Speco Intensifier O2iD8M User manual

Intensifier® IP Dome Camera with Motorized Lens
QUICK INSTALLATION GUIDE
O2iD8M
Please read this manual carefully before installation and operation of the product.

1
Notice
Thank you for purchasing this product. This guide is designed to be a reference tool for the product.
Please read it carefully before operating the product and retain it for future reference. Should you
require any technical assistance, please contact Speco Technologies Technical Support.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority
to operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and
to obtain the best picture quality.
Please keep the manual in good condition for your future reference and service application.
Installation and services should only be carried out by an authorized personnel according to local
safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
This installation should be made by a qualified service person and should conform to all local codes.
CAUTION
TO REDUCE THE RISK OF ELECTRLC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRLC
SHOCK
DO NOT OPEN
CAUTION

2
supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need
maintenance by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality all the time.
Be careful not to be stained by fingerprint.
Don't face the camera directly toward sunlight or sunlight reflecting area.
IMAGE SENSOR may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock during the
process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the IMAGE SENSOR.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including
but not limited to, the implied warranties of merchantability, fitness for any particular purpose, or
non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to
the information herein, at any time, for the improvements of this publication and / or the corresponding
product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable
maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassemble, repair or modification of the product by the user.
(4) Inconvenience or any loss arising when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the system
combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being photogenic subject,
due to violation of privacy with the result of that surveillance-camera's or video server’s picture,
including saved data, for some reason, becomes public or is used for the purpose other than
surveillance.
1. PRODUCT OVERVIEW
Key Features
8.5 Mega pixel 1/2.5" SONY progressive scan CMOS image sensor for excellent image quality
Vandal Proof, fire resistant and tamper resistant
Perfect tool-free 3-Axis mechanism inside
Extended IR life cycle
Dust and Moisture free (IP67 Waterproof)

3
Triple Streaming of H.265, H.264 and M-JPEG
Supports image resolutions UHD-1 (3840 x 2160)
Integrated motion detection with pre- and post-alarm image / video buffering
Supports CBR (Constant Bit Rate) and VBR (Variable Bit Rate) modes
Supports Tampering-Alarm in VA (Video Analytics) function
Controllable frame rate
Full Duplex Two-Way Audio Support
External Audio Line-input & Audio Line-output connector
External sensors or external alarm devices
Privacy Masking
Supports IEEE 802.3af Power over Ethernet injectors, mid- and end-spans
HTTPS supported (Hyper Text Transfer Protocol Secured)
Integrated E-Mail, FTP, DDNS and DHCP client
Specification
CLASSIFICATION
Vandal Proof Armor Dome Camera
General
CPU
ARM1176JZF-STM ( 400 MHz, Instruction cache : 32kbyte,
data cache : 16kbyte, MMU )
Flash
2Gbit Flash Memory
SDRAM
2Gbit DDR3 Memory
Camera
Image Sensor
2.0 Megapixel 1/2.9" SONY progressive scan CMOS image
sensor
Total Pixels
1952(H) x 1116(V) 2.18 Megapixel
Effective Pixels
1944(H) x 1104(V) 2.14 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0Lux (IR On)
IR Distance
40M
Day & Night
ICR Filter Changer
Lens Control
Motorized Lens Control
Lens
2.7 ~ 12mm Vari-focal Motorized Megapixel Lens
Video
Video Compression
H.264 High profile
Resolutions
Up to 1920 x 1080
Frame Rate
H.264 Up to 30fps with 1920 x 1080, H.264 Up to 30fps with VGA
MJPEG Up to 30fps with VGA resolution
Video Streaming
Support multi stream with H.264, MJPEG
Adjustable frame rate
VBR / CBR in H.264
Image Setting
Brightness, Contrast, Sharpness
Day & Night
Auto White Balance
Auto Exposure
Privacy Mask
DSS, Corridor-view (in H.264), Mirror / V-Flip, etc.
Backlight
WDR (Low / Middle / High)
Shutter Speed
1/4 ~ 1/2000
Noise Reduction
2D / 3DNR
Audio
Audio Streaming
Two-way, full duplex
Audio Compression
G.711
Data / Sample Rate
64Kbps / 8KHz
Audio Input /
Output
Microphone input / 1x Line-In, Line-Output / 1x Line-Out
Network
Security
Password protection
User access log
HTTPS encryption
Supported Protocol
HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP
System
Intelligent Video
Motion detection 12 x 12 blocks

