SP01 SMITH User manual

SMITH
DESIGNED BY METRICA
ASSEMBLY INSTRUCTIONS

DISCLAIMER
ENSURE THAT ALL STEPS ARE FOLLOWED IN THE CORRECT ORDER AND
THAT NO STEP IS LEFT OUT.
A MINIMUM OF TWO PEOPLE ARE REQUIRED FOR ASSEMBLY.
TO PREVENT ANY DAMAGE OF THE PRODUCT, DO NOT USE A BOX CUTTER,
KNIFE OR SHARP OBJECT TO OPEN THE BOXES.
DO NOT LIFT THE TABLE BY ITS TOP. IF YOU HAVE TO LIFT THE TABLE,
LIFT IT BY HOLDING ONTO THE METAL STRUCTURE.
SPØ1DESIGN.COM

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
SMITH TABLE WITH WOOD TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 4
SMITH TABLE WITH WOOD TOP
PACKAGING
PARTS
BOX WITH FRAME
AND TOP
LEG WITH METAL L,
SCREWS FOR ASSEMBLY
WOODEN TOP WITH
METAL FRAME WITH
WOODEN SIDES
BOX WITH LEGS

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 5
TOP DISASSEMBLY
PLACE THE FRAME WITH THE ALREADY ASSEMBLED TOP UPSIDE DOWN ONTO A SOFT AND CLEAN
SURFACE SUCH AS A BLANKET.
SMITH TABLE WITH WOOD TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 6
TOP DISASSEMBLY
UNSCREW THE TOP COMPLETELY AND SET ASIDE. THE TOP WILL BE REASSEMBLED AT THE END.
SMITH TABLE WITH WOOD TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 7
LOOSEN GENTLY ALL THE SCREWS WHICH FIX THE WOODEN SIDES ONTO THE METAL FRAME.
DO NOT UNSCREW THE WOODEN SIDES.
SMITH TABLE WITH WOOD TOP
STRUCTURE ASSEMBLY

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 8
STRUCTURE ASSEMBLY
ON A BLANKET, TILT THE METAL FRAME ONTO THE SIDE AND PLACE ONE SET OF THE LEGS INTO
POSITION. ENSURE THAT THE METAL L SITS CORRECTLY IN ITS POSITION.
FIX ONLY THE 3 SCREWS WHICH CONNECT THE WOODEN LEGS TO THE ENDS OF THE METAL FRAME.
REPEAT ON THE OTHER SIDE.
CHECK AND TIGHTEN THE INSERTED SCREWS.
SMITH TABLE WITH WOOD TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 9
NOW INSERT THE SCREWS FIXING THE METAL L ONTO THE WOODEN SIDES AND TIGHTEN.
REPEAT THE STEP ON THE OTHER SIDE.
SMITH TABLE WITH WOOD TOP
STRUCTURE ASSEMBLY

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 10
TIGHTEN ALL THE SCREWS WHICH FIX THE WOODEN SIDES ONTO THE METAL FRAME.
MAKE SURE THAT ALL SCREWS ARE TIGHTENED.
SMITH TABLE WITH WOOD TOP
STRUCTURE ASSEMBLY

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 11
WOOD TOP ASSEMBLY
PLACE THE TABLE TOP ON A BLANKET WITH THE UNDERSIDE FACING UP.
PLACE THE ASSEMBLED TABLE STRUCTURE ONTO THE WOODEN TOP AND GENTLY REASSEMBLE THE TOP
WITH ALL SCREWS.
DO NOT OVER-TIGHTEN THE SCREWS.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 12
SMITH TABLE
PLACE THE TABLE ON ITS LEGS, MAKING SURE THAT IT IS STABLE.
IF THE TABLE STRUCTURE IS MOVING TOO MUCH, RE-CHECK THAT ALL SCREWS ARE TIGHTENED
CORRECTLY.

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
SMITH TABLE WITH GLASS TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 14
SMITH TABLE WITH GLASS TOP
PACKAGING
PARTS
BOX WITH FRAME BOX WITH LEGSWOODEN CRATE WITH GLAS TOP
SELF-ADHESIVE RUBBERS LEG WITH METAL L,
SCREWS FOR ASSEMBLY
METAL FRAME WITH
WOODEN SIDES

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 15
PLACE THE FRAME UPSIDE DOWN ONTO A SOFT AND CLEAN SURFACE SUCH AS A BLANKET ON THE
FLOOR.
GENTLY LOOSEN THE SCREWS WHICH FIX THE WOODEN SIDES ONTO THE METAL FRAME.
DO NOT UNSCREW THE WOODEN SIDES.
SMITH TABLE WITH GLASS TOP
STRUCTURE ASSEMBLY

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 16
STRUCTURE ASSEMBLY
ON A BLANKET, TILT THE METAL FRAME ONTO THE SIDE AND PLACE ONE SET OF THE LEGS INTO
POSITION. ENSURE THAT THE METAL L SITS CORRECTLY IN ITS POSITION.
FIX ONLY THE 3 SCREWS WHICH CONNECT THE WOODEN LEGS TO THE ENDS OF THE METAL FRAME.
REPEAT ON THE OTHER SIDE.
CHECK AND TIGHTEN THE INSERTED SCREWS.
SMITH TABLE WITH GLASS TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 17
NOW INSERT THE SCREWS FIXING THE METAL L ONTO THE WOODEN SIDES AND TIGHTEN.
REPEAT THE STEP ON THE OTHER SIDE.
STRUCTURE ASSEMBLY
SMITH TABLE WITH GLASS TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 18
TIGHTEN ALL THE SCREWS WHICH FIX THE WOODEN SIDES ONTO THE METAL FRAME.
MAKE SURE THAT ALL SCREWS ARE TIGHTENED.
STRUCTURE ASSEMBLY
SMITH TABLE WITH GLASS TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 19
IF THE TABLE STRUCTURE IS MOVING TOO MUCH, RE-CHECK THAT ALL SCREWS ARE TIGHTENED
CORRECTLY.
STRUCTURE ASSEMBLY
SMITH TABLE WITH GLASS TOP

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 20
INSIDE THE PACKAGING/ATTACHED TO THE GLASS TOP ARE SELF-ADHESIVE RUBBER PADS.
GLUE THE RUBBER PADS ONTO THE WOODEN STRUCTURE AS SHOWN ABOVE.
GLAS TOP ASSEMBLY
SMITH TABLE WITH GLASS TOP