Speco Intensifier O2iD8 User manual

Intensifier® IP Dome Camera
QUICK INSTALLATION GUIDE
O2iD8
Please read this guide carefully before installation and operation of the product.

1
Notice
Thank you for purchasing this product. This guide is designed to be a reference tool for the product. Please read
it carefully before operating the product and retain it for future reference. Should you require any technical
assistance, please contact Speco Technologies Technical Support.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at its own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment.
CAUTION –To prevent electric shock and risk of the fire hazards
Do NOT use power source other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and should conform to all local codes.
The lighting flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of non-insulated dangerous voltage within
the product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION

2
PRECAUTIONS
Please read the manual carefully before the installation in order to set up the camera correctly and to obtain
the best picture quality.
Installation and services should only be carried out by an authorized personnel according to local safety
regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera from power supply and
have it checked by your authorized dealer before reusing.
Avoid installing the camera in extremely hot or cold places.
If you are not a certified person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside that need maintenance
by the user. All maintenance should be carried out by qualified personnel.
Avoid installing the camera in a place of high humidity.
Avoid installing the camera at a place exposed to gas or oil.
Don't point the camera directly at sunlight.
Please pay special attention to keep the unit from dropping or external shock during the process of
transportation or handling.
Never try to touch the camera with wet hands. It may cause an electric shock.
Do not expose the camera to radioactivity. It can cause a serious damage on the image sensor.
LIMITATION OF LIABILITY
This publication is provided “AS IS” without warranty of any kind, either express or implied, including but not
limited to, the implied warranties of merchantability, fitness for any particular purpose, or non-infringement of
the third party's right.
This publication could include technical inaccuracies or typographical errors. Changes are added to the
information herein, at any time, for the improvements of this publication and / or the corresponding product(s).
DISCLAIMER OF WARRANTY
In no event shall seller be liable to any party or any person, except for replacement or reasonable maintenance
of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special, consequential or
exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of the user.
(3) Unauthorized disassembly, repair or modification of the product by the user.
(4) Inconvenience or any loss when images are not displayed, due to any reason or cause
including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, when combined with third party devices.
(6) Any claim or action for damages, brought by any person or organization, due to a violation of privacy when
the surveillance footage, for some reason, becomes public or is used for the purpose other than
surveillance.

3
1. PRODUCT OVERVIEW
Key Features
2.0 megapixel progressive scan CMOS image sensor for excellent image quality
Low light, Ultra high sensitivity camera
IP66 compliant
Vandal-resistant
3-axis mechanism
Built-in temperature / humidity sensor
Heater operation according to humidity
Triple Stream for simultaneous operations
Up to 30 frames per second at all image resolutions
Integrated motion detection with pre- and post-alarm image / video buffering
Supports CBR (constant bit rate) and VBR (variable bit rate) modes
Tampering-Alarm function
Controllable frame rate
Privacy Masking up to 8 areas
Built-in PoE (power over Ethernet)
HTTPS support
DDNS and DHCP client
Specification
CLASSIFICATION
Night Vision Outdoor IR Camera
General
CPU
ARM1176JZF-STM ( 400 MHz, Instruction cache : 32kbyte,
data cache : 16kbyte, MMU )
Flash
2Gbit Flash Memory
SDRAM
2Gbit DDR3 Memory
Image Pickup
Image Sensor
2.0 Megapixel 1/2.8" SONY progressive scan CMOS image sensor
Total Pixels
1952(H) x 1116(V) 2.18 Megapixel
Effective Pixels
1944(H) x 1104(V) 2.14 Megapixel
S/N Ratio
More than 50dB
Min. Illumination
0.1Lux
Lens
3.6mm Megapixel Lens (F=0.94)
Video
Video Compression
H.264 High Profile @ Level 4.1, Motion JPEG
Resolutions
Up to 1920 x 1080
Frame rate
H.264 Up to 30fps with 1920 x 1080
H.264 Up to 30fps with VGA resolution
MJPEG Up to 30fps with VGA resolution
Video Streaming
Support Multi Stream with H.264, MJPEG
Adjustable Frame Rate
VBR / CBR in H.264
Image Setting
Brightness, Contrast, Sharpness
Auto White Balance Auto Exposure
Privacy Mask
DSS, Corridor-view (in H.264), Mirror / V-Flip, etc.
D-WDR (Low / Middle / High)
Network
Security
Password Protection
User Access Log
HTTPS Encryption
Supported Protocol
HTTP, HTTPS, DNS, RTSP, RTP, TCP, UDP, ICMP, DHCP
System
Intelligent Video
Motion detection 12 x 12 blocks

