Sony Trinitron KV-H29TF User manual

Trinitron Color TV
#############
1997 by Sony Corporation

KV-H29TF
3-860-682-11 (1)

2
20 mm
3.8 mm

3
21
AUTO
PROGR
TV SYS: D/K
AUTO PROGRAM
VHF LOW
PR: 01
1
AUTO
PROGR
– MENU+ ENTER
3
L
(MONO)R

4

Getting Started -EN
5
WARNING Table of contents
• Dangerously high voltages are present inside the TV.
• Operate the TV only at 110-240 V AC.
• Do not open the cabinet and the rear cover of the TV.
Refer servicing to qualified personnel.
• To prevent fire or shock hazard, do not expose the TV
to rain or moisture.
• Do not operate the TV if any liquid or solid object
falls into it. Have it checked immediately by qualified
personnel only.
• Do not block the ventilation openings.
• Do not install the appliance in a confined space, such
as a bookcase or built-in cabinet.
• Do not install the TV in hot, humid or excessively
dusty places.
• Do not install the TV where it may be exposed to
mechanical vibrations.
• Do not keep the TV plugged in if you are not going to
use it for several days.
• Do not pull the power cord to disconnect the TV. Pull
it out by the plug.
• Use only the supplied screws (as shown on page 2) to
fasten the TV to the TV stand or to stabilize the TV
against a wall or a pillar. Use of other screws may
damage the TV.
Note on the remote commander
• The supplied remote commander is used on several models of
the TV. If you do not find instructions for some controls that
are on the remote commander, that means your TV does not
employ the features of those controls, e.g. .
Notes
• When you turn on the TV, you may hear the “boon” sound
that is caused by the demagnetization of the TV. This does not
indicate a malfunction.
• The picture color may become abnormal if you change the
direction of your TV. To obtain the normal picture color, press
Uon the TV to turn off the TV for five minutes and then turn it
on again.
Getting Started
6Connections
8Introducing the menus
9Changing the menu language
10 Presetting channels
Operations
12 Watching the TV
14 Adjusting the picture and sound
16 Listening to the woofer sound (3D WOOFER)
17 Listening to the surround sound (SURROUND)
18 Customizing the TV
Additional Information
19 Troubleshooting
Back cover Specifications
All contents are subject to change without notice.
Design and specificafions are subject to change without
notice.
EN

Getting Started
6-EN
Connecting the 3D WOOFER
1Attach the 3D WOOFER into the footholds on the top of the TV.
2Connect the wires to the 3D WOOFER (8Ω) terminals at the rear of the TV.
The red wire should be connected to the ‘red terminal and the black wire to the ’black terminal.
Notes
• Connect only the supplied 3D WOOFER; otherwise the TV may malfunction.
• Unplug the TV from the wall outlet when connecting the 3D WOOFER.
• Make sure that none of the 3D WOOFER wire strands stick out, making contact with the neighbouring speaker terminal, to prevent a
malfunction caused by a short circuit of the terminals.
Connecting a VHF antenna or a combination VHF/UHF antenna
— 75-ohm coaxial cable (round)
Attach an optional IEC antenna connector to the 75-ohm coaxial cable.
Plug the connector into the (antenna) socket at the rear of the TV.
Connections
Getting Started
Red wire
Black wire
12
3D WOOFER
Rear of TVRear of TV
or
On a wall

Getting Started -EN
7
Connecting optional equipment
You can connect optional audio/video equipment to your TV such as a VCR, multi disc player, camcorder, video
game, or stereo system.
Connecting video equipment using video input jacks
or
(yellow)
-L (white)
-R (red)
to video and
audio inputs
: Signal flow
VCR
to
antenna
output
to
antenna
socket
Rear of TV
to audio
inputs
When connecting a monaural VCR
Connect the yellow plug to (VIDEO) and the black plug to (AUDIO)-L (MONO).
When connecting a VCR to the (antenna) terminal
Preset the signal output from the VCR to the program position 0.
If both S Video and video signals are input simultaneously
The S Video input signal is selected. To view a video input signal, disconnect the (S Video) connection.
Note on the video input
When no signal is input, the screen becomes blue.
Connecting audio/video equipment using Ú(MONITOR/TV OUT) jacks
Rear of TV
to
antenna
socket
(yellow)
-L (white)
-R (red) : Signal flow
VCR
to
antenna
output
to video and
audio outputs
to S video output
to video and
audio outputs
21
L
R
(MONO)
…
Ú
Front of TV
3
L
(MONO)R
Camcorder
: Signal flow
2
1
L
R
(MONO)
Audio system

