SpaDealers Polar AquaKing User manual

AquaKin
g


User’sGuide
WARNING!
Read the technical instructions before installing the bath
Read the users instructions before using the bath
Do not bring sharp objects into the bath
Contact the seller if the colours appear to be changing under or on top of the coating
If a leakage appears contact the seller immediately.
All electrical work should be perfomed by a qualified electrician
Do not leave children in the bath without supervision
Do not sit with your back or head against the skimmer
For AquaKing a mains connectionof 230V, 1x16A, 2x16A with Ground Fault Current Interrupt (GCFI) is required. A service
switch, which is closely installed to the electrical connection is recommended.
ATTENTION! If the hot tub will be integrated e.g. into a terrace it is necessary that the access is not obstructed in any way
order to be abletoservice it. Service hatch and outer panel should be removable without difficulties.
If automatic dispensers (floating, etc.) are used, careful adjustment should be made to avoid incorrect dosage. Follow the
recommendations in our instructions.
The circulation pump also generates heat and if it is running a long time (eg, continuous filtration TM) it can raise the
temperature by several degrees in one day when the tub is well insulated.
Check the quality of the water, as well as temperature and function, regularly, don't leave the spa unmonitored for long time
periods.

1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
Article Polar Part Number
AquaKing Material
LunaWood Page Size
A4
Designed by
JI 31.01.11
Checked by
Aproved by
Scale
1:18
Revision
v 2.4
Sheet
23/23
1114
626
394
2248 (2570)
2289 (2620)
1635(1920)
Water drainage
and electric wiring
850
210
200
Hose Ø 33 mm
~ 1814,5 (2057)

12
34

56
78

Picture 2 show how the air pump for the bubble system is placed.
It should not be oriented with the air exhaust upwards.
If the AquaKing is equipped with the BactiSafe (accessory) then it is positioned according to picture 1.
The control system is fastened in the position that is shown in picture 2.
Connect the nut to pump and filter properly (picture 3)
When installing the insulated box insulating foam (polyurethane) will be applied between the side insulation
of the spa bath and the boxe's insulation, see picture. The insulation beneath the lid of the box should not be
used when the temeprature indicates more than + 10 degrees. To protect BactiSafe against damage from
freezing it should be drained by loosening the stainless nut and the sealing around the glass tube.
Lowering into terrace ATTENTION! If the hot tub will be countersunk e.g. in a terrace it is necessary
that the access is not obstructed in any way order to be able to service it. Service hatch and outer panel should
be removable without difficulties.
1 2
3 4

CLEANING AND CHANGING THE FILTER






All screw connections must use the rubber seals provided. Own Assembly: During assembly of wall and base fittings, silicone
shall be used on both sides of the connections, as well as the threads.
ATTENTION! Near the bottom of the filter holder there is an arrow, which must be pointed towards the pump. The control system
should also be connected if it’s included. This must be doneby a qualified electrician. Close the valves on the filter before filling the
Hot Tub.
STARTUP
When the system is ready for testing, open the air screw (1) on top of the filter holder and the nut (2). Close it again when water
begins to leak out. After this procedure, the system is ready for use. Do not start the system without any water running and watch
out that both – the tap next to the filter (suction side) as well as the tap on the pressure side are open, meaning the part connected
to the pump (not the draining valve).
WATERLEVEL
The preferred water level for keeping the filtration working optimally is about 5 cm
below the skimmers upper edge. If it is beneath the skimmer, then the pump could
start sucking air instead of water into the filter and the control system then shuts off
the pump and heating.

