SP01 METRICA HOLLAND BENCH User manual

HOLLAND BENCH
DESIGNED BY METRICA
ASSEMBLY INSTRUCTIONS

DISCLAIMER
ENSURE THAT ALL STEPS ARE FOLLOWED IN THE CORRECT ORDER AND
THAT NO STEP IS LEFT OUT.
A MINIMUM OF TWO PEOPLE ARE REQUIRED FOR ASSEMBLY.
TO PREVENT ANY DAMAGE OF THE PRODUCT, DO NOT USE A BOX CUTTER,
KNIFE OR SHARP OBJECT TO OPEN THE BOXES.
DO NOT LIFT THE BENCH BY ITS TOP. IF YOU HAVE TO LIFT THE BENCH,
LIFT IT BY HOLDING ONTO THE METAL STRUCTURE.
SPØ1DESIGN.COM

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
HOLLAND BENCH
WITH BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 4
HOLLAND BENCH
WITH BACKREST
PACKAGING
BOX WITH METAL STRUCTURE
AND HARDWARE
BOX WITH WOODEN TOP BOX WITH METAL BACKREST
AND HARDWARE
2 METAL PLATES,
2 LONG SCREWS,
12 SHORT SCREWS
8 FELT PADS,
6 SCREWS
WOODEN TOP WITH CUT-OUTS FOR
BACKREST TUBE

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 5
BENCH ASSEMBLY
REMOVE THE BASE FROM ITS PACKAGING.
POSITION THE FELT PADS AS SHOWN ABOVE ONTO THE METAL FRAME. MAKE SURE THAT NO FELT PAD
COVERS ANY OF THE HOLES.
KEEP THE SCREWS IN A SECURE PLACE, YOU WILL NEED THEM FOR THE FINAL ASSEMBLY STEP.
IN THE MIDDLE OF ONE OF THE LONG RAILS YOU FIND THE SP01 LOGO. THIS WILL BE YOUR BACK SIDE
OF THE BENCH LATER.
HOLLAND BENCH
WITH BACKREST
SP01 LOGO

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 6
BENCH ASSEMBLY
REMOVE THE WOODEN TOP FROM ITS PACKAGING AND PLACE IT UPSIDE DOWN ONTO A SOFT AND CLEAN
SURFACE SUCH AS A BLANKET. THE SCREW HOLES SHOULD BE FACING UP.
THEN REMOVE THE BACKREST TUBE WITH HARDWARE FROM ITS PACKAGING.
HOLLAND BENCH
WITH BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 7
BENCH ASSEMBLY
POSITION THE METAL PLATE INTO THE CUT-OUTS OF THE WOODEN TOP ENSURING THAT ALL HOLES
MATCH. FIX THE METAL PLATE USING THE SHORT SCREWS PROVIDED WITHOUT TIGHTENING TOO MUCH.
HOLLAND BENCH
WITH BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 8
BENCH ASSEMBLY
TURN THE WOODEN TOP AROUND AND INSERT THE BACKREST TUBE CAREFULLY,
ENSURING THAT THE ANGLE OF THE BACKREST TUBE FACES THE BACK OF THE BENCH.
FROM BELOW, INSERT THE LONG CENTRAL SCREW WHICH FIXES THE BACKREST TUBE ONTO
THE WOODEN SEAT.
ONCE ALL SCREWS ARE INSERTED, GRADUALLY TIGHTEN ALL SCREWS.
HOLLAND BENCH
WITH BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 9
BENCH ASSEMBLY
HOLLAND BENCH
WITH BACKREST
PLACE THE ASSEMBLED SEAT ONTO THE STRUCTURE.
MAKE SURE THAT THE BACKREST TUBE IS ALIGNED WITH THE BASE FRAME.
NOW INSERT THE HARDWARE PROVIDED AND FIX THE TOP ONTO THE METAL STRUCTURE.
GRADUALLY TIGHTEN ALL THE SCREWS.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 10
HOLLAND BENCH
WITH BACKREST

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
HOLLAND BENCH
WITHOUT BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 12
HOLLAND BENCH
WITHOUT BACKREST
PACKAGING
BOX WITH METAL STRUCTURE
AND HARDWARE
BOX WITH WOODEN TOP
8 FELT PADS,
6 SCREWS

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 13
BENCH ASSEMBLY
REMOVE THE BASE FROM ITS PACKAGING.
POSITION THE FELT PADS AS SHOWN ABOVE ONTO THE METAL FRAME. MAKE SURE THAT NO FELT PAD
COVERS ANY OF THE HOLES.
KEEP THE SCREWS IN A SECURE PLACE, YOU WILL NEED THEM FOR THE FINAL ASSEMBLY STEP.
IN THE MIDDLE OF ONE OF THE LONG RAILS YOU FIND THE SP01 LOGO. THIS WILL BE YOUR BACK SIDE
OF THE BENCH LATER.
HOLLAND BENCH
WITHOUT BACKREST
SP01 LOGO

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 14
BENCH ASSEMBLY
REMOVE THE WOODEN TOP FROM ITS PACKAGING AND PLACE IT UPSIDE DOWN ONTO A SOFT AND CLEAN
SURFACE SUCH AS A BLANKET. THE SCREW HOLES SHOULD BE FACING UP.
HOLLAND BENCH
WITHOUT BACKREST

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 15
HOLLAND BENCH
WITHOUT BACKREST
BENCH ASSEMBLY
NOW PLACE THE METAL BASE UPSIDE DOWN ONTO THE WOODEN TOP AND FIX IT USING THE HARDWARE
PROVIDED. GRADUALLY TIGHTEN ALL SCREWS.
FINALLY TURN THE BENCH AROUND PLACING IT ONTO ITS LEGS.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 16
HOLLAND BENCH
WITH BACKREST