Southwestern Bell Freedom Phone GH4000 User manual

2.4GHz Multi-Handset Digital Spread Spectrum
Cordless Telephone with Call Waiting Caller ID
Freedom Phone
R
Southwestern Bell
GH4000 Owner's Manual
Toll Free Help line 1-800-366-0937
http://www.swbfreedomphone.com
DIGITAL
SY S T E M
E PANDABLE
Southwestern Bell
FreedomPhone
SPREAD SPECTRUM
PAGE
ID
Caller
CHARGE
GHz
2.4
MULTI HANDSET
MNO
GHI5
*
4
PQRS
7
#
0
6
WXYZ
8
TUV
OPER
9
PROG
TALK
1
MEM
MUTE
DEL
FLASH
DEF
3
2
JKL
ABC
INTCM
REDIAL
PAUSE
CANCEL

LIMITED WARRANTY 30
SERVICE 29
PRODUCT CARE 28
TROUBLESHOOTING 26
CALLER ID OPERATION 24
TELEPHONE OPERATION 17
HANDSET MENU AND PROGRAMMING 15
HANDSET REGISTRATION 14
INSTALLATION 11
INTRODUCTION 9
FCC WANTS YOU TO KNOW 8
CHARGER INDICATOR 7
BASE UNIT CONTROLS AND INDICATORS 6
5
HANDSET CONTROLS, INDICATORS
4
SAFETY INSTRUCTIONS FOR BATTERIES
IMPORTANT SAFETY INSTRUCTIONS 3
CONTENTS
2

BEFORE USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS, INCLUDING THE
FOLLOWING
1.Read and understand all instructions.
2.Follow all warnings and instructions marked on the product.
3.Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water, for example, near a bath tub, wash bowl,
kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand or table. The product may
fall causing serious damage to the product.
6. Slots and openings in the cabinet and the back or bottom are provided for
ventilation, to protect it from overheating, these openings must not be blocked or
covered. The openings should never be blocked by placing the product on the bed,
sofa, rug, or other similar surface. This product should never be placed near or over
a radiator or heat register. This product should not be placed in a built-in installation
unless proper ventilation is provided.
7. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this product
where the cord will be damaged by persons walking on it.
9. Do not overload wall outlet extension cords, as this can result in the risk of fire or
electric shock.
10.Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in a risk of
fire or electric shock. Never spill liquid of any kind on this product.
11.To reduce the risk of electric shock, do not disassemble this product. Instead,
when some repair work is required, take the unit to a qualified technician. Opening
or removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance is subsequently used.
12.Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating instructions.
Adjust only those controls, that are covered by the operating instructions because
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to normal operation.
e. If the product has been dropped or cabinet has be damaged.
f. If the product exhibits a distinct change in performance.
13.Avoid using telephone(other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
14.Do not use the telephone to report a gas leak in the vicinity of the leak.
IMPORTANT SAFETY INSTRUCTIONS
3

Safety Instructions for Batteries
Handset Battery Pack
CAUTION:
GP60AAAH3BMX 3.6V 600mAh GPI INTERNATIONAL LIMITED
CONTAINS NICKEL-METAL
HYDRIDE BATTERY. BATTERY
MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
a. Do not dispose of the battery in a fire. The cell may explode. Check with local
codes for possible special disposal instructions.
b. Do not open or mutilate the battery. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
c. Exercise care in handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may
overheat and cause burns.
d. Charge the batteries provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
e. Observe proper polarity orientation between the battery(ies) and battery charger.
f. Do not mix old and new batteries in this product.
g. Do not mix batteries of different sizes or from different manufacturers in this product.
The EPA certified RBRC* Battery Recycling Seal on the nickel-Metal
Hydride(Ni-MH) battery indicates Southwestern Bell Freedom Phone Retail
Sales is voluntarily participating in an industry program to collect and recycle
these batteries at the end of their useful life, when taken out of service in the
United States or Canada. The RBRC program provides a convenient alternative
to placing used Ni-MH batteries into the trash or the municipal waste stream,
which may be illegal in your area. Please call 1-800-8-BATTERY for information
on Ni-MH battery recycling and disposal bans/restrictions in your area.
Southwestern Bell Freedom phone Retail Sales involvement in this program is
part of our commitment to preserving our environment and conserving our
natural resources.
*RBRC is registered trademark of the Rechargeable Battery Recycling Corporation.
Save These Instructions
R
SAFETY INSTRUCTIONS FOR BATTERIES
Danger of explosion if battery is incorrectly replaced. Use onlya Southwestern
Bell Freedom Phone approved battery pack in the handset of your GH4000
Cordless Telephone. To reduce the risk of fire or injury, always do the following
when replacing, discarding or charging battery, When handling the batteries,
be careful not to short the battery with conducting materials such as rings,
bracelets, and keys. The Battery or conducting material may overheat and
cause burns. Use only the following type and size ofbattery pack:
FOR HANDSET UNIT:
4