3

2

B

B

A
1

CLEANING AND CHANGING THE FILTER


C
V
Cleaning /change of filter AquaKing For a good water hygiene it is very important
that the filter gets cleaned on a regular basis. At least every second week it should be
rinsed. Every second month or whenever it is required it needs to get cleaned
“thoroughly” with a special solution.
1. Open the hatch where filter and circulation pump are placed. Start the pump
(keep the T/A button pressed until it starts) if it’s not already running.
2. Open the screw (1) for the air above the filter top piece. Close the valve (3) on
the right side of the filter by pressing it down.
3. Be prepared to close the valve (C) (the one closest to the bottom to the left of
the pump) when the pump stops. This is important to do, so water will not flow
back into the filter cartridge holder.
4. Unscrew the nut and take off the filter’s top piece. Now it is possible to clean the
filter. It would be good to have a spare one. Assemble it in an opposite order
(tighten the nut on the cartridge holder, leave it slightly loose so it will be easier
to reopen it). Tighten the nuts of the filter container properly. Open 1 & 2 and let
air escape. Close when water starts trickling out. Now the pump can be started
via the control panel.
Draining of water There is a valve (V) close to the circulation pump installed in
order to drain water, see picture to the right. In case the spa bath needs to be
emptied for a longer period or if there might be a risk of frost then please keep in
mind to empty the circulation pump and the massage pump (if included) very
carefully as well.
1. Open cover where filter and pump(s) are installed. Open valve (V) and drain the
water via the drain hole.
2. Loosen the lowest nut belonging to the pumps (A). This one does not to be
loosened totally, just so that water can drain. Please do the same with the nuts
of the filter (B) and please do keep them open.
3. Loosen the nuts which are connected to the bubble system and give the hose a
good blow a few times till water runs out.
4. NOTE! If the control systems model nr. Is TM42-A1 then the blower air pump
can be started via the control panel. Let it run for a few seconds before turning it
off again.
Attention! When the spa is to be drained of water for a longer period of time, or if
there is a risk of freezing then the circulating pump, massage pumps and nuts for
pumps and filters shall be left open. If draining is done only for changing the water it
is not necessary to drain the pumps of water or open these connections. Also read “Avoid damage from freezing”.
Avoid damage from freezing
Plan the draining and filling of water so that there is no risk of damage from freezing, never empty or fill the bath when the temperature’s
below freezing without first protecting the equipment.
Attention! If the bath has been emptied of water and the temperature’s below freezing then all the equipment will also be below freezing
itself- If the bath is filled with water then without considering this, the risks of freezing damage is great.
For protection against freezing damages the interior of the bath can be warmed up beforehand. Use for instance an interior car heater or
electric heater and set the temp to 20 degrees celsius and place it inside the box where the pumps are installed as well.
If the water level drops below the massage nozzles they are automatically drained of water when the air regulator on the the edge is in
open moden. Is the air regulator is closed then water can remain in the transparent 12 mm hoses and cause freezing damage. Always
keep the air regulator in open mode when draining the spa.
To protect BactiSafe against damage from freezing it should be drained by loosening the stainless nut and the sealing around the glass
tube.

USERMANUALfortheSG‐0007BSYSTEM
Thisproductismeanttobeusedforelectroniccontroloffunctionsforspabaths.Pleasereadalloftheinstructions
carefullybeforeenjoyingthespa.WARNING:Operatingthesystemwithoutwaterwillcauseseveredamage.Contains
electroniccomponents,shockhazard.Doesnotcontainuserserviceableparts.Donottrytorepairthecontrolunit.
Contactyourdealerorservicecenterforhelp.Followalluserinstructions.
I.Installation
1) Openthedoor/coveraccordingtotheinstructionsandconnectthepower
supplycorrectly.
Warning
A. Installationisonlytobemadebyqualifiedpersons.
B. Readtheinstructionscarefullybeforebeginningtheinstallation.
C. Wearenotresponsibleiftheproductdoesnotworkorisdamagedwhenthe
instructionsarenotfollowedduringinstallation.
D. Ensurethatthesystemisnotdamagedduringtransportationwhenitisunpacked.
Note!
A. 1x16A(Read“Interlockedsystembetweentheheaterandpumps”),2x16Aor3x16shouldbeconnectedtothe
controlsystem.Donotconnectthepowerbeforetheinstallationiscomplete.
B. Installamaintenanceswitchclosetothecontrolsystemforuseduringmaintenancework.
C. Anearthswitchmustbeinstalled.Checkthattheearthswitchworkswhenthepowerisconnected.
















