Sony Ipela SNCA-ZX104 User manual

4-412-914-11 (2)
Hybrid Camera Receiver
SNCA-ZX104
Installation Manual
Before operating the unit, please read this manual thoroughly and retain it for
future reference.
© 2012 Sony Corporation Printed in China
Owner’s Record
The model and serial numbers are located on the bottom of the unit. Record these
numbers in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this
product.
Model No. Serial No.
WARNING
To reduce the risk of fire or electric shock, do not
expose this apparatus to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
WARNING
This installation should be made by a qualified service person and should conform to
all local codes.
WARNING
This unit has no power switch.
When installing the unit, incorporate a readily accessible disconnect device in the
fixed wiring, or connect the power plug to an easily accessible socket-outlet near the
unit.
If a fault should occur during operation of the unit, operate the disconnect device to
switch the power supply off, or disconnect the power plug.
WARNING
Using this unit at a voltage other than 120 V may require the use of a different line
cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in this
manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to comply
with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
For the customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Pour les clients au Canada
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo,
Japan.
The Authorized Representative for EMC and product safety is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.
For any service or guarantee matters please refer to the addresses given in separate
service or guarantee documents.
This apparatus shall not be used in the residential area.
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause radio
interference in which case the user may be required to take adequate measures.
In the case that interference should occur, consult your nearest authorized Sony
service facility.
When installing the installation space must be secured in consideration of the
ventilation and service operation.
Do not block the ventilation slots at the left side and right side panels, and vents of
the fans.
Leave a space around the unit for ventilation.
Leave more than 15 cm (6 in) of space in the rear of the unit to secure the operation
area.
When the unit is installed on the desk or the like, leave at least 2 cm (13/16 in) of space in
the left and right sides.
Leaving 40 cm (15 3/4in) or more of space above the unit is recommended for service
operation.
WARNING
THIS WARNING IS APPLICABLE FOR USA ONLY.
If used in USA, use the UL LISTED power cord specified below.
DO NOT USE ANY OTHER POWER CORD.
Plug Cap Parallel blade (NEMA 1-15P Configuration)
Cord Type NISPT-2 or SPT-2, two 16 or 18 AWG wires
Length Minimum 1.5 m (4 ft 11 in), Less than 4.5 m (14 ft 9 in)
Rating Minimum 7 A, 125 V
Using this unit at a voltage other than 120 V may require the use of a different line
cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer
servicing to qualified service personnel.
WARNING
THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES.
1. Use the approved Power Cord (2-core mains lead) / Appliance Connector / Plug that
conforms to the safety regulations of each country if applicable.
2. Use the Power Cord (2-core mains lead) / Appliance Connector / Plug conforming to
the proper ratings (Voltage, Ampere).
If you have questions on the use of the above Power Cord / Appliance Connector /
Plug, please consult a qualified service personnel.
IMPORTANT
The nameplate is located on the bottom.
ATTENTION
The electromagnetic fields at the specific frequencies may influence the picture of this
unit.
Notes on Use
Before Use
If you find condensation when you open the package, turn on the power after leaving
the unit off for about 60 minutes.
Data and security
Access to the SNCA-ZX104 is protected only by a user name and your set password.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU OR
ANYONE ELSE, FOR THE INTERRUPTION, DISCONTINUATION OR CANCELLATION OF
SERVICE(S) RELATED TO THIS RECEIVER. THE SERVICE IS PROVIDED AS-IS, AND SONY
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT
TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR
THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Always verify that the unit is operating properly before use. SONY WILL NOT BE
LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR
PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY OTHER
REASON WHATSOEVER.
If you lose data by using this unit, Sony accepts no responsibility for restoration of
the data.
Operating or storage location
Avoid operating or storing the unit in the following locations.
Extremely hot or cold places (Operating temperature: 0 °C to 45 °C [32 °F to
113 °F])
Exposed to direct sunlight for a long time, or close to heating equipment (e.g., near
heaters)
Close to sources of strong magnetism
Close to sources of powerful electromagnetic radiation, such as radios or TV
transmitters
Locations subject to strong vibration or shock
Ventilation
To prevent heat buildup, do not block air circulation around the unit.
Transportation
Always turn off the power when carrying.
When transporting the unit, repack it as originally packed at the factory or in
materials of equal quality.
Cleaning
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn stains
can be removed using a soft cloth dampened with a small quantity of detergent
solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may
damage the surface finishes.
Please consult the store of purchase or authorized Sony dealer if there were troubles
and anomalies.
Getting Started
This Installation Manual explains how to operate an IPELA HYBRID-compatible hybrid
camera receiver.
Features
SNCA-ZX104 is IPELA HYBRID-compatible hybrid camera receiver.
The IPELA HYBRID-compatible camera connected to this unit’s SLOC port connects
to an external network via this unit’s LAN port. Also, composite video signals from a
camera are output via this unit’s video output terminal.
Up to 4 IPELA HYBRID-compatible cameras can be connected to this receiver.
An IPELA HYBRID-compatible camera’s pan, tilt and zoom, etc., functions can be
controlled from a keyboard connected to this unit.
The Serial PTZ function converts control signals input from the RS-485 port to TCP/
IP packets and sends them via a network. Connect a keyboard compatible with the
Pelco-D protocol to the RS-485 port.
You can control up to 255 Serial PTZ-compatible cameras registered to a single
SNCA-ZX104.
Note
The Multicast function of the IPELA HYBRID-compatible camera cannot be used when
it is connected to the unit. Instead, use the Unicast function.
About the Supplied Manuals
Installation Manual (this document)
This Installation Manual describes the names and functions of parts and controls of
the receiver, gives connection examples and explains how to set up the unit. Be sure
to read the Installation Manual before operating.
User’s Guide (stored in the CD-ROM)
The User’s Guide describes how to set up the receiver and how to control the unit via a
Web browser.
After installing and connecting the receiver correctly, operate by referring to this
User’s Guide.
Using the CD-ROM Manuals
The manual can be read on a computer with Adobe Reader installed.
You can download Adobe Reader free from the Adobe website.
1 Open the index.htm file in the CD-ROM.
2 Select and click on the manual that you want to read.
Note
If you have lost or damaged the CD-ROM, you can purchase a new one from your Sony
dealer or Sony service counter.

