Speco ONSIP O2D4 User manual

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
1
ONSIP O2D4

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
2
Note
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into and outlet on a circuit different from that to which the receiver is
connected
Consult the dealer or an experienced radio/TV technician for help.
Directions
Be careful not to cause any physical damage by dropping or throwing ONSIP O2D4. Especially keep the
device out of reach from children.
Do not disassemble ONSIP O2D4. No after service is assumed when disassembled.
Use only the power adapter provided with ONSIP O2D4.
Be careful to prevent moisture or water penetration into the unit. Particular attention is needed when
installing ONSIP O2D4. The screw holes for the installation screws and pipe should be maintained water
tight during the whole life time of the product.
All the electrical connection wires running into the unit should be prepared so that water from the outside
cannot flow into the unit through the surface of the wires. Penetration of the moisture through the wire for
extended period can cause malfunction of the unit or deteriorated image.

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
3
Revision History
Date
Revision
Details
May 13th, 2013
1.0
First manual revision creation.
May 24th, 2013
1.1
Text revisions
June, 19th, 2013
1.3
Updated package contents, drawings
Caution
Any changes or modifications in construction of this device which are not explicitly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
4
Contents
Contents.......................................................................................... 4
1. Introduction ................................................................................ 5
1.1. Overview................................................................................................... 5
1.2. Specification .............................................................................................. 6
1.3. Applications of ONSIP O2D4......................................................................... 8
2. Product Description ..................................................................... 9
2.1. Contents................................................................................................... 9
2.2. Product Preview ......................................................................................... 9
2.3. Physical description .................................................................................. 10
2.4. Functional Description ............................................................................... 12
3. Getting Started ......................................................................... 15
4.1. PC Requirement....................................................................................... 15
4.2. Quick Installation Guide ............................................................................. 16
4. Troubleshooting......................................................................... 22
5.1. No power is applied................................................................................... 22
5.2. Cannot connect to the Video....................................................................... 23
5.3. Windows Vista or Windows 7 ...................................................................... 24
5.4. Technical Assistance ................................................................................. 27

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
5
1. Introduction
1.1. Overview
The ONSIP O2D4 is a state-of-the-art mega-pixel, dual-codec (H.264, MJPEG) IP/network camera built with
embedded software and hardware technology. It enables real time transmission of synchronized video of up to
1080p and audio data. Remote clients can connect to ONSIP O2D4 for the real time video/audio data through
various client solutions running on PC, PDA or mobile phones. Real time 2-way communication is available
through bidirectional audio communication feature.
Designed to be a stand-alone streaming audio & video transmission device, ONSIP O2D4 can be applied to
various application area such as video security, remote video monitoring, distance education, video conference
or internet broadcasting system.
IP-66 compliant housing will extend the application area to harsh environments of wide temperature range.
Embedded PoE (Power over Ethernet, IEEE 802.3af) will enable the owner to reduce TCO (Total Cost of
Ownership) by reducing on-site wiring works for the installation.

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
6
1.2. Specification
Category
Sub-Category
Details
Video
Compression
H.264 / MJPEG
Resolution
* Refer to the datasheet.
Camera Module
Mounting Gimbal
2 Axis Gimbal
(Manual Pan/Tilt adjustment)
Audio
(Bi-directional)
Up
32 Kbps G.726
Down
64 Kbps PCM
Network
Interface
RJ-45, 10/100 Mbps, PoE (802.3af)
Access network
Static, DHCP, PPP/PPPoE
Application
RTP, RTSP, SMTP, FTP, HTTP, SDP, NTP, DNS
I/O
Sensor In
1
NC, NO Selectable
Relay Output
1
For alarm annunciation or
remote ON/OFF control (30V, 1A)
Mic/Line In
Selectable in Admin page
Line Out
1 V p-p output for amplified speaker
Power Supply
PoE
Power over Ethernet
DC Adapter
12V DC adapter (2 Amp)
Housing
IP66 compliant Vandal Proof housing
Motion Detection
3 zones
Arbitrary shape with independent sensitivity
Upgrade
Firmware upgrade over IP network
Administration
Remote administration over IP network
Client & Viewer
Web Viewer
Simple viewing over internet explorer
Speco-NVR
Standard VMS software
Dynamic IP support
DDNS support
Supported
Security
Video/Audio stream encryption
ID and Password protection

