Sorel CALEON User guide

Installation and operating instruction
°CALEON Thermostat
Read carefully before installation, commissioning and operation

Content
Safety Instructions 3
EG-Conformity 3
General instructions 3
Changes to the Unit 3
Warranty and Liability 3
Disposal and Pollutants 3
Description °CALEON Thermostat 4
Specifications 4
Scope of supply 4
Installation 5
°CALEON Installation 5
Sample wiring 6
Setup 6
Setup procedure 6
Operation 7
Overview of temperatures & humidity 7
Select Operating Mode 7
Main Menu 7
Expert Menu 8
Expert Menu Settings 8
Settings Functions 9
Set Operation Hours 10
Set Operation Hours 10
2

SAFETY INSTRUCTIONS
EG-Conformity
By affixing the CE mark to the unit the manufacturer declares that °CALEON Thermostat conforms to the following relevant safety regulations:
lEU low voltage directive 2014/35/EU
lEU electromagnetic compatibility directive 2014/30/EU
conforms. Conformity has been verified and the corresponding documentation and the EU declaration of conformity are kept on file by the man-
ufacturer.
General instructions
Please read carefully!
These installation and operating instructions containbasic instructions and important information regarding safety, installation, commissioning,
maintenance and the optimal use of the unit. Therefore these instructions must be read and understood completely by the installation
technician/specialist and by the system user before installation, commissioning and operation of the unit.
This unit is an automatic, electrical °CALEON Roomthermostat. Install the device only in dry rooms and under environmental conditions as described
under "Technical Data".
In addition, observe the applicable accident prevention regulations, the regulations of the Association of Electrical Engineering, the local power sup-
ply utility, the applicable DIN-EN standards and the installation and operating instructions for the additional system components. Installation, elec-
trical connection, commissioning and maintenance of the unit may only be carried out by specialists who possess the appropriate training.
Users: Make sure that the specialist gives you detailed information on the function and operation of the unit. Always keep these
instructions in the vicinity of the unit.
The manufacturer does not take over any liability for damage caused through improper usage or non-compliance of this manual!
Changes to the Unit
lChanges, additions to or conversion of the unit are not permitted without written permission from the manufacturer.
lIt is likewise forbidden to install additional components that have not beentested together with the unit.
lIf it becomes clear that safe operation of the unit is no longer possible, for example because of damage to the housing, turn the
Unit off immediately.
lAny parts of the unit or accessories that are not in perfect conditionmust be exchanged immediately.
lUse only original spare parts and accessories from the manufacturer.
lMarkings made on the unit at the factory must not be altered, removed or made illegible.
lOnly the settings described in these instructions may be set using the Unit.
Changes to the unit can compromise the safety and functionof the unit or the entire system.
Warranty and Liability
The Unit has beenmanufactured and tested withregard to high quality and safety requirements. The warranty and liability shallnot include, how-
ever, any injury to persons or material damage that is attributable to one or more of the following causes:
lFailure to observe these installation and operating instructions.
lImproper installation, commissioning, maintenance and operation.
lImproperly executed repairs.
lUnauthorized structural changes to the unit.
lUse of the device for other than its intended purpose.
lOperation above or below the limit valueslisted in the ‚Specifications‘ section.
lForce majeure.
Disposal and Pollutants
The unit conforms to the European RoHS 2011/65/EU for the restriction of the use of certainhazardous substances in electrical and electronic equip-
ment.
Under nocircumstances may the device be disposed of with the normal household waste. Dispose of the unit only at appro-
priate collectionpoints or ship it back to the seller or manufacturer.
3

DESCRIPTION °CALEON THERMOSTAT
Specifications
2-part, ABS plastic
75 mm x 95 mm x 30 mm
Glass front
Capacitive touch panel
Color display with 240x320 dots
2.8 inches (7 cm) diagonal
Intuitive user guidance
Deutsch
English
Español
Italiano
Français
Português
Electrical specifications:
Power supply 100 - 240 VAC, 50 - 60 Hz
Power consumption max. 2,5 W
Protection category IP20
Protection class / overvoltage category 0/III
Max. cable length
1-Wire Bus Optional, without function
Permissible Ambient Conditions
during operation 0 °C - 50 °C, no moisture condensation permitted
for transport/storage 0 °C - 60 °C, no moisture condensation permitted
Measuring range Outside the measuring ranges there are larger deviations
Internal temperature sensor 0 °C - 60°C Accuracy +/- 1 °C
Resolution 0,1 °C
Internal sensor for rel. humidity 0 % - 100 % Accuracy +/- 6 °C
Resolution 0,1 %
1-Wire temperature sensors Optional, without function
Other Specifications
Installation methods Wallinstallation, with/without wallsocket
Real Time Clock RTC with 24 hour power reserve
Scope of supply
l°CALEON Roomthermostat
l2 screws 3,5 x 35 mm and 2 plugs 6 mm for wall installation.
l°CALEON Thermostat installation guide
4