(Figure1)
WIRINGDIAGRAM3‐phase,2‐phase,1‐phase
SG0007BSketchOfLinkingWiresForTheSystem
(1)ConnectingL1,L2,L3,N,E
(L‐L:400V,L‐N:220‐240V)
(2)ConnectingL1,L2,N,E
(L‐L:400V,L‐N:220‐240V)
(3)ConnectingL1,N,Eonly
(L‐N:220‐240V)

II.Operatinginstructions













(Fig2)
ON/OFFkey(powerkey):ConnectthepowersupplyandpresstheON/OFFkey.Allthecontrolsystemsarenowreadytorun
(indicatorlightison),andthecirculationandOzonedisinfectionsystem(ifoneexists)willstartworkingautomatically(ifthe
watertemperatureisnotatthepre‐settemperature,theheatingsystemwillstarttoworkin60seconds).Thepanelwill
displaythecirculationandOzonesymbols(asymbolfortheheatingsystemwillalsobedisplayedonthepanelifthe
heatingsystemisworking).Thepanelwillalsodisplaythedetectedwatertemperature.Note!Ifnobuttonispressedwithin
60seconds,thedisplaysbacklightgoesoff,itreactivatesifabuttonispressed.
PUMPkey:pressthe(JET1)key.Itssymbolwillnowappearonthepanel,signifyingthatmassagepump1hasbeen
activated.JET2andJET3workinthesamewayandhavetheirownsymbolswithnumbers2and3onthem.JET1,JET2AND
JET3areaccessoriesforsomespamodels.NOTE:Themassagesystemwillshutdownautomaticallyin20minutes.NOTE:
Therearesomeairvalvesonthetopsideofspasneartheseats.Theyaretocontrolthestrengthofthehydro‐massageinthe
respectiveseats.
BUBBLEkey:Pressthekey.Itssymbolwillappearonthepanel,meaningthattheairmassagesystemhasstarted
working.NOTE:Theblowerautomaticallyshutsdownafter20minutes.
03key(Ozone):PressingtheO3keywillturnonorofftheOzonedisinfectionsystem(Ozoneandcirculationpumpwork
automaticallywhenactivatingthespa).NOTE!OzonecanbeanaccessoryandanotheralternativeistheUV‐Cozonecleaner.
See“UV‐COzoneCleaner”under“Summary”.
LAMPkey:Whenthecontrolsystemsarereadytowork,firstpressthekey.Itssymbolwillnowappearonthepanel,
signifyingthattheunderwaterlightsareon,thecolourwillchangeautomatically;withasecondpress,thecolorwillbefixed
onacertaincolor;pressforthethirdtimetoshutitoff.NOTE!Thelampshutsoffautomaticallyafter60minutes.
TEMPkey(needstobeusedtogetherwith▲/▼key):IftheTEMPkeyispressedfor5seconds,thepanelwilldisplaythe
watertemperaturesetlasttime.Thistemperaturewillkeepflashing:Pressthe“▲”keytoadjustthetemperaturetothe
highestat42°;pressthe“▼”keytoadjustthetemperaturetothelowestat10°.Thenewtemperaturewillbeautomatically
storedandthedisplaywillthenreturntoshowthecurrentwatertemperatureafterflashingfor60secondsoriftheor
buttonisused.
RADIO/AVkey(Radio/DVD/Controlanddisplayoftemperature):Whenthecontrolsystemsarereadytowork,pressthe
RADIO/AVkeytoactivatetheRadiofunction.Note:Speakersareoptional.Thepanelwillnowshowtheradiochannelset
lasttime(underRadiostatus,press+/‐keytoselectpre‐storedradiostations);asecondpresswillactivatetheTVfunction
(thisfunctionisoptional).ThepanelwillnowshowaTVsymbol.AthirdpresswillactivatetheDVDfunction(thisfunctionis
optional).ThepanelnowshowsaDVDsymbolatthesametime(UnderDVDstatus,pressthe+/‐keytoadjustthevolumeof
theDVD).Pressforthefourthtimetoshowthedetectedwatertemperature.
TUN/VOLkey(needstobeusedtogetherwiththe+/‐key):UnderRadiostatus,firstpresstheTUN/VOLkey.Thepanelwill
nowshowa2‐digitvolume,pressing+/‐willadjustthevolumeupwardsordownwards(thepanelwillautomaticallyshow
theradiofrequencywhenyoustopadjustingfor3seconds).Withasecondpress，thecurrentfrequencywillflash.Pressing