A
B
C
Network cable
(straight,
not supplied) AC adaptor
10BASE-T/
100BASE-TX
Hub
Network
To power
socket
To an analog monitor
IPELA HYBRID-compatible
camera
Coaxial cable
Coaxial cable
To a keyboard
I/O port
connector
D
Unit: mm (inches)
250 (9 7/8)
210 (8 3/8)
44
(1 3/4)
Location and Function of Parts
Front 

POWER indicator (green)
When the receiver receives power, an internal system check is performed.
The indicator lights up when the unit is operating normally.

NETWORK indicator (green/orange)
The indicator lights up or flashes when the unit is connected to the network. The
indicator remains off when the unit is not connected to the network.
When connecting the unit via 100BASE-TX, the indicator lights up in green. When
connecting the unit via 10BASE-T, the indicator lights up in orange.

SLOC indicator (orange)
The indicator lights up in orange when an SLOC connection to a hybrid camera is
established.
The indicator flashes in orange when an SLOC transmission error is occurring.
Rear 

Video output terminal (BNC)
Outputs composite video signals.

DC IN 12 V DC (power input) terminal
Connect to the supplied DC 12 V AC adapter.

SLOC (IP coaxial transfer) port
Use this terminal to connect the unit to an IPELA HYBRID-compatible camera via a
coaxial cable.

Reset switch
To restore the unit’s default settings, press this switch using a pointed object and turn
the power on while the switch is pressed.

RS-485 selection switch
Set this switch to ON to enable network functions; this unit’s settings can then be
changed over the network that is connected via the LAN port. This unit’s Serial PTZ
functions are also enabled; the unit can accept input from the keyboard connected to
this unit’s I/O port.
Set this switch to OFF to disable network functions and block input from the I/O port.
After switching, it is necessary to turn the power off and on again, to enable the
setting.