Getting Started
8-EN
Introducing the
menus
A/V CONTROL
You can preset TV channels, adjust the picture and sound qualities, and select some settings using the on-screen
menus. You can use the buttons on both the remote commander and the TV to operate the menus.
Notes (except for AUTO PROGRAM)
• When a menu is selected after pressing ENTER, the color of
both the menu and the menu symbol change and the cursor
(z) appears beside the first item of the menu.
• When an item on the menu is selected after pressing ENTER,
the color of the item changes.
• You can refer to the guide ( ) at the bottom of the
menus (except for the A/V CONTROL and PRESET menus)
for the basic operations of the menu.
• If more than approximately 60 seconds elapse after you press a
button, the menu screen disappears automatically.
PRESET
BASS 80
00
80
TREBLE
BALANCE
AUDIO ADJUST
3D WOOFER : ON
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
T I LT CORRECT:
0
PRESET
SKIP: PR02 OFF
TV SYS: D/K
COL SYS : AUTO
ENGL I SH
AUTO PROGRAM
MANUAL PROGRAM
LANGUAGE/ :
PICTURE
40
100
0
80
V I DEO ADJUST
COLOR
BRI GHT
HUE
SHARP
VM: HIGH
45
0
FEATURES
Getting back to the previous menu
(except for AUTO PROGRAM)
Press + or – to move the cursor (z) to the first
line (N) of each menu, and press ENTER.
Cancelling the menu screen
Press MENU.
SURROUND :
OFF
MONITOR
AV OUT :
FEATURES
TV SYS: D/K
AUTO PROGRAM
VHF LOW
PR: 01
TV SYS: D/K
VHF LOW
PR: 01
MANUAL PROGRAM

Getting Started -EN
9
MENU
ENTER
+
–
If you prefer English to Chinese, you can change the
menu language. You can use buttons on the remote
commander or the TV.
1Press Uto turn on the TV.
2Press MENU.
3Press + or – to move the cursor (z) to the
PRESET menu ( ), and press ENTER.
Changing the menu
language
4Make sure the cursor (z) appears beside
###/LANGUAGE, and press ENTER.
5Press + or – to select "ENGLISH", and press
ENTER.
All of the menus change to English.
6Press MENU to return to the normal screen.
AUTO
PROGR
–MENU+ ENTER
MENU
ENTER
+
–
ENTER
+
–
PRESET
SKIP: PR02 OFF
TV SYS: D/K
COL SYS : AUTO
ENGL I SH
AUTO PROGRAM
MANUAL PROGRAM
LANGUAGE / :
MENU

Getting Started
10-EN
MENU
ENTER
+
–
You can preset TV channels easily by storing all the
receivable channels automatically. You can also preset
channels manually or disable program positions (see
page 11 ).
Presetting channels automatically
You can preset up to 100 TV channels in numerical
sequence from the program position 1. You can preset
channels automatically using the button on the TV or
the menu.
1Press Uto turn on the TV.
2Press AUTO PROGR.
The TV starts scanning and presetting channels
automatically. When all of the receivable channels
are stored, the first preset TV program appears on
the screen.
Presetting channels To preset channels automatically using
the menu
1 Press MENU.
2 Press + or – to move the cursor (z) to the
PRESET menu ( ), and press ENTER.
3 Press + or – to move the cursor (z) to AUTO
PROGRAM, and press ENTER.
Presetting channels manually
To change the program position for a channel or to
receive a channel with a weak signal which you cannot
receive by automatic presetting, preset the channel
manually.
1Press MENU.
2Press + or – to move the cursor (z) to the
PRESET menu ( ), and press ENTER.
3Select your local TV system.
(1) Press + or – to move the cursor (z) to TV SYS, and
press ENTER.
(2) Press + or – until your local TV system appears on
the menu, and press ENTER.
4Press + or – to move the cursor (z) to
MANUAL PROGRAM, and press ENTER.
TV SYS:D/K
AUTO PROGRAM
VHF LOW
PR: 01
AUTO
PROGR
1
AUTO
PROGR
–MENU+ ENTER
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
ENTER
+
–
PRESET
SKIP: PR02 OFF
TV SYS: D/K
COL SYS : AUTO
ENGL I SH
AUTO PROGRAM
MANUAL PROGRAM
LANGUAGE / :
TV SYS:D/K
VHF LOW
PR: 01
MANUAL PROGRAM
ENTER
+
–

