1 (E)
DMBK-R3012
1. Overview
The SPEAKER STAND DMBK-R3012 is the monitor speaker stand used in the OXF-R3 system. The
DMBK-R3012 is placed on the rear of the CONTROL PANEL OXF-CP3048.
2. Specifications
Mass : 31 kg (when assembled)
Dimensions :
50 (movable)
503
400
300
24
1075
1045.5
576
576
646
2400 (Speaker shelf)
3667
646 DMBK-R3012
DMBK-R3011 DMBK-R3011
DMBK-R3012
movable
1285
1. Overview
2. Specifications
Unit : mm
OXF-CP3048 with DMBK-R3011/R3012

2 (E) DMBK-R3012
Structure of DMBK-R3012
Speaker shelf : 1
Bracket (1) : 2
Bracket (2) : 2
Bracket : 2
Support bar : 2
Support : 2
Screw (B5 x10) : 22
Screw (B5 x16) : 4 (for fixing bracket (1))
Nut (N5) : 4
3. Installation Procedure
Notes on installation
.Be sure to install the DMBK-R3012 with two or more persons for safety.
.Be sure to turn off the main power of the CONTROL PANEL OXF-CP3048 before starting installation.
Required tools
Phillips type (+) screwdriver
Nut driver (across: 5 mm)
Procedure
(1) Insert the two support bars into the pipes of the two supports as shown, and fix them tentatively with
screws (B5 x10) 1respectively.
Insert the support bar into the pipe of the support as far as it can go.
(2) Place the two supports to which the support bars have already been attached, on the rear of the
CONTROL PANEL OXF-CP3048.
(Place the support bars 50 cm apart from the rear panel of the CONTROL PANEL OXF-CP3048.)
(3) Perform the following works on the respective support bars (supports).
1) Attach the bracket (2) to a support bar as shown and fix them tentatively with the one screw
(B5 x10) 2.
2) Pinch the beam of the CONTROL PANEL OXF-CP3048 with the bracket (1) and fix it to the
beam tentatively with the two screws (B5 x16) 3.
3) Attach the bracket (1) to the bracket (2) tentatively with the two screws (B5 x10) 4.
4) Loosen the two fixing screw 2of the bracket (2), and adjust height of the bracket (1) so that the
bracket (2) has the same height as the beam. Tighten the two fixing screws 2after adjustment.
5) Loosen the two screws (B5 x10) 4and adjust position of the supports (support bars). Tighten
the 4 screws 4after adjustment.
(4) Attach the two brackets to the speaker shelf with twelve screws (B5 x10) 5. (Use the six screws for
each bracket.)
(5) Attach the speaker shelf to the two support bars. Attach the speaker shelf by inserting the respective
support bars into pipes of the brackets respectively. Fix them tentatively with the screw (B5 x10)
6respectively.
(6) Tighten all screws that have been tentatively fixed.
2. Specifications
3. Installation Procedure

3 (E)
DMBK-R3012
Bracket
Bracket
Speaker shelf
2
2
1
4
4
4
1
3
3
Support
Supprot
Support
Support bar
Support
bar
Support bar
Bracket
Speaker shelf
5
6
6
Bracket (1)
Bracket 
(1) Bracket 
(2)
Bracket (2)
Bracket 
(1)
Beam
Beam
N5
50 mm
3. Installation Procedure

The material contained in this manual consists of
information that is the property of Sony Corporation and
is intended solely for use by the purchasers of the
equipment described in this manual.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation et
sont destinées exclusivement à l’usage des acquéreurs
de l’équipement décrit dans ce manuel.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind,
und ausschließlich zum Gebrauch durch den Käufer der
in dieser Anleitung beschriebenen Ausrüstung bestimmt
sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.

Printed in Japan
Sony Corporation 1998. 2 16
Broadcasting & Professional Systems Company ©1998
Published by Global Support Promotion Dept.
DMBK-R3012 (WW) J, E
3-200-364-01