I/O (input/output) port
This unit includes an RS-485 port. You can connect a keyboard that is compatible with
Pelco-D protocol control signals in order to control the unit.
Indication Function
NC
+ RS-485 (+) input/output (GND level reference)
– RS-485 (–) input/output (GND level reference)
G RS-485 reference GND

LAN (network) port (RJ-45)
Connect to a 10BASE-T or 100BASE-TX network using a network cable.
CAUTION
For safety, do not connect the connector for peripheral device wiring that might
have excessive voltage to this port. Follow the instructions for this port.
When you connect the LAN cable of the unit to peripheral device, use a
shieldedtype cable to prevent malfunction due to radiation noise.
Connection
Connecting to the Network
Connect to the network router or hub via this unit’s LAN port, using a network cable
(not supplied).
Connecting to a Monitor
Connect a video output terminal of the unit to an analog monitor using a coaxial cable
(not supplied).
Connecting to an IPELA HYBRID-compatible Camera
Connect a SLOC port of the unit to an IPELA HYBRID-compatible camera’s SLOC port
using a coaxial cable (not supplied).
The maximum coaxial cable length is RG-59 300 m.
Note
The high-frequency characteristics of coaxial cables may differ, even if the cables are of
the same classification. Use a high-quality, high-frequency coaxial cable with this unit.
For details on coaxial cables and cameras that can be connected to this unit, refer to the
instruction manual of the connecting SLOC device. For further details, please consult an
authorized Sony dealer.
Connecting to a Keyboard
Using the supplied I/O port connector, connect a keyboard (not supplied) that
supports the Pelco-D protocol, and set the RS-485 selection switch to ON.
The RS-485 selection switch is set to OFF in the factory default settings.
Set the RS-485 selection switch of only SNCA-ZX104 units with a keyboard connected
to ON.
For details on settings related to the Serial PTZ function and settings related to connecting
the keyboard, refer to the User’s Guide.
For details on camera settings related to Serial PTZ, refer to the camera’s Instruction
Manual.
Connecting the Power Source
Connect to the supplied DC 12 V AC adapter.
Specifications
Interface
SLOC input BNC ×4, 75Ω termination
Analog video output BNC ×4, composite 1.0 Vp-p, 75Ω termination
Network port 10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O port Camera control interface: ×1 (RS-485)
Others
Power supply DC 12V
Consumption current 0.8 A
Operating temperature 0 °C to 45 °C (32 °F to 113 °F)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Operating humidity 20% to 80% (no condensation)
Storage humidity 20% to 80% (no condensation)
Dimensions 210 × 44 × 250 mm (8 3/8× 1 3/4× 9 7/8in) (w/h/d)
(without the projecting parts)
Mass Approximately 1.1 kg
Supplied accessories CD-ROM (User’s Guide and supplied programs) (1)
Installation Manual (this document) (1)
B&P Warranty Booklet (1)
AC adaptor (AC-NB12A) (1)
I/O port connector (1)
Note
This package may contain additional installation
manuals and/or documentation.
AC adaptor (AC-NB12A)
Power supply AC 100 to 240 V, 50/60 Hz
0.65 A to 0.35 A
Output DC 12 V, 2.5 A
Operating temperature 0 °C to 45 °C (32 °F to 113 °F)
Operating humidity 20% to 80% (no condensation)
Storage temperature –20 °C to +60 °C (–4 °F to +140 °F)
Storage humidity 20% to 80% (no condensation)
Dimensions 49.5 × 28 × 99.5 mm (2 × 1 1/8× 4 in) (w/h/d) (without
the projecting parts)
Mass Approximately 0.2 kg (7 oz)
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it inspected
periodically for safe use.
It may appear flawless, but the components may have deteriorated over time, which
may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
NOTICE TO USERS
© 2012 Sony Corporation. All rights reserved. This Installation Manual, in whole or in
part, may not be reproduced, translated or reduced to any machine readable form
without prior written approval from Sony Corporation.
SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL,
THE UNIT OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE UNIT OR SUCH OTHER
INFORMATION. IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS
MANUAL, THE UNIT OR OTHER INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.
Sony Corporation reserves the right to make any modification to this manual or the
information contained herein at any time without notice.
“IPELA”, and are trademarks of
Sony Corporation.
Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
sloc™ is a trademark owned by the Intersil Corporation family of companies.
All other company and product names are trademarks or registered trademarks of
the respective companies or their respective makers.