MNOGHI 5
*
4
PQRS
7
#
0
6
WXYZ
8
TUV
OPER
9
PROG
TALK
1
MEM
MUTE
DEL
FLASH
DEF
3
2
JKL
ABC
INTCM
REDIAL
PAUSE
CANCEL
HANDSET CONTROLS, INDICATORS
Antenna
INT Button: Press to
make or end Internal call
Talk button: Press to
make or end a call
Memory Button: Press
to store phone numbers
in memory or to call a
number you have stored
Flash Button: Press to
answer an incoming call
if you have Call Waiting
Redial Button: Press to
redial the last number
you called.
LCD DISPLAY
PROG/Cancel
Up/Down Button:
Press to enter the menu
and to scroll through the
menu items
Headset Jack: Connect
a headset for hands-free
conversations
Mute Button: Press to
prevent the caller from
hearing outside
conversations.
5
Removable Faceplate:
Use color to identify
handset charger location

DIGITAL
S Y S T E M
E PANDABLE
Southwestern Bell
Freedom Phone
SPREAD SPECTRUM
PAGE
ID
Caller
CHARGE
GHz
2.4
MULTI HANDSET
Telephone Line Jack
Connect the telephoneline
cord here.
9V 300mA Jack
Connect the AC adaptor cord
here.
1.Antenna
2.Charge LED
The Charger LEDwill be litand the
handset will display"CHARGING"
when the handset is in charger.
3.Page Button
Used to locatethe handset
2
3
BASE UNIT CONTROLS AND INDICATORS
6
1
DC 9V 300mA
TEL. LINE

CHARGER INDICATOR
Charger LED
The Charger LED will be lit and
the handset will display
"CHARGING" when the handset
is in charger.
7
MNOGHI 5
*
4
PQRS
7
#
0
6
WXYZ
8
TUV
OPER
9
PROG
TALK
1
MEM
MUTE
DEL
FLASH
DEF
3
2
JKL
ABC
INTCM
REDIAL
PAUSE
CANCEL
Removable Faceplates
Use different colored faceplates
to identify handset charger
location and matchdecor.
To remove/replace: Place finger
nail in groove opening at top of
attached faceplate. Gently pull
faceplate away from handset
until locking tabssnap out.
To attach a faceplate: Align the
protruding locking tabs on rear
side of faceplate with the
corresponding openings on the
handset face. Press faceplate in
until the tabs snap-lock closed
in place.