4
Integration
Alarm trigger
Motion detection
Firmware Upgrade
Remote Upgrade via Network
Physical
Memory Slot
Micro SD slot
Power Source
DC 12V, POE (Power Over Ethernet) : 802.3af
Power Consumption
4W
Net Weight
1.3lbs
LEDs
Power, Network Connection
Dimensions
4.8” (Ø ) x 3.8” (H)
Environment
Operating Temperature
14F ~ 122F
Storage Temperature
-4F ~ 140F

5
2. NAME AND FUNCTION OF EACH PART
2.1 Package Contents
APPEARANCE
DESCRIPTION
IP Camera x 1
Installation Guide x 1
Drilling Template x 1
Tapping screw (Ø 4 x 30) x 3
Plastic anchor x 3
Torx Wrench x 1
CD x 1
Junction Box
Top Rubber x 1
Junction Box x 1
Sponge x1
Tapping Screws (Ø 4 x 30) x 4
Plastic Anchor x 4
Screw PH (M4 x 12) x 4

6
2.2 Name and Function
NO.
ITEM
DESCRIPTION
Power Connector
DC12V
Caution : If camera is powered by PoE, do not
plug in DC Jack with active DC power into
DC power connector.
Network and
POE Connector
POE (Power over Ethernet) and LAN cable
Lens
3.6mm fixed lens
Micro SD
Memory card slot
1
2
3
3
2
1
4
4

7
3. INSTALLATION
3.1 Adjust Pan, Tilt and Rotation and the Viewing Angle
-Pan, Tilt, Rotate (3-Axis mechanism)
Panning axis can be adjusted 360°
Tilting axis can be adjusted 0°~ 90°
Rotating axis can be adjusted
between +180°(clockwise)
and -180°(counter-clockwise)
Do not rotate more 180°as this
might cause the internal cables to
twist and disconnect or break.
-How to adjust the Viewing Angle
a. Panning 360 degree
Turn the pan base right or
left to adjust the pan angle.
b. Tilting 90 degree
Loosen the tilt lever on the right or left side of the camera board.
Control the camera tilt angle and fasten the tilt lever again.
c. Rotation 180 degree
Grasp the front side of the camera board and turn it right or left to set the exact angle of image.
3.2 How to Mount to Ceiling
Ceiling
Ceiling Tile
Drilling template
Plastic Anchor x 3
Tapping Screw
(Ø 4 x 30) x 3
Dome Cover Ass'y
Torx Screw
(M3 x 15) x 3
Torx L-Wrench
Camera Ass'y
Safety Wire
The front side of the
camera
Tilt lever
Rotation
180°
Pan 360°
Tilt 90°
Pan base

8
①Paste a Drilling Template on the ceiling. (or wall)
②Drill screw points which will be done for installation.
Fix the plastic anchors in the holes. (in case of masonry ceiling or wall)
③Mount the camera set by using Tapping Screws with Ø 4 provided.
④Set the position and angle of the cameras to a desired direction and assemble the dome cover.
Ceiling_Junction Box
1) Attach the Sponge on Junction Box
2) Mark the hole of Junction box on the ceiling with Tapping Screw
3) Drill the hole and input the anchor. And install the Junction Box with Tapping Screw
4) Input Cable inside Junction Box
5) Install Bottom Ass'y on Junction Box with PH M4X12
6) Install Top Case Ass'y on Bottom Ass'y with L_Wrench
Ceiling Tile
Plastic Anchor x 4
Junction Base Sponge
Junction Box Assembly
Tapping Screw (Ø4x 30) x 4
Bottom Ass'y
Safety Wire
PH (M4 x 12) x 3
Top Case Ass'y
L-Wrench

9
3.3 INSTALLATION EXAMPLE
3.3.1 Installation Example
3.3.2 Connecting to the Network
Open up IP Scanner.
IP Scanner can search for the device on the local network.
Please note that only devices that are on the same subnet can be discovered.
The device is set to DHCP mode by default.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
LAN Switch Router Internet Remote Access
LocalAccess E-Mail / FTP

10
3.3.3 Accessing the Camera’s Web Setup Page
1) Open the browser and enter the camera’s IP address in the address bar or double click the device in IP
Scanner.
2) Enter the user name and password when prompted.
3) Default user name is admin and password is 1234.
4) If prompted for installation of the Active-X plug-in, allow the installation. Active-X is needed to view video
from Internet Explorer.
Enter the IP
address here

11
4. DIMENSIONS (mm)