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
7
IP filtering for restricting administrative
access for audio and bi-audio
Time management
Sync to PC
Synchronize to PC
Manual
Manual time setting
Internet Time Server
Synchronize to Time Server
SDK support
Active-X
HTTP

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
8
1.3. Applications of ONSIP O2D4
Security surveillance (buildings, stores, manufacturing facilities, parking lots, banks, government facilities,
military, etc.)
Remote monitoring (hospitals, kindergartens, traffic, public areas, etc.)
Teleconference (Bi-directional audio conference). Remote Learning, Internet broadcasting
Weather and environmental observation

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
9
2. Product Description
2.1. Contents
The product package contains followings:
Contents
Description
Remarks
ONSIP O2D4
IP camera ONSIP O2D4 main unit
Tools and Mounting Screws
Screws(M4x16L 4EA, 4x16L 4EA), L-wrench
CD
Software & User’s Guide
Quick Reference Guide
Quick installation guide
2.2. Product Preview
ONSIP O2D4
IP Installer
VMS Software
(Speco NVR)
Vandal Proof (Megapixel)
Mini Dome IP Camera
PC software to allocate an IP
address to the IP Camera
PC software to view and record
the A/V streaming data transmitted
from IP camera.
(Simultaneous support of up to 64
IP cameras@D1)

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
10
2.3. Physical description
2.3.1. External View
Figure 2-1. External view of ONSIP O2D4
Figure 2-2. Connection Cable of O2D4

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
11
Figure 2-3. Adjustment knobs for the Camera
Figure 2-4. 3 axis based camera position control
(Manual adjustment of Pan, Tilt and Video rotation.)

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
12
2.4. Functional Description
DC 12V, 2A: Power input for supplying 12V DC power.
Caution: If ONSIP O2D4 is powered by PoE, do not plug in DC Jack with active DC
power into DC power connector.
MIC/LINE IN
Connect external audio source or microphone.
Line Out
Connect speakers with built in amplifier. Audio from remote site is output through Line out in bi-directional
audio mode.
100Base-T
100Mbps Ethernet connector (RJ-45) with PoE standard (802.3af). 2 LEDs on the Ethernet connector
show the status of ONSIP O2D4 as the following:
-Status LED (Dual Color - Red/Green): It will be lit in green or red depending on the status.
Green: Green color indicates that the camera is in normal operation mode. Continuous green
indicates that data transmission is possible. Blinking green means that someone is
connected to ONSIP O2D4.
Red: Continuous or blinking red indicates that hardware is in abnormal condition.
- LINK/LAN LED (Orange)
It will be lit with orange color when network cable is connected correctly. Blinking orange color indicates
normal data transmission. Off state indicates that there is trouble with the network connection.
Alarm In/Out and Audio In/Out
Used for connecting alarm sensor, alarm annunciation device, microphone and speaker to ONSIP O2D4.
Red/Green LED will be lit with red momentarily and it will be lit with green after a while when
power is applied into ONSIP O2D4

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
13
Figure 2-2 ALARM IN/OUT of ONSIP O2D4
RLY Out: Relay output is provided for connecting alarm devices or for remote on/off control of devices
such as light. Relay is normal open and it will be closed upon alarm annunciation or remote on. The relay
is capable of switching 30V AC/DC, 2A. For the application which needs power switching beyond this limit,
use additional relay switch as shown in the right of Figure 2-8.
Figure 2-3. RELAY Output connection
(left: switching requirement below 30V, 2A), (right: switching requirement higher t
han 30V, 2A. Apply this connection when either voltage or current exceed the limit.)
SENSOR IN: Connect external alarm sensor. Examples of sensing devices are infrared sensor, motion
sensor, heat/smoke sensor, magnetic sensor, etc. Connect the two wires of the sensors to
“SNS In”. The sensor type (NC/NO) can be set in admin page. Multiple sensor devices can
be connected in parallel.

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
14
Sensor
Device
Sensor
Power
Supply
NO/NCType
Sensor1-
Sensor1+
+12V GND
Sensor
Device
Sensor
Power
Supply
Open CollectorType
Photo Coupler
Figure 2-4. SENSOR input and connection of the sensor
Factory Default Switch
A switch provided for returning the IP camera to factory default state. Open the dome cover to access
the switch. Press the switch for a few seconds while power is applied.
Figure 2-5. Factory Default Switch of ONSIP O2D4
Caution: Restoring the factory default will erase all settings.

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
15
3. Getting Started
Brief information for the initial operation of ONSIP O2D4 is provided in this chapter.
4.1. PC Requirement
Audio/Video streaming data received from ONSIP O2D4 can be displayed or stored in a PC running client
programs. Minimum requirement of the PC is described below:
Minimum Requirement
Recommended Specification
CPU
Intel Core i3 3Ghz
Intel Core i7
Main Memory
2GB
4GB
Operating System*
Windows XP
Windows 7 (64bit)
Web Browser
Internet Explorer 8, 9
Internet Explorer 8, 9
Graphic Card
Video RAM 256MB
Resolution 1920x1080
Video RAM 1GB
Higher than 1920x1080
Network
100 Base-T Ethernet
100 Base-T Ethernet
* Operating Systems supported: Windows 2000 Professional, Windows XP / Vista / 7

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
16
4.2. Quick Installation Guide
1. Connect PC and ONSIP O2D4 to network.
1) Prepare a PC to run programs for the installation and video connection
(PC is needed to assign IP address to ONSIP O2D4)
2) In the case of using PoE, connect the PC and ONSIP O2D4 to the network using one of the following
ways.
If your LAN Switch does not support standard PoE, connect ONSIP O2D4 as shown in dotted line in
Figure 4-1. The DC power is applied through DC adapter.
Figure 4-1. Power and network connection
LAN switch with
standard POE
(802.3af)
LAN switch
DC adapter

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
17
2. Install Speco-NVR
Speco-NVR is a multi-channel VMS program for the IP camera. Install Speco-NVR on remote PC to connect to
these products. It is needed to assign connection information to Speco-NVR program before connection.
Insert the CD provided with product into the PC and install Speco-NVR.
Figure 4-2. Speco-NVR
Follow the sequence below for setting the IP parameter
i) Run IP installer
ii) Click (1) in ONSIP installer window.> Double click on (2) > Fill in (4) > make a selection in (5) > Fill the
parameters in (6)
iii) Click on (9) to apply the settings.
iv) You can connect to admin page by clicking on (10).
Admin Page Button
IP installer

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
18
Click on the field in (3) for sorting and rearranging the list.
Select network mode that best suits from the drop down list in (5). You can choose either
Static or ADSL and Auto (DHCP), respectively. If ADSL and Auto are selected, the fields in (6)
are deactivated.
In case of ADSL, fill the User Name and Password in (8) with the values provided by your ISP.
If DDNS service is needed, Check at the box and fill the empty field with hostname you want
in (7).
1
2
3
6
4
9
5
7
8
10

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
19
3. Remote video connection to ONSIP O2D4
1) Connection through Web Viewer
Web Viewer offers the simplest way of video connection to ONSIP O2D4. For video connection, enter
the IP address of ONSIP O2D4 in the URL window of Internet Explorer as:
Note : Active-X module should be installed on your PC before actual connection. If your PC is
not connected to the internet, you cannot download Active-X module. Most convenient way of
installing the Active-X module is installing Speco-NVR which is available from the CD or our
web site.
Figure 4-3. Web Viewer
Default ID and password of Admin Page are admin, 1234. For more detailed information, please refer to the
[Configuration_Guide] Guide.
Connection to Admin Page
Basic Control Buttons
Video Crop Control
[e.g.] Port 8080
[e.g.] Port 80
Port 80 (default) can be
omitted

O
ON NS SI IP P O O2 2D D4 4 O Ow wn ne er r’ ’s s M Ma an nu ua al l
Rev.1.3 (June,2013)
20
2) Connection through Speco-NVR
Click the camera assignment button for setting the camera address. Input the description, address,
Ch#, User ID, Password and port and then click the save button. After assignment procedure, you
must click the SAVE button. You can see the live video when you click the live view button as below.
When you exit Speco-NVR, you have to input the ID/PW, admin/1234. Details for Speco-NVR can be
found in [Speco-NVR User’s Guide].
Figure 4-4. Speco-NVR
Camera Assignment
Camera Assignment
Live view
Save
Example
Exit Program
Default ID/PW: admin/1234