The REN is usefulto determinethe quantityof devices you may connectto your telephone
lineandstillhaveallof thosedevicesringwhenyour telephonenumber iscalled.Inmost,but
not allareas,thesumof theRENsof alldevicesconnectedtoonelineshouldnot exceedfive
(5.0).To be certainof thenumberof devicesyoumayconnectto yourline,as determinedby
theREN,youshouldcontact your localtelephonecompany todeterminethemaximumREN
foryourcallingarea.
If yourtelephoneequipmentcauses harm to the telephonenetwork, the telephonecompany
may discontinue your service temporarily.lf possible, they will notify you in advance. But if
advancenoticeisn'tpractical,you willbe notifiedas soon as possible.You willbe informedof
your right to file acomplaint withFCC.
Your telephone company may make changes in its facilities, equipment, operations, or
proceduresthat could affectthe proper functioningof your equipment. If they do you will be
notifiedinadvance to give youanopportunity to maintain uninterruptedtelephone service.If
youexperience trouble withthis telephone equipment,disconnect fromthe network untilthe
problemhasbeencorrectedor untilyouaresurethat theequipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company.
Connectingto party lines is subject to state tariffs.
Thisequipment ishearingaidcompatible.
Warning: Changes or modifications to this unit not expressly approved by the party
responsiblefor compliancecouldvoidtheuser'sauthoritytooperatetheequipment.
CAUTION: To maintain compliance with the FCC's RF exposure guidelines place the base
unitatleast 20cmfromnearby persons
NOTE: This equipment has been tested and found to comply with the limits for aClass B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonableprotectionagainst harmfulinterferenceinaresidentialinstallation.For body worn
operation, this phone has been tested and meets the FCC RF exposure guidelines when
usedwiththe belt clip suppliedor designatedfor this product.Use of other accessories may
not ensure compliance with FCC RF exposure guidelines.This equipment generates, uses
andcanradiate radio frequency energy and,if not installedandusedinaccordance with the
instructions,may cause harmful interference to radio communications.However,there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turningthe equipment off andon,the user is encouragedto try to correct the interference by
one or more of the following measures:
Reorientorrelocatethereceivingantenna.
Increasetheseparationbetweentheequipment andreceiver.
Connect theequipment intoanoutlet onacircuit different fromthat towhichthereceiver is
needed.
Consult thedealer or anexperiencedradioTV technicianfor help.
FCC WANTS YOU TO KNOW
8
This equipment complies with part 68 of the FCC rules and the requirements adopted
by the ACTA. On the bottom of this equipment is a label that contains, among other
information, a product identifier in the format US:2XGWI00B2G4G4NNN. If requested,
this number must be provided to the telephone company. And the Universal Service
Order Code (USOC). which is RJ-11C, for this equipment and that the Jack is FCC and
ACTA Compliant.
This device complies withpart 15 of the FCC rules.Operation is subject to the followingtwo
conditions: (1) This device may not cause harmful interference and (2) This device must
acceptany interferencereceived,includinginterferencethatmay causeundesiredoperation.
Privacyof communicationsmay not beensuredwhenusingthisphone.

FEATURES
Caller ID (40 Name and Number) with call waiting
95 Channels (auto selection)
LCD display (3-Linefor Handset)
10 Memories storedin Base and shared with all Handsets
Dual Keypad anddirect dialing from caller list
Digital security coding
Intercom Handset with Handset
Back light display
The GH4000 is a 2.4GHz/Digital Spread Spectrum Dual Keypad
Cordless Telephone With Caller ID, Call Waiting and Multiple
Handset Capability. It is designed and engineered to exacting
standards for reliability, long life, and outstanding performance.
ABOUT THE GH4000
The GH4000 allows you to answer a call by just removing the
Handset from the Charging cradle so you don't have to waste
time pushing buttons or flipping switches. lt also allows you to
hang up by simply returning the handset to the Charging cradle.
TM
The Ultra Clear Plus true compander circuitry virtually
eliminates background noise. This innovative technology,
together with 95 different channels, provides you with the best
possible reception duringyour conversations.
INTRODUCTION
9

Keep the shipping carton and packaging, in case you need to transport
your phone. If any of these items are missing or damaged, contact your
place of purchase.
NOTE:
Telephone Line Installation
1.Never install telephone jacks during a lightning storm.
2.Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
3.Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
4.Use caution when installing or modifying telephone lines.
Modular Outlet
The GH4000 cordless telephone requires a modular phone jack(RJ11)
and a standard 110/120 volt outlet. The handset is powered by a
rechargeable battery pack. Batteries are charged automatically when the
handset is placed in the .charging cradle
Box Contents
Base unit
Owner's manual
Memory card
Telephoneline cord
(long and short)
(2) Handsets
Handset Charger with adaptor
Multi Rechargeable Battery/
Beltclip
AC adaptor withcord for Base
Wall mounting bracket
Quick reference guide
Registration card
INTRODUCTION
10