the+/‐keywilladjustthecurrentfrequency.Thisfrequencywillbestoredautomaticallyafterflashingfor3seconds.Witha
thirdpress,thepanelwillshowtheradiochannel.Pressthe+/‐ keytoselectpre‐storedradiostations(thepanelwill
automaticallyshowthepreviousradiofrequencyafteryoustopadjustingfor3seconds).Withalongpressfor5seconds,the
systemwillautomaticallysearchforradiofrequenciesagainandstorethesearchedfrequenciesatadifferentchannel
sequentially.
Heatingsystem:Afterthecontrolsystemsarereadytowork,theheaterwillstartworking60secondsafterthecirculation
pumpisactivated,unlessthetemperaturesensordetectsthatthesettemperatureislowerthanthedetectedone.When
thewatertemperaturereachesasettemperature,theheaterwillstopworkingautomatically.Whenthewatertemperature
isunder2°ofthepresetone,theheaterwillreactivate.Thesymbolfortheheaterislocatedabovethecirculationpump
symbol,itappearsaspulsingbubbles.
NOTE:Theheaterwillnotbeactivatedifthereisnotenoughwaterflow.
Interlockedsystembetweentheheaterandpumps:PressingandholdingtheON/OFFkeyagainfor20secondswillchange
thesystembetweeninterlockmodeornon‐interlockmode(theindicatorlightontheON/OFFkeyshowsREDininterlock
mode;whileitshowsGREENinnon‐interlockmode).Whenininterlockmode,theheaterwillstopwhenyoupressanyof
thepumpandbubblekeys.Thisfeatureismeanttoreducethepowerneededforthespasothatitcanmatchthepower
limitofsomecountries(1x16A).Innon‐interlockedmode,theheaterwillkeeprunningwhentheotherpumpsare
activatedunlessthewatertemperaturereachesthesettemperature.NOTE!Thatrequiresatleasta2‐phaseconnectionif
thetotaleffectforpumpsandheatingexceeds3680W.
Temperaturesensorself‐checkingsystem:IfE1isdisplayedonthepanel,thenthetemperaturesensorisdisconnected.In
thissituationcheckthewiringofthetemperaturesensortoseeifit’sproperlyconnected.IfE0isdisplayedonthepanel,
thenthetemperaturesensorhasshort‐circuited.Inthiscase,thetemperaturesensormustbereplaced.Theheatingsystem
cannotbeactivatedunderthetwoabovesituations.
Water‐lackingprotectionsystemforcirculationpumpandheater:Indailyusage,ablockageofthefiltrationmedium
(cartridgefilterorfilterbag)willeventuallyoccur.Asevereblockagewillleadtoalackofwaterforthefiltrationpump.Airin
thesystemoftenleadstothesameproblem.Forinstance,duringstartupifaerationhasnotbeenperformedaccordingto
theinstructionsinthemanual.Whenthereisalackofwater,thefiltrationpumpandheaterwillstopworkingautomatically.
Atthismoment,thesymbolofthefiltrationpumponthecontrolpanelwillflashcontinuously,toremindtheuserthat
itistimetocleanorreplacethefiltrationmedium.Aftercleaningorreplacingthefiltrationmedium,pressON/OFFseveral
timestoexpeltheairinsidethepipeuntilthefiltrationpumpworksnormally.
Frostprotectionmode:Ifthewatertemperaturedropsbelow10°Candthecirculationpumpspressureswitchhasnotbeen
activated(mayoccurduringfillingifthereisairinthesystem),thesystementers"Frostprotectionmode"andtheairpump
starts.WhenFrostprotectionmodeisactivated,nosymbolsappearonthedisplay.NOTE!ThesystemgoesintoFrost
protectionmodeonlyifthepressureswitchisnotactivated.Thenthepumpsymbolflashesinthelowerrightcorner,when
theOn/Offbuttonispressedtheairpumpstarts.Torestartthepump,thepowermustbedisconnectedandreconnectedvia
theserviceswitch.Whenthepumppressureswitchisactivated,thesystemwillnormallyresume.