4
Integration
Alarm Trigger
Motion detection, External Input (NO / NC Type)
Video Buffer
5MB pre-alarm and post-alarm-180sec
Firmware Upgrade
Remote upgrade via network
API
CGI Interface document
Reset Bottom
1 x Factory Reset Button
Physical
Power Source
DC 12V / 1.5A, PoE (Power over Ethernet) : 802.3af
Power
Consumption
Max. 7.6W with IR On
Net Weight
1200g
LED's
Power, Network Connection
Dimension(mm)
Ø130 x 99(mm) / Junction Box : Ø130 x 145(mm)
Environment
Operating
Temperature
-10 degree ~ 50 degree Celsius (-14F ~ 122F)
Storage
Temperature
-20 degree ~ 60 degree Celsius (-4F ~ 140F)
Software
Included Software
IP Scanner (Windows only)
Package
Package Contents
Network Camera, Use Manual, External Power Adaptor
(Option)
Specifications are subject to change without prior notice.
2. NAME AND FUNCTION OF EACH PART
2.1 Package Contents
APPEARANCE
DESCRIPTION

5
IP Camera x 1
Installation Guide x 1
Drilling Template x 1
L-Wrench x 1
Tapping Screws(Ø4 x 30)x 3
Plastic Anchor x 3
CD x 1
Junction Box
Tapping Screws (Ø4 x 30)x 4
Plastic Anchor x 4
Silicone Template x 1
Junction Box x 1
Screw PH (M4 x 12) x 3
L-Wrench x 1

6
2.2 Name and Function
NO.
ITEM
DESCRIPTION
Power Connector
DC12V
Network and POE
Connector
POE (Power Over Ethernet) and LAN cable
Sensor In / Alarm Out
Sensor In / Alarm out
Audio-In
Audio in (Red)
Audio-Out
Audio Out (White)
IR LED
Infrared LED
Lens
2.7 ~ 12mm Motorized Megapixel Lens
luminance sensor
Control IR LED by sensing light
Heater
Resistors reduce condensation on front glass
7
1
2
3
4
5
6
7
8
4
5
2
3
1
6
8
9
9

7
3. INSTALLATION
3.1 Installation overview
Ceiling
①Paste a Drilling Template on the ceiling or wall and drill screw points which will be dome for
installation.
②Fix the Surface Mounting Base by using Tapping Screws provided.
③Fix the Flush mount Base on Surface Mounting Base.
④Turn the camera Ass’y to the desired direction.
⑤Turn the dome and shied cover to the camera direction.
⑥Fix the Dome Cover Ass’y to the Flush mount Base by using Torx Screw and Torx L-Wrench.
Ceiling Tile
Drilling Template
Top Cover Ass'y
Camera Ass'y
Plastic Anchor x 3
Tapping Screw (4 x 30) x 3
L-Wrench

8
Ceiling_Junction Box
3.2 3-Axis Adjustment
Tilt 85°
Rotate 180°
Tool-free 3-Axis mounting mechanism
Perfect Tri-axis!
Panning axis up to 345° degree.
Tilting axis up to 85° degree.
Rotation axis up to 180° degree.
No need to use a tool for adjustment!
All adjustments are done quick and
easy by hand!
Ceiling Tile
Drilling Template (Silicone)
Plastic Anchor x 4
Junction box
Tapping Screw (4 x 30) x 4
Camera Ass'y
PH (M4 x 12) x 3
L-Wrench
Top cover Ass'y

9
3.3 INSTALLATION EXAMPLE
3.3.1 Installation Example
3.3.2 Connecting Network
Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
Pan 345°
LAN Switch Router Internet Remote Access
LocalAccess E-Mail / FTP

10
3.3.3 Accessing the Camera or video server’s Homepage
1) Open the browser and input network camera address in the address bar or double click the device in IP
Scanner.
2) Please input your user name and password when prompted.
3) Default user name is admin and password is 1234.
4) The first time you login to the camera, you will be notified that a ActiveX control is required to be installed.
You need to allow the installation of ActiveX.
Input your IP
address here

11
4. DIMENSION (mm)
Ceiling
Ceiling_Junction Box