INSTALLATION
Desk or Table Installation
1. Plug the AC adaptor cord into the 9V DC input jack on
the back of the Base unit.
2. Plug one end of the long telephone cord into the TEL
LINE jack on the back of the Base unit.
3. Plug the other end of the long telephone cord into the
telephone wall jack.
4. Plug the AC adaptor into a standard 110/120V 60Hz AC
wall outlet.
NOTE: Use only the AC adaptor supplied with GH4000.
Place the telephone and power cords where they
will not create a trip hazard, and where they can not
become chafed and create a fire or other electrical
hazard.
(Use only with class 2 power source 9V 300mA)
11
Standard Outlet
AC Adaptor
Modular Jack
Telephone line cord

Wall Mounting
The GH4000 may be mounted on a wall phone plate or onto two
screws (not included) that you fasten to the wall. For either type
of installation, completethe following stepsfirst.
1.When using thestandard wall plate, this step is not necessary.
Place the Wall bracket on the wall and mark the location of the
screws holes. Install the screws, leaving 3/16" extending out
from the wall. Use anchorsto secure screws.
2.To connect the Wall Mount bracket, align the bracket with the
slots on the base until it is securely in place.
3.Insert the ACadaptor into theback of the unit.
4. Plug one end of the short telephone line cord into the TEL
LINE jack onthe Base unit.
5. Thread the adaptor cord and telephone cord through the
grooves in thebracket. The cord will exitfrom the bottom.
DO NOT CONNECT THE AC ADAPTOR TO THE WALL POWER
OUTLET YET.
6. Plug theother end of the line cord into the walljack.
7. Mount the base on the wall plate studs and press until the unit
locks in place.
8. Plug the AC adaptor into a standard 110/120V 60Hz AC wall
outlet.
INSTALLATION
12

Handset Battery Charging:
The battery pack in the handset must be charged for about 10 hours
before using the telephone. After connecting to AC power, leave the
handset unused in the cradle for ten hours. Later, it will take less time
for the battery to recharge. The CHARGE LED on the handset charger
will be litand the handset will display "READY ".
To Replace Batteries:
1. Remove battery cover.
2. Remove old battery.
3. Plug the cord of the battery pack into the
handset and place the battery in the case.
4. Slide battery cover until it clicks in place.
Charge 10 hours before first use.
To maximize your battery's life, we recommend that you periodically
fully discharge the battery, and then recharge it. To do this, unplug your
phone line cord from the wall phone jack. Press the TALK button, and
allow the handset to remain on for 10 hours. Reconnect the phone cord
to the wall phone jack. Return the handset to the handset charger and
allow it to fully charge for 10 hours. If this process is completed monthly,
it will reduce the memory buildup that occurs from frequent partial
charging.
NOTE:
a. When the battery gets low, the Battery Low lndicator will
turn on.
b. If the battery becomes low while you are on a call, you
will be disconnected after about 30 seconds. Terminate the
call quickly, and put the handset in the handset charger to
recharge the battery.
c. The battery will hold its charge for several days out of
the cradle, dependingon use.
NOTE: The handset will not ring when the ringer is in the
"OFF" position. If the handset is out of the cradle, it will
display"RINGING" during anincoming call.
INSTALLATION
MNOGHI 5
*
4
PQRS
7
#
0
6
WXYZ
8
TUV
OPER
9
PROG
TALK
1
MEM
MUTE
DEL
FLASH
DEF
3
2
JKL
ABC
INTCM
REDIAL
PAUSE
CANCEL
CHARGE
Freedom Phone
Southwestern Bell
13

HANDSET REGISTRATION
When the handset is placed in the
base station registration outlet, it
transmits a registration packet to
the base station via the registration
outlet. The base station enables
registration and broadcasts
registration data via air interface.
Handset locks to this base station
and registration iscomplete.
When a new handset transmits a
registration packet toa base station,
the base station checks how many
handsets have been already
registered. In case 4 handsets are
already registered, the base station
starts to search for the handsets. If
it can locate all 4 handsets, then the
5th handset can't be registered, and
the registration is blocked. In case
a handset that already is registered
is out of range, or for other reasons
does not reply to the search and
notification request, it will be de-
registered and the registration
procedure for the new handset is
initiated.
The handset registration procedure
must be completed within 45
seconds.
The second handset cannot be
registered during an ongoing
registration procedure.
In case of heavy air interference,
e.g. when many 2.4GHz products
are active in the same area,
registration duration may be longer
since registration consists of data
transfer, that in contrast to audio,
has to be error free.
The way to de-register a handset
and register it to another base
station is to switch off the base
station and plug the handset in
another base station. After
switching off the base station, the
handset is no longer locked to this
base station and can be registered
to another base. When the handset
is connected to the other base
station registration outlet, a new
registration will take place and the
old registration doesn'texist.
Note: de-registration is not a
normal user operation.
IMPORTANT NOTE
1.Place each handset in the main
base unit toregister it tothe base.
2.Leave each unit in the base for up
to 15 seconds until a long beep is
heard, indicating thatthe handset is
registered to thebase unit.
3. The LCD display on the handset
will read "READY".
4. Make sure to do this for all
handsets.
14
ID
S Y S T E M
E PANDABLE
Caller
MULTI HANDSET
DIGITAL
Southwestern Bell
Freedom Phone
SPREAD SPECTRUM
PAGE
CHARGE
GHz
2.4
MNOGHI 5
*
4
PQRS
7
#
0
6
WXYZ
8
TUV
OPER
9
PROG
TALK
1
MEM
MUTE
DEL
FLASH
DEF
3
2
JKL
ABC
INTCM
REDIAL
PAUSE
CANCEL

Menu key functions
1.Press PROG key to enter the
menu.
2.Use the UP/DOWN keys to scroll
through the menu items. Pressing
DOWN at the last menu item
scrolls the menu to the first, and
pressing UP at the first menu item
scrolls to the last item. The
UP/DOWN keys include auto
repeat when helddown.
3.Press CANCEL to step back one
level in the menu (returns to idle
when in thefirst level ofthe menu).
4.Press PROG to choose the menu
item shown in the first line of the
display.
5.Enter setting/level number. Key
click is heard only after a valid
setting/level number.
6.Confirm setting/level by
pressing the PROG key. The
handset automatically returns to
the previous menulevel.
Audio Volume
Audio volume is adjusted by the
following key sequence
1.Press PROG
2.Press the DOWNkey two times.
3.Press PROG, to enter the volume
sub-menu.
4.Enter volume 1-8, or adjust using
DOWN/UP keys.
5.Press PROG, to confirm the
setting.
Ring Volume
The ring volume is adjusted by the
following key sequence
1.Press PROG
HANDSET MENU AND PROGRAMMING
2.Press the DOWNkey three times.
3.Press PROG, to enter the ring
volume sub-menu.
4.Enter volume 0..6, or adjust
using DOWN/UP keys. The current
ring tone/melody is played once at
the selected newvolume.
5.Press PROG, to confirm the
setting.
Ring pattern
The ring pattern of an
external/internal incoming call is
changed by the following key
sequence:
1.Press PROG
2.Press the DOWNkey four times.
3.Press PROG, to enter the ring
pattern sub-menu.
4.Press the UP/DOWN keys
followed by the PROG key to
choose either external or internal
ring pattern setting.
5. Enter setting0..9, or adjust using
DOWN/UP keys. The selected ring
pattern is played at the default
volume level inthe buzzer.
6.Press PROG, to confirm the
setting.
Auto Answer
The auto answer feature may be
configured using themenu.
1. Press PROG.
2.Press the DOWNkey five times.
3.Press PROG, to enter the auto
answer sub-menu.
4.Enable auto answer by pressing 1
or UP, or disable auto answer by
pressing the 0 or DOWN key. The
display shows theactual setting, i.e.
15

auto answer is activated with the
display text "ON".
5.Press PROG, to confirm the
setting.
Key Click
When the key click option is
enabled any key press generates a
key click sound in the buzzer,
except when the keypad is locked.
The key click option is configured
by the followingkey sequence.
1.Press PROG
2.Press the DOWNkey six times.
3.Press PROG, to enter the key
click sub-menu.
4.Enable key click by pressing 1 or
UP,or disable key click by pressing
the 0 orDOWN key.
5.Press PROG, to confirm the
setting.
Key lock
Locking the keypad
It is possible to lock the handset
keypad. The key lock function is
set/reset in thefollowing manner.
1.Press PROG.
2.Press the DOWNkey seven times.
3.Press PROG, to enter the key
lock sub-menu.
4.Enable key lock by pressing 1 or
UP, or disable key lock by pressing
the 0 orDOWN key.
5.Press PROG, to confirm the
setting. If ON was selected, the
phone locks the keypad and returns
to idle. A "key locked" status is
shown in the display while in the
standby mode.
HANDSET MENU AND PROGRAMMING
Unlocking the keypad
1.To unlock the keypad press the
key sequence '1','5','9'.Pressing
any key willdisplay a help message
to unlock thekeypad.
2.It is still possible to dial an
emergency call when the keypad is
locked by pressing TALK first and
then the emergency number
(000,110,112,119,911,999). Only
post-dial is possiblein this case.
Key lock is disabled after an
emergency call.
16

This section describeshow to
1.Answer an incomingexternal call
2.Answer an internal call
(intercom)
3.Make an externaloutgoing call
4.Make an internalcall
5.Forward an incoming external
call to theother handset
6.Setup a conference call (with the
other handset and an external
party)
7.Redial (last numbercalled)
8.Perform a Pagecall
9.Use the Flashfunction
Digital Security System
The security code prevents your
cordless telephone conversation
from being accessed by a phone on
a different line. Once the handset
battery is fully charged, the
handset will automatically select
the code froma total of over 65,000
combinations. The code is changed
every time the handset is placed in
the cradle. If you experience
difficulty with placing or receiving
calls, a lost security code may be
the cause of the problem. When
this occurs the handset can no
longer communicate with the base.
Reset by placing handset on base
for 5-10 seconds. If that does not
work, unplug the AC adaptor from
the wall outlet, disconnect the
handset battery for 5-10 seconds,
then reconnect. Replug the AC
adaptor and place handset on the
registration plug for5-10 seconds.
95 Channel Auto Scan
Operation
The GH4000 cordless telephone
automatically searches and selects
the clearest of 95channels when it
is being used.
Making a Call
1.Lift the handset and press the
TALK button to beconnected to the
phone line. "TALK" and the call
timer will bedisplayed.
2.After hearing a dial tone, dial the
desired number. The display will
show the dialednumber.
3.If you misdial, simply press the
TALK button and beginagain.
4.After your conversation is
competed, press the TALK button
once to disconnect the line, or
return the handsetto the charger.
The IN USELED will turnoff.
Receiving a Call
When the phonerings:
1.If the handset is out of the
charger, press TALK or any button
on the keypad.
2.If the handset is in the charger,
lift the handset. Do not press the
TALK button, as you will be
connected automatically.
NOTE:
If you experience difficulty with
placing or receiving calls, a lost
security code may be the cause of
the problem. When this occurs, the
handset can no longer
TELEPHONE OPERATION
17

communicate with its base. The
loss of the code can occur any of
the following ways: if the battery is
drained and needs recharging: the
handset is out of range of the base
unit; the AC adaptor is
disconnected or a power loss has
occurred; or anything that causes
electrical interference, for example
multiple cordless telephones.
(see Troubleshooting)
Headset Jack
You can connect a headset (not
included) for hands-free
conversations.
1.Insert the headset plug (must be
3/32 inch/2.5mm type)into the
headset jack on the side of the
handset (You may need to lift the
rubber protective cover from the
jack).
2.Attach the belt clip to the back of
the handset. Make sure the"arms"
of the belt clip snap securely into
the notches on the side of the
handset. You can now attach the
handset belt clip to the desired
location on yourclothing.
3.Adjust the headset microphone to
a comfortable position, placing it
near your mouth.
4.Use the TALK button to make or
receive a call.
5.To remove the belt clip from the
back of the handset, use your
fingernails to loosen one of the
"arms"of the belt clip. The other
"arm" of the belt clip will
automatically release from the
handset.
Incoming Call
The same procedure applies to all
incoming calls, i.e. external and
internal (intercom and conference
call).
Incoming Call -Handset
1.If auto answer is disabled, an
incoming call is accepted by
removing the handset from handset
charger, and pressing TALK or any
numerical key (0to 9), *or # key.
2.If auto answer is enabled, the
incoming call is accepted by
removing the handset from the
charger.
3.The call is terminated by
pressing TALK or placing the
handset in thecharger.
External Outgoing Call
Pre-dial
A call can be pre-dialed using the
following procedure..
1.Enter the phone number. In pre-
dial mode the number is displayed
in the first line. In case the number
exceeds 16 digits, it will continue
TELEPHONE OPERATION
18