Manualworkingmode:Turnonthespa,thenpressandholdthekeyfor3secondstoentermanualmode(theindicatorlight
onthekeywillshowGREENwheninmanualmode,indicatorkey3willlightup).Ifisselectedthefiltrationpump
(andthusthefiltration)isoncontinuously,24hperdaywithoutstoppinginbetween.

Automaticworkingmode:Automaticworkingmodeisonbydefault.Pressandholdthekeyfor3secondstoswitchoverto
automaticmode(Thebuttonwilllightup).Thecirculationpumpstartsandrunsfor1hour(thedisplaypanelwillcycle
between"ON"andwatertemperature,indicatorkey1willlightup).After1hourthepumpwillstopfor3hours(thedisplay
panelwillcyclebetween"OFF"andwatertemperature,indicatorkey2willlightup).Aslongasthesystemisinautomaticmode
thisfiltrationcyclewillrepeatindefinitely.

Thekeys1,2and3(FILTERPROGRAM)arenon‐functionalkeysandonlyactasindicators.


NOTE:
Ifthespaisinautomaticworkingmode,pleasedon’tturnoffthespawhennotinuse.Makesurethespais
always“on”.
Wheninautomaticmode,thefiltrationpumpwillalsobecontrolledbytemperature.Ifthewatertemperature
islowerthanthepresetlevel,duringthe“OFF”period,thefiltrationpumpandheaterwillworkuntilthewater
temperaturehasreachedthepresetlevel.Then,thefiltrationpumpwillreturntoworkfor1hourandstopfor
3hoursrepeatedly.Whentheautomaticmodeisnotinusethecirculationpumpisalwayson.Ifthewater
temperaturedrops2°underthepre‐setleveltheheaterwillactivate.
Eachtimethespaisswitchedon,thesystemwillgointothepreviouslysetmode.Pressandholdtheor
keyfor3seconds(theindicatorwillshowGREEN)toswitchbetweenautomaticmodeandmanualmode.

Summary:and
Ifisselectedthefiltrationishandledautomaticallyincyclesof“1houron,3hoursoff”.
Ifisselectedthefiltrationpump(andthusthefiltration)isoncontinuously,24hperdaywithoutstoppinginbetween.
Ifthepresettemperatureishigherthantheactualwatertemperaturethenboththecirculationpumpandheaterareactivated
untilthewatertemperaturereachesthechosensetting.TheOzonewillautomaticallyworktogetherwiththefiltrationpump
andheater.Thisappliesinbothandmodes.

WARNING!Thecirculationpumpalsogeneratesheatandifitisrunningalongtime(eg,continuousfiltration)itcanraisethe
temperaturebyseveraldegreesinonedaywhenthetubiswellinsulated.Avoidusingthefunctionothertimesthanwhen
thewaterneedstobefilteredfurther.Alwayscheckwaterqualityandtemperatureafterusingforoneday.

FILTRATIONPUMP‐NOTE!Ifthehottubisequippedwithamassagepumpitwillconnectedto"WATERPUMP1".Ifthereare
twomassagepumpsthesecondisconnectedto"WATERPUMP2".
UV‐COZONECLEANERIfanUV‐Cozonecleanerisinstalled,connectitsothatitactivatesthesametimeasthecirculatory
pump.
BLOWER(BUBBLE)‐ATTENTI ON!Iftheblowerisusedoftenandforprolongedperiodsoftime,theblowersbuiltinthermal
protectionmightactivate.Theblowerwillstopandnotrestartuntilit'scooleddownenough.Youcanspeedupthecoolingby
openingtheservicehatch(es).Indoingso,pleaseprotecttheequipmentfrompotentialfreezingdamage.