Southern Enterprises FA980700TX User manual

Providence Convertible Fireplace Tower
FA980700TX – New Mahogany
FA980800TX – Antique White
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises Inc.
Customer Service 1-800-633-5096
[email protected]om
www.seidal.com

Providence Convertible Fireplace Tower
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
padded surface like carpet or blanket. Check that you have all parts indicated. Call customer service if
hardware is missing. Before beginning assembly, carefully study the diagrams below and sort your
hardware according to the pictures. Using the incorrect hardware will cause damage.
A Quantity
of 16
Wood Dowel
(
Ø
5/16
”
*
1
-
3/16
”
L
)
B Quantity
of 12
Bolt
(
Φ
1
/
4
”*
1
”
L
)
CQuantity
Of 12
Flat Washer
DQuantity
Of 6
Flat Head Screw (Φ3*20mmL)
EQuantity
Of 16
Round Head Screw (Φ3*12mmL)
F Quantity
Of 8
Flat Head Screw (Φ3*12mmL)
G Quantity
Of 1
Firebox (shipped in a separate carton)
H Quantity
Of 1
Magnet
I Quantity
Of 2
Flat Head Screw (Φ5/16”*7/8”L)
J Quantity
Of 2
Round Head Screw (Φ3mm*13.5mmL)
for Magnet
K Quantity
Of 4
Screw (Φ7MM*5/8”L)
L Quantity
Of 4
Bracket
M Quantity
Of 4
Screw (Φ7MM*1”L)
N Quantity
Of 4
Wall Anchor
O Quantity
Of 2
Plastic Strap
1 Quantity
Of 1
Front Top Panel

2 Quantity
Of 2
Back Top Panel
3 Quantity
Of 1
Left Frame
4 Quantity
Of 1
Right Frame
5 Quantity
Of 1
Middle Shelf Panel
6 Quantity
Of 1
Left Door
7 Quantity
Of 1
Right Door
8 Quantity
Of 1
Middle Shelf Panel
9 Quantity
Of 1
Bottom Panel
10 Quantity
Of 4
Leg
11 Quantity
Of 4
Leg
12 Quantity
Of 1
Back Panel
13 Quantity
Of 1
Wood Holder
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth.
Periodically apply furniture wax to renew
the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
Call Customer Service at 1-800-633-5096,
please call manufacturer for assistance,
questions or parts.
Assembly Tool Required
No.2 Phillips Screwdriver
(Not Included)

Providence Convertible Fireplace Tower
Assembly Instructions
Figure 1
Turn the middle shelf panel (5) over
and use 2pcs round head screws (J)
to connect magnet (H) to middle shelf
panel (5) with Phillips screwdriver.
Figure 2
Attach middle shelf panels (5) and (8)
to the left frame (3) by inserting wood
dowels (A). Repeat step with right
frame (4) and middle shelf panels (5)
and (8) for assembly.
Use 8pcs bolts (B) through 8pcs flat
washers (C) to connect the middle
shelf panels (5) and (8) to both side
panels (3) and (4).
Tighten bolts (B) with Phillips
screwdriver.
A
8
A
B
C
C
3
B
C
C
A
A
54
J
H
5

Providence Convertible Fireplace Tower
Assembly Instructions
Figure 3
Attach legs (10) to assembled unit by
rotating the legs (10) clockwise tightly
with hand.
Figure 4
Use legs (11) through bottom panel
(9) to connect bottom panel (9) to the
four legs (10) by rotating legs (11)
clockwise tightly with hand.
11
11
11
9
3
4
10
10

Providence Convertible Fireplace Tower
Assembly Instructions
Figure 5
Use 6pcs flat head screws (D) to
connect front top panel (1) to back
top panel (2) via attached hinges.
Tighten flat head screws (D) with
Phillips screwdriver.
Figure 6
Attach top panels (1) and (2) to
assembled unit by inserting 4pcs
wood dowels (A).
Use 4pcs bolts (B) through 4pcs flat
washers (C) to connect top panel (1)
and (2) to assembled unit.
Tighten bolts (B) with Phillips
screwdriver.
2
1
DDD
3
4
B
C
A
A
1
2
C

Figure 7
Attach the back panel (12) onto the
back of the unit by using 16pcs
screws (E).
Figure 8
Use 8pcs screws (F) to connect door
panels (6) and (7) to assembled unit
with Phillips screwdriver.
E
12
F

Providence Convertible Fireplace Tower
Assembly Instructions
Figure 9
Place firebox (G) into the back of the
unit.
Figure 10
Attach wood holder (13) by
inserting 2pcs flat head screws
(I) into corresponding predrilled holes
and tighten with Phillips screwdriver.
I13

Providence Convertible Fireplace Tower
Assembly Instructions
Figure 11
Use screws (K) to connect
brackets (L) to left frame (3) and
right frame (4) as shown.
Tighten screws (K) with Phillips
screwdriver.
Drill 1/4 inch pilot holes in near
proximity of brackets (L)
attached to the left frame (3) and
right frame (4), then, tap the
plastic anchor (N) into the wall.
Use screws (M) to connect
brackets (L) to plastic anchors (N)
on wall.
Tighten screws (M)
with Phillips screwdriver.
Move this item closed to the fastened
wall brackets (L) and tie in both
brackets (L) with plastic straps (O) as
shown in diagram.
Now you can enjoy your new
fireplace.
L
O
L

Please examine this product carefully upon immediate receipt. Any request for missing parts or damage
replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be
honored within this time frame.Parts will not be available for items arriving fully assembled. We do not
recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If
damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide
parts or replacement merchandise.
Please contact Southern Enterprises at 800-633-5096 or in Dallas 972-869-0111/ 9am – 4pm Mon-Fri Central
time if you have product issues or email us at se[email protected]. Please ask for customer service
representative for issues involving damages or replacement parts. Please ask for technical assistance
representative for any issues with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Parts Replacement Form
Customer Service 1-800-633-5096
[email protected]om
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019