Spectra IB965F User manual

IB965F
3rd Gen. Intel®CoreTM i7/i5/i3
+ PCH
PICMG 1.3 SHB Express Full-Size CPU Card
USER’S MANUAL
Version 1.0

ii IB965 User’s Manual
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® Sandy Bridge DC/QC Processor are registered
trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.

IB965 User’s Manual iii
Table of Contents
Introduction...................................................... 1
Product Description............................................................1
Checklist.............................................................................2
IB965F Specifications........................................................3
Board Dimensions..............................................................5
Installations...................................................... 6
Installing the CPU ..............................................................7
Installing the Memory.........................................................8
Setting the Jumpers.............................................................9
Connectors on IB965F......................................................14
BIOS Setup.......................................................25
Drivers Installation......................................51
Intel Chipset Software Installation Utility.........................52
VGA Drivers Installation..................................................55
Realtek HD Audio Driver Installation ..............................58
LAