Sound Control Technologies RemoteCam2 User manual

RemoteCam2™
Installation Instructions
www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017
Thank you for choosing the Sound Control Technologies’ RemoteCam2™ camera integration kit!
Included in each RemoteCam2™ kit will be:
•1 Power Supply & cord (Currently all RemoteCam Kits
utilize the WPS-12) to provide power for the
RemotCam2™ electronics as well as the remote camera
up to 300’ from the head end. All the RemoteCam™ kits
use the same power supply. The power supply is AC 100-
240V~47-63HZ compliant.
•1 RemoteCam2™ Head End Module (RC2-HE) which
provides system power, control interface (RX, TX, GND &
IR) for the camera & one Component Analog video output
for the codec.
•1 RemoteCam2™ Camera Module with PowerSniffer™
(RC2-CE) that provides camera power, control (RX, TX,
GND & IR) and Component Analog video input for the
camera
•Documentation
•Specific cables (P/N according to the following chart)
Company
Codec
Camera
SCT Kit
Cables
Generic
Sony RMBR3000
Or
Generic
Head-End
EVI-HD1
EVI-HD7 (Analog)
BRC-Z330
BRC-Z700
BRC-H700
BRC-H900
RC2-HDS
RC2-003/RC2-004
RCC-H003 (Purchased Separately)
HD15/DVI cable by dealer (EVI-HD7)
RC2-112 (Purchased Separately)
Polycom HDX Series
Group Series
EagleEye I, II, III
IV-L (MPTZ-A) RC2-HDP RC2-001
RC2-101
Polycom HDX Series
Group Series EagleEye 1080 RC2-HDE
RC2-003
RC2-004
RC2-101
To proceed with the installation, insure that you have installed two CAT5e or CAT6 cable between the
camera installation site and the codec installation site.

www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017
The cable must be wired for either UTP 568A or UTP 568B. Please use the following scheme:
To install the RemoteCam2™ Kit, follow this step-by-step guide:
•Step 1
•Test and verify the Cat5e or Cat6 cables for UTP 568A or 568B wiring at a minimum of 30 feet and a
maximum of 300 feet.
•Step 2
•Install the RC2-HE Head-End Module at the rack/equipment location.
•Connect the power Cat5e or Cat6 cable to the RC2-HE module.
•
Connect the power supply to the RC2-HE Module.
•Step 3
•Using the PowerSniffer™, at the camera location connect to the UTP power cable. It should display
3 green LED’s.
•
Any other result, please re-terminate.
•
Step 4
•
Disconnect the power supply from the RC2-HE
•Step 5
•
Connect the CAT5e or CAT6 cables to the RC2-CE Camera Module.
•Step 6
•Connect provided cables between codec and RC2-HE module.
•Step 7
•Connect provided cables between camera and RC2-CE module.
•Visca
•The Visca loop, or daisy chain supports up to seven cameras. On supported applications SCT
supplies a Visca Out cable. This cable should be connected from the camera to the RC2-CE only
when there is a proceeding camera in the daisy chain. Utilizing this cable on the last camera in the
chain will terminate control of all cameras.
•Step 8
•Connect the SCT WPS-12 power supply to the RC2D-HE module
Head-End Module: 2 LEDs
The left LED will turn on when powered. Link is present when LED blinks (stays solid with brighter blink).
Press Cable Adapt button for 1 second. Both LED’s will turn on. Link is present when left LED blinks (displays
solid with brighter blink)
To reset calibration:Press and hold cable adapt until left LED displays solid.
Camera Module:
•LED will be Red until link is established. Solid Green when link is active.
•Step 9
•Enjoy!