Spectra Logic Spectra 64K User manual

P.N. 90910926 Revision A
Spectra 64K®Library Stability Kit
Installation Procedure

Spectra 64K Library Stability Kit Installation Procedure
2
Notices
Spectra Logic Corporation provides the unit “as is” without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties of merchantability or
fitness for a particular purpose. In no event shall Spectra Logic be liable for any loss of profits,
loss of business, loss of use or data, interruption of business, or for indirect, special, incidental,
or consequential damages of any kind, even if Spectra Logic has been advised of the possibility of
such damages arising from any defect or error.
Information furnished in this manual is believed to be accurate and reliable. However, no responsibility
is assumed by Spectra Logic for its use. Due to continuing research and development, Spectra Logic may
revise this publication from time to time without notice, and reserves the right to change any product
specification at any time without notice.
Spectra 64K Library Stability Kit Installation Procedure
Copyright © 2004 Spectra Logic Corporation. All rights reserved.
Spectra Logic Contact Information
Corporate Headquarters European Office
Address
Phone
Fax
Spectra Logic Corporation
1700 N 55th Street
Boulder CO 80301
USA
[phone] or [phone]
[phone]
Address
Phone
Fax
Spectra Logic Europe Limited
Magdalen Centre
Robert Robinson Avenue
Oxford Science Park
Oxford
UK OX44 7 RW
[phone]
[phone]
Web Site http://www.SpectraLogic.com

Spectra 64K Library Stability Kit Installation Procedure
3
Contents
Introduction ................................................................................................4
Before You Begin........................................................................................5
Prepare the Library.....................................................................................6
Lower the Leveler Feet ............................................................................... 8
Attach Brackets ...........................................................................................9
Remove the Side Panels............................................................................ 10
Finish......................................................................................................... 12

Spectra 64K Library Stability Kit Installation Procedure
4
Introduction
Caution: The stability kit is not proven to withstand natural disasters. The
stability kit only allows a Spectra 64K library to be fixed to a
data center floor.
Estimated Time Required
This procedure takes about 30 minutes.
Materials and Tools Required
You need a Stability Kit from Spectra Logic (P.N. 90911009), which includes:
• Four L-shaped brackets
• Eight 1/4-20 X 5/8 screws
• A #3 Phillips screwdriver
• Channel locks
• The library front door key
• A ladder*
*will only be necessary if the side panels must be removed.
Figure 1 The stability kit.

Spectra 64K Library Stability Kit Installation Procedure
5
Before You Begin
1. Disable any backup software that may try to access the library.
2. Switch off the power button at the rear of the library.
3. Disconnect the AC power cable.
4. Disconnect all cabling.
Note: You need access to all sides of the library to complete this
procedure.

Spectra 64K Library Stability Kit Installation Procedure
6
Prepare the Library
Note: The leveler feet on the library must be lowered, raising the library
off of its rollers.
If you cannot access the leveler feet, you must remove the side
panels. Proceed to Remove the Side Panels on page 10.
Remove the Front and Rear Kick Plates
1. Both the front and rear kick plates snap in and out of place; no tools are required to
remove them.
Locate the front kick plate and pull it off (Figure 2).
Figure 2 Remove the front kick plate.

Spectra 64K Library Stability Kit Installation Procedure
7
2. Locate the rear kick plate and pull it off (Figure 3).
3. Set aside both kick plates for later replacement.
Figure 3 Remove the rear kick plate.

Spectra 64K Library Stability Kit Installation Procedure
8
Lower the Leveler Feet
Warning: For optimum safety, it is best to lower the leveler feet
simultaneously with another person. This prevents the library
from tipping over.
Caution: Once the leveler feet are lowered, the library is no longer
mobile. Ensure that the library is in the desired location before
lowering the leveler feet.
1. Lower the front leveler feet (Figure 4).
Note: It may be necessary to remove the rubber portion of the leveler
feet to adequately grip the bolt head.
Note: The leveler feet must be lowered enough to raise the library off of
its rollers. The distance the levelers need to be lowered may vary
depending on the level of the data center floor.
2. Lower the rear leveler feet.
Figure 4 Lower the leveler feet.

Spectra 64K Library Stability Kit Installation Procedure
9
Attach Brackets
1. Use a #3 Phillips screwdriver and four of the screws provided to attach two
brackets to the front of the library (Figure 5).
2. Use a #3 Phillips screwdriver and the remaining four screws provided to attach two
brackets to the rear of the library.
3. Proceed to Finish on page 12.
Figure 5 Attach front brackets.

Spectra 64K Library Stability Kit Installation Procedure
10
Remove the Side Panels
Note: You only need to remove the side panels if you cannot access the
leveler feet. Otherwise proceed to Finish on page 12.
1. Remove the library hood by lifting upward on the front of the library. No tools are
required to remove the hood (Figure 6).
Note: A ladder may be required to access the top of the library.
o
Figure 6 Remove the library hood.