Getting Started -EN
11
Disabling program positions
By disabling unused or unwanted program positions,
you can skip those positions when you press PROGR
+/–.
1Press MENU.
2Press + or – to move the cursor (z) to the
PRESET menu ( ), and press ENTER.
3Press + or – to move the cursor (z) to SKIP,
and press ENTER.
4Press + or – until the unused or unwanted
program position appears on the menu,
and press ENTER.
5Press + or – to select ON, and press ENTER.
6To disable other program positions, repeat
steps 4 and 5.
7Press MENU to return to the normal screen.
To cancel the skip setting
1Display the PRESET menu.
2Press + or – to move the cursor (z) to SKIP, and
press ENTER.
3Press + or – until the program position you want to
cancel the skip setting appears, and press ENTER.
4Press + or – to select OFF, and press ENTER.
5Select the program position to which you
want to preset a channel.
(1) Make sure the cursor (z) appears beside PR, and
press ENTER.
(2) Press + or – until the program position you want
appears on the menu, and press ENTER.
6Select the desired channel.
(1) Press + or – to move the cursor (z) to VHF LOW,
and press ENTER.
(2) Press + or – until the desired channel picture
appears on the TV screen, and press ENTER.
7Press MENU to return to the normal screen.
If the TV system is not properly selected
The picture color may be poor and/or the sound may
be noisy. In this case, select the appropriate TV system.
1Press PROGR +/– or the number buttons to select
the program position.
2Display the PRESET menu.
3Press + or – to move the cursor (z) to TV SYS, and
press ENTER.
4Press + or – until the appropriate TV system
appears, and press ENTER.
Notes
• The TV system setting is memorized for each program
position.
• If you do not know your local TV system, consult your nearest
Sony dealer or authorized service center.

Operations
12-EN
Watching the TV To scan through program positions
Press PROGR +/– on the remote commander or the
TV until the program position you want appears.
3Press Á+/– on the remote commander or
the TV to adjust the volume.
Turning off the TV
To turn off the TV temporarily
Press Uon the remote commander. The uindicator
lights up.
To turn off the TV completely
Press Uon the TV.
Watching the video input
Press …on the remote commander or …on
the TV.
PROGR
1Press Uto turn on the TV.
When the TV is turned on in the standby mode
after pressing Uon the TV, press uon the remote
commander.
2Select the TV program you want to watch.
To select a program position directly
Press the number button.
To select a two-digit program position, press “÷”
before the number buttons.
For example: to select program position 25, press
“÷,” then “2” and “5.”
Operations
PROGR
123
456
789
0
-/--
25 -/--
VIDEO 1 VIDEO 2 VIDEO 3 1

Operations -EN
13
WAKE UP TIMER:10M
WAKE UP TIMER:OFF WAKE UP TIMER:12H00M
To watch TV
Press ;on the remote commander or …on the TV.
Switching back quickly to the previous
channel
Press JUMP.
Muting the sound
Press ¤.
Displaying the on-screen information
Press .
Note
The on-screen display shows the program position or the video
mode and the picture and sound information. The on-screen
display for the picture and sound information disappear after
being displayed for approximately three seconds.
Setting the Wake Up Timer
You can set the TV to turn on automatically after the
period of time you want.
1Press repeatedly to set the timer.
The on-screen display appears.
2If you want a particular TV program or
video mode to be displayed using the Wake
Up Timer, select the TV program or video
mode.
3Press uon the remote commander or set
the Sleep Timer to turn off the TV in the
standby mode.
The indicator lights up in amber color.
To cancel the Wake Up Timer, press repeatedly
until “WAKE UP TIMER: OFF” appears, or turn off the
main power of the TV.
Notes
• The Wake Up Timer starts immediately after the on-screen
display disappears.
• The last TV program position or video mode just before the TV
turns into the standby mode will appear when the TV is turned
on using the Wake Up Timer.
• If no buttons or controls are pressed for more than two hours
after the TV is turned on using the Wake Up Timer, the TV
automatically turns into the standby mode. If you want to
continue watching the TV, press any button or control on the
TV or remote commander.
After 10 minutes
After 12 hours
No Wake Up Timer
MUTING
DYNAMIC
8