into the secondline. A dial pause of
3 seconds will be inserted by
pressing the REDIAL key and it
will be indicated by the character
"P". The pause can't be used as the
first character, since as the first
character it would be treated as a
REDIAL command. AFlash cannot
be generated inpre-dial mode.
2.Check that the number is correct.
The last digit can be deleted by
pressing DELETE. The entire
number can be cleared by pressing
and holding the DELETE key.
3.Press TALK key(the phone calls
the entered number)
Post-dial
Setting up anexternal outgoing call
in a post-dialmode is made by.
1.Pass TALK key. The call timer
will start and 'External call' will be
shown in thedisplay.
2.Enter the number, which replaces
'External call' inthe display.
3.The display will show the
numbers as they are entered. If the
numbers exceeds 16 digits, the
number will be shifted to the
second line.
Terminatingan external
outgoing call
1.An external outgoing call is
terminated by pressing TALK or
placing the handsetin the charger.
2.After terminating an external
call, the timer stops running and
'Ended' will be displayed in the
first line ofthe display.
3.The call will be automatically
terminated if the handset
connection is lost, e.g. out of range
for 5 seconds.
Internal Call
An internal call is made by
pressing INT key, followed by
handset number ('0'-'4') after which
the call timer will start running and
'Internal call' will be shown in the
display.
It is also possible to select the
handset from a list, which will
appear after pressing the INT key.
Use the UP/DOWN key to scroll
through list and then select the
handset by pressing the TALK or
PROG key.
1.Press INT.
,
Name isn t assigned on the
receiving handset.
Internal handset name is assigned
TELEPHONE OPERATION
TALK 0:00:01
7890123496322300
TALK 0:00:01
EXTERNAL CALL
TALK 0:00:02
9876543210
ENDED 0:01:15
9876543210
SELECT INTERCOM
HANDSET #1
19
SELECT INTERCOM
SOMEBODY

on the receivinghandset.
Internal call to all handsets ( '*' -
call).
2.Press TALK or PROGkey
Name isn't assigned on the
receiving handset.
The call is connected and the call
timer starts. The handset numbers
can also be accessed directly by
pressing the INT key followed by
'1'-'4' or '*'key.
3.The call is terminated by
pressing TALK or placing the
handset in the Base after
terminating an internalcall.
Call Toggling
If a handset is engaged in an external
call, it is possible to establish an
internal call .
1.Pressing INT key to show a new
internal selection. Use up/down
keys to scroll through list of
registered handsets.
2.Selecting internal number by
pressing TALK, PROG or'1'-'4'.
3.The 'H' in the right hand side of
the second line indicates the
external call onhold.
It is possible to toggle between an
internal call and external call by
pressing the INT key. The 'H' is
also displayed when the internal
call is puton hold.
Call Transfer/Forward
An incoming call can be
transferred or forwarded to the
other handset during an ongoing
call.
Totransfer the call
1. Press INTkey .
2. Select handsetnumber in menu.
3. Press TALK or place the handset
in the charger after the other
handset has answered.
Toforward the call
1. Press INTkey
2. Select handsetnumber in menu.
3. Press TALK or place the handset
in the charger without waiting for
the answer.
Call Back
1.After call forwarding a call back
is generated in the forwarding
handset if the forwarded call is not
answered within 30 seconds. If
there is no CID information
available 'Call back'is shown inthe
display, otherwise normal CID
TELEPHONE OPERATION
SELECT INTERCOM
CALL ALL
TALK 0:00:01
HANDSET #1
TALK 1:35:06
HANDSET #1
TALK 1:35:50
EXTERNAL CALL H
SELECT INTERCOM
HANDSET #1
20