INSTALLATION
°CALEON Installation
Mount the unit at a suitable location.
Pay attention to suitable
environmental conditions.
Direct sunlight, sources of
heat and cold, e.g. radi-
ators and windows must
be avoided.
Strip cables by 75 mm max. and strip
the last 7-10 mm of the wires.
Unscrew the screw, remove the cable
cover and connect the electric as
described.
Only mains voltage, no
SELV!
Refit the base and fasten with screw.
Switch on mains voltage and place
°CALEON in operation.
The commissioning can be
accessed in the °CALEON
menu under Expert at any
time.
5

Sample wiring
SETUP
Setup procedure
Install device
Install the device as described (see" Samplewiring " on page 6).
Set Functions
Assign a switching output to the respective functionvia the "Expert" menu in the "Settings" menu item under "Functions" and parameterize it (see " Set-
tings Functions " on page 9).
6

OPERATION
Overview of temperatures & humidity
It displays room temperature and humidity.
If there is no activity for 60 sec., the device is
automatically switched to the overview.
Room temperature
Indicates the temperature of the selected
Space in 0.1 degree increments.
Room humidity
Is the relative humidity of
The selected space in 0.1 degree incre-
ments.
Select Operating Mode
Back
Navigate back tothe overview.
Location/Room
Displays the selected location/room.
Minus/Plus
Change the target temperature +/- 0.5 ° C.
Main menu
Navigate to the mainmenu
Operating modes
Specifies which operating mode (Normal,
Comfort, Eco and Off) is selected. The selec-
ted mode is shown in color. By pressing the
plus and minus keys it is possible to adjust
the setpoint temperature of the modes.
Main Menu
Overview > Operating Mode > Main Menu
Periods
Adjustment of individual heating times
for each weekday with copy function
for subsequent days.
Holiday
Set time and temperature for the
period of absence.
Expert
Standard settings such as language,
time and date, functional options and
factory setting.
7

Expert Menu
Overview > Operating Mode > Main Menu > Expert
Language Selection
The configuration of the device language.
Date & Time
The configuration of the time and date and
automatic summer/winter changeover.
Settings
Settings concerning basic functions suchas
sensor calibration, location and com-
missioning.
Service values
Information about the device version and mes-
sages such as restarts.
Factory Settings
The factory settings are restored in the device.
Expert Menu Settings
Overview > Operating Mode > Main Menu > Expert > Settings
Functions
Management of local control functions -
Thermostat and dehumidifier.
Location
Set where the device is installed (selection of
the room icon).
Sensor calibration
Used to adapt the temperature and humid-
ity of the said local sensor for the selected
area.
Display
Adjustment of display brightness.
8

Settings Functions
Overview > Operating Mode > Main Menu > Expert > Settings > Functions
Thermostat
Output: Switching output of the function.
Hysteresis: Heating hysteresis
of the thermostat function in relation to the
actual set room temperature.
Dehumidifier
Output: Switching output of the function.
Humidity: Setpoint of humidity.
Hysteresis: Hysteresis of the dehumidifier func-
tion with reference to the target value set
under humidity.
9

Set Operation Hours
Overview > Operating Mode > Main Menu > Timer
Adjustment of individual heating times
by a simple copy functionfor every day.
Previous/Next week
Selects the set day.
Operating modes
Selects the operating mode to individual
heating sections.
Clock
Time table of the selection in periods of
30 minutes increments.
Menu
Opens the copy function. This function
allows you to copy the heating times for
the next day, on Monday-Friday or
Monday-Sunday.
Set Operation Hours
Step 1
Use the arrow keys to select the desired day.
Step 2
Select the first heating mode
(Normal) - with the index finger
select the desired length of time.
The selected period is colored by
selecting the color of the operating
mode (normal = orange).
Step 3
Continue to the next mode (Turbo)
and proceed as described above,
select the time period for the Turbo
Mode.
Step 4
Continue to the next mode (Eco) and
proceed as described above,
select the time period for the Eco
Mode.
Step 5
Continue to the next mode (Off) and
proceed as described above,
select the time period for the Off
Mode.
Step 6
After the completion of the setting of the individual heating times, youhave the option of selecting times using the main menufor the next day, or to
copy Monday-Friday or Monday-Sunday.
10

Final declaration
Although these instruction have been created with the greatest possible care, the possibility of incorrect or incomplete information cannot be
excluded. Subject as a basic principle to errors and technical changes.
Date and time of installation:
Name of installation company:
Space for notes:
Your specialist dealer: Manufacturer:
SOREL GmbH Mikroelektronik
Reme-Str. 12
D - 58300 Wetter (Ruhr)
[phone]
[phone]
[e-mail]
www.sorel.de
Version: 03.07.2018
11