Operations
14-EN
MENU
ENTER
+
–
Selecting the picture and sound modes
1Press MENU.
2Make sure the cursor (”) appears in the A/V
CONTROL menu ( ), and press ENTER.
3Press + or – to move the cursor (”) to
DYNAMIC, STANDARD, SOFT, or PERSONAL,
and press ENTER.
Select To
DYNAMIC Receive high contrast picture with
powerful sound.
STANDARD Receive normal contrast picture with
medium listening sound.
SOFT Receive mild picture with soft sound.
PERSONAL Receive the last picture and sound
settings that are adjusted using VIDEO
ADJUST and AUDIO ADJUST.
4Press MENU to return to the normal screen.
Setting the Sleep Timer
You can set the TV to turn off automatically after the
period of time you want.
Press .
To cancel the Sleep Timer, press repeatedly until
“SLEEP TIMER: OFF” appears, or turn the TV off.
After 30 minutes After 60 minutes
No Sleep Timer After 90 minutes
Adjusting the
picture and sound
SLEEP TIMER:30M SLEEP TIMER:60M
SLEEP TIMER:OFF SLEEP TIMER:90M
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
ENTER
+
–
MENU

Operations -EN
15
Press +
Increase picture
contrast.
Increase color
intensity.
Brighten the picture.
Make picture tones
become greenish.
Sharpen the picture.
Increase emphasis on
picture edges.
If the picture is slightly snowy
You may try to improve the picture by changing the
VM setting as described below:
1Display the VIDEO ADJUST menu.
2Press + or – to move the cursor (”) to VM, and
press ENTER.
3Press + or – to select LOW, and press ENTER.
If the picture color is abnormal when receiving
programs through the (antenna) terminal
Change the color system or the TV system from the
PRESET menu as described below until the color
becomes normal.
1Display the PRESET menu.
2Press + or – to move the cursor (”) to
COL SYS or TV SYS, and press ENTER.
3Press + or – to change the color system or the TV
system until the color becomes normal, and press
ENTER.
Note
Normally set the color system (COL SYS) to AUTO.
Adjusting the sound settings
(AUDIO ADJUST)
You can adjust the sound settings to suit your taste
with the AUDIO ADJUST option. The adjusted settings
are stored in the PERSONAL option.
1Press MENU.
2Make sure the cursor (”) appears in the A/V
CONTROL menu ( ), and press ENTER.
3Press + or – to move the cursor (”) to AUDIO
ADJUST, and press ENTER.
4Press + or – to move the cursor (”) to the
item you want to adjust, and press ENTER.
Continue to next page n
Adjusting the picture settings
(VIDEO ADJUST)
You can adjust the picture settings to suit your taste
with the VIDEO ADJUST option. The adjusted settings
are stored in the PERSONAL option.
1Press MENU.
2Make sure the cursor (”) appears in the A/V
CONTROL menu ( ), and press ENTER.
3Press + or – to move the cursor (”) to VIDEO
ADJUST, and press ENTER.
4Press + or – to move the cursor (”) to the
item you want to adjust, and press ENTER.
5Press + or – to adjust the selected item, and
press ENTER.
For details on each item, see “Description of adjustable
items” below.
6To adjust other items, repeat steps 4 and 5.
7Press MENU to return to the normal screen.
Description of adjustable items
Item Press –
PICTURE Decrease picture
contrast.
COLOR Decrease color
intensity.
BRIGHT Darken the picture.
HUE Make picture tones
become reddish.
SHARP Soften the picture.
VM Decrease emphasis
on picture edges.
Note
You can adjust HUE for the NTSC color system only.
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
P I CTURE
40
100
0
80
V I DEO ADJUST
COLOR
BR I GHT
HUE
SHARP
VM: HIGH
45
0
ENTER
+
–
A / V CONTROL
DYNAM I C
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
BASS 80
80
TREBLE
BALANCE
AUDIO ADJUST
00
ENTER
+
–

Operations
16-EN
MENU
ENTER
+
–
Press +
Increase the bass
sound.
Increase the treble
sound.
Increase the right
speaker's volume.
The 3D WOOFER enhances bold, dynamic and clear
sounds that spread over a large area and lets you enjoy
the thrills, horrors, and suspense of movies or music.
The initial setting of the 3D WOOFER is ON, and it is
ready for your listening when you turn on the TV.
To turn off the woofer sound
1Press MENU.
2Make sure the cursor (z) appears in the A/V
CONTROL menu ( ), and press ENTER.
3Press + or – to move the cursor (z) to AUDIO
ADJUST, and press ENTER.
4Press + or – to move the cursor (z) to
3D WOOFER, and press ENTER.
5Press + or – to select OFF, and press ENTER.
6Press MENU to return to the normal screen.
Notes
• To listen to the woofer sound, make sure that the 3D WOOFER
is properly connected to the TV (see page 6).
• You can also disconnect the 3D WOOFER from the TV to turn
off the woofer sound.
Listening to the
woofer sound
(3D WOOFER)
5Press + or – to adjust the selected item, and
press ENTER.
For details on each item, see “Description of adjustable
items” below.
6To adjust other items, repeat steps 4 and 5.
7Press MENU to return to the normal screen.
Description of adjustable items
Item Press –
BASS Decrease the bass
sound.
TREBLE Decrease the treble
sound.
BALANCE Increase the left
speaker's volume
If the sound is distorted or noisy when
receiving programs through the (antenna)
terminal
Change the TV system from the PRESET menu as
described below until the sound becomes normal.
1Display the PRESET menu.
2Press + or – to move the cursor (”) to TV SYS, and
press ENTER.
3Press + or – to change the TV system until the
sound becomes normal, and press ENTER.
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
ENTER
+
–
BASS 80
80
TREBLE
BALANCE
AUDIO ADJUST
00

Operations -EN
17
MENU
ENTER
+
–
The SURROUND feature enables you to enjoy a
surround sound effect that is like being in a large hall
or live concert when receiving stereo signals.
1Press MENU.
2Press + or – to move the cursor (z) to the
FEATURES menu ( ) , and press ENTER.
3Make sure the cursor (z) appears beside
SURROUND, and press ENTER.
4Press + or – to select HALL〈SRS〉, LIVE〈SRS〉,
or SPACE, and press ENTER.
For details on each item, see “Description of adjustable
items“ below.
5Press MENU to return to the normal screen.
Listening to the
surround sound
(SURROUND)
Description of adjustable items
Select To
HALL〈SRS〉Listen to a sound that spreads out over a
large area.
LIVE〈SRS〉Listen to the sound that gives the feeling
of being at a live concert.
SPACE Listen to a monaural sound that gives a
stereo-like effect.
OFF Turn off the surround sound.
Note
The µ® SRS (SOUND RETRIEVAL SYSTEM) is manufactured
by Sony Corporation under license from SRS Labs, Inc. It is
covered by U.S. Patent No. 4,748,669.
The word “SRS” and the SRS symbol µare registered
trademarks of SRS Labs, Inc.
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
LIVE〈SRS〉
zz HALL〈SRS〉
z
OFF
z
SPACE
SURROUND :
OFF
MON I TOR
AV OUT :
FEATURES
ENTER
+
–

Operations
18-EN
Adjusting the picture tilt
You can adjust the picture tilt if it is not aligned to the
TV screen. This may happen due to the direction of the
earth’s magnetic fields in relation to the TV position.
1Press MENU.
2Make sure the cursor (z) appears in the A/V
CONTROL menu ( ), and press ENTERp.
3Press + or – to move the cursor (z) to TILT
CORRECT, and press ENTER.
4Press + or – to select the most suitable
value to adjust the picture tilt, and press
ENTERp.
TILT CORRECT:
–5 N–4 N–3 N–2 N–1 N0 n+1 n+2 n+3 n+4 n+5
Press – Press +
Customizing the TV
Using the AV OUT (advanced rec-out)
terminal
You can select the output signal from the Ú
(MONITOR/TV OUT) jacks at the rear of the TV.
1Press MENU.
2Press + or – to move the cursor (z) to the
FEATURES menu ( ), and press ENTER.
3Press + or – to move the cursor (z) to AV
OUT, and press ENTER.
4Press + or – to select the output signal, and
press ENTER.
Select To
TV Output the signal of the TV broadcast.
MONITOR Output the signal of the picture you are
watching as a main picture.
Note
Do not change the channel while recording with a VCR through
the Ú(MONITOR/TV OUT) jacks. If you change the channel, it
also changes the channel you are recording.
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
A / V CONTROL
DYNAM IC
SOFT
STANDARD
PERSONAL
V I DEO ADJUST
AUDIO ADJUST
MENU
SURROUND :
OFF
MON I TOR
AV OUT :
FEATURES
ENTER
+
–

Operations -EN
19
No picture
No sound
/Press U.
/Press Uto turn off the TV for about five
seconds and then turn it on again.
/Check the power cord connection.
/Check the antenna connection.
/Check the VCR connections.
Good picture
No sound
/Press Á+.
/Press ¤.
No color
/Adjust the COLOR level in the VIDEO
ADJUST menu of the PERSONAL option.
/Check the color system (COL SYS) setting.
No sound from 3D WOOFER
/Check the connection of the 3D WOOFER.
TV cabinet creaks
/Even if the picture or the sound is normal,
changes in the room temperature
sometimes make the TV cabinet expand or
contract, making a noise. This does not
indicate a malfunction.
Troubleshooting
If you have any problems, read this manual again and
check the countermeasure for each of the symptoms
listed below.
If the problem persists after trying the methods below,
contact your nearest Sony dealer or authorized service
center.
Snowy picture
Noisy sound
/Check the antenna.
/Check the antenna connection on the TV
and on the wall.
/Check the TV system (TV SYS) setting.
Dotted lines or stripes
/This may be caused by local interference
(e.g. cars, neon signs, hair dryers, etc.).
Adjust the antenna for minimum
interference.
Double images or “ghosts”
/This may be caused by reflections from
nearby mountains or buildings. A highly
directional antenna may improve the
picture.
Good picture
Noisy sound
/Check the TV system (TV SYS) setting.
Additional Information
Additional Information

110-240 V AC, 50/60 Hz
Indicated on the rear of the TV
B/G, I, D/K, M
PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
VHF : E2 to E12 / UHF : E21 to E69 / CATV : S01 to S03, S1 to S41
UHF : B21 to B68 / CATV : S01 to S03, S1 to S41
VHF : C1 to C12, R1 to R12 / UHF : C13 to C57, R21 to R60 /
CATV: Z1 to Z39, S01 to S03, S1 to S41
VHF : A2 to A13 / UHF : A14 to A79/
CATV: A-8 to A-2, A to W+4, W+6 to W+84
75-ohm external terminal
5 W + 5 W + 15 W (3D WOOFER)
Input : 3 Output : 1 Phono jacks; 1 Vp-p, 75ohms
Input : 3 Output : 1 Phono jacks; 500 mVrms
Input : 1 Y: 1 Vp-p, 75 ohms,
unbalanced, sync negative
C: 0.286 Vp-p, 75 ohms
Output : 1 Minijack
Output : 1
Super Trinitron Plus
(29 in.)
72 Measured diagonally
68 Measured diagonally
782 x 593 x 534
49
KV-H29TF
Specifications
Sony Corporation Tokyo, Japan
Note
Power requirements
Power consumption (W)
Television system
Color system
Channel coverage
B/G
I
D/K
M
Antenna
Audio output (speaker)
Number of terminal
(Video)
(Audio)
(S Video)
2(Headphone)
3D WOOFER
Picture tube
Tube size (cm)
Screen size (cm)
Dimensions (w/h/d, mm)
Mass (kg)
Design and specifications are subject to change without notice.