SP01 HOLLAND DESK User manual

HOLLAND DESK
DESIGNED BY METRICA
ASSEMBLY INSTRUCTIONS

DISCLAIMER
ENSURE THAT ALL STEPS ARE FOLLOWED IN THE CORRECT ORDER AND
THAT NO STEP IS LEFT OUT.
A MINIMUM OF TWO PEOPLE ARE REQUIRED FOR ASSEMBLY.
TO PREVENT ANY DAMAGE OF THE PRODUCT, DO NOT USE A BOX CUTTER,
KNIFE OR SHARP OBJECT TO OPEN THE BOXES.
DO NOT LIFT THE TABLE BY ITS TOP. IF YOU HAVE TO LIFT THE TABLE, LIFT
IT BY HOLDING ONTO THE METAL STRUCTURE.
IF YOU HAVE ANY OPTIONAL SUCH AS DRAWER AND/OR SCREEN, PLEASE
READ THE INSTRUCTIONS FOR YOUR OPTIONAL FIRST.
SPØ1DESIGN.COM

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
HOLLAND DESK

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 4
HOLLAND DESK
PACKAGING
PARTS
BOX WITH METAL BASE
WOODEN TOP WITH CABLE
MANAGEMENT HOLE AND
COVER
METAL BASE WITH ALREADY
ASSEMLBED FEET, 6 SCREWS AND
WASHERS AND 8 FELT PADS
BOX WITH TOP
6X
8X

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 5
TOP ASSEMBLY
ENSURE THAT THE ADJUSTABLE FEET ARE NOT TOO TIGHT, IN CASE LOOSEN THEM A LITTLE BIT.
IF YOU WISH TO HAVE CONTRASTING FEET, ENSURE TO CHANGE THE FEET.
POSITION THE FELT PADS AS SHOWN ABOVE MAKING SURE THAT THE PADS DO NOT COVER
ANY HOLE.
HOLLAND DESK

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 6
TOP ASSEMBLY
REMOVE THE WOODEN TOP FROM ITS PACAKGING AND PLACE IT UPSIDE DOWN ON A BLANKET/ SOFT
AND CLEAN SURFACE WHICH WILL NOT SCRATCH OR DAMAGE THE TOP.
HOLLAND DESK

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 7
TOP ASSEMBLY
PLACE THE METAL BASE ONTO THE TOP MAKING SURE THAT THE FOOTREST TUBE IS FACING OUT/
TOWARDS THE CABLE MANAGEMENT HOLE.
NOW INSERT THE SCREWS AND WASHERS FIXING THE STRUCTURE ONTO THE TOP USING THE PROVIDED
ALLEN KEY. TIGHTEN ALL THE SCREWS AND PLACE THE DESK ON ITS LEGS.
HOLLAND DESK

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 8
TOP ASSEMBLY
HOLLAND DESK
INSERT THE CABLE MANAGEMENT COVER INTO THE HOLE IN THE WOODEN TOP.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 9
HOLLAND DESK

SPØ1DESIGN.COM
ASSEMBLY INSTRUCTIONS
HOLLAND DRAWER
WE RECOMMEND TO MOUNT THE DRAWER BEFORE
MOUNTING THE FRAME TO THE DESK TOP.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 11
HOLLAND DESK DRAWER
PACKAGING
PARTS
BOX WITH DRAWER
WOODEN TOP WITH CABLE
MANAGEMENT HOLE AND
COVER
METAL DRAWER WITH METAL PIN AND PLATE
PLUS SCREW, 4 SCREWS, PLASTIC TUBE AND
PLATES, ROUND AND SQUARE PLASTIC BUMPERS
BOX WITH TOP
METAL PIN
METAL PLATE
SCREW
PLASTIC TUBE
PLASTIC PLATES
SCREWS PLASTIC BUMPERS

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 12
DRAWER ASSEMBLY
REMOVE THE WOODEN TOP FROM ITS PACAKGING AND PLACE IT UPSIDE DOWN ON A BLANKET/ SOFT
AND CLEAN SURFACE WHICH WILL NOT SCRATCH OR DAMAGE THE TOP.
HOLLAND DESK DRAWER

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 13
DRAWER ASSEMBLY
TAKE THE DRAWER AND ITS HARDWARE OUT OF THE BOX.
ENSURE TO CHOOSE THE CORRECT SIDE FOR ASSEMBLY OF YOUR LEFT OR RIGHT DARWER AS THEY ARE
NOT INTERCHANGEABLE.
HOLLAND DESK DRAWER

METAL PIN
© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 14
DRAWER ASSEMBLY
FIX THE METAL PIN WITH THE FOUR SHORT SCREWS PROVIDED ONTO THE TOP.
HOLLAND DESK DRAWER

PLASTIC DISK
METAL PIN
PLASTIC TUBE
© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 15
DRAWER ASSEMBLY
PLACE THE PLASTIC DISK AND TUBE ONTO THE ASSEMBLED METAL PIN COVERING THE METAL PARTS.
HOLLAND DESK DRAWER

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 16
DRAWER ASSEMBLY
PLACE THE DRAWER UPSIDE DOWN ONTO THE PIN.
HOLLAND DESK DRAWER

METAL DISK
PLASTIC DISK
© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 17
DRAWER ASSEMBLY
FIRST PLACE THE PLATIC PLATE AND THEN THE METAL PLATE AND FIX EVERYTHING WITH THE
SCREW PROVIDED.
HOLLAND DESK DRAWER

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 18
DRAWER ASSEMBLY
HOLLAND DESK DRAWER
MAKE SURE THAT THE DRAWER IS SITTING PARALLEL ON THE TOP.

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 19
DRAWER ASSEMBLY
PLACE THE SELF ADHESIVE ROUND OR SQUARE RUBBER STOPPER ONTO THE CLEAN WOODEN SURFACE.
IT SHOULD E POSITIONED ON THE BACK AND KEEP THE DRAWER IN POSITION.
NOW PROCEED WITH THE GENERAL DESK ASSEMBLY.
HOLLAND DESK DRAWER

© Copyright 2019 SP01 Design.
All rights reserved.
SPØ1DESIGN.COM
p. 20
HOLLAND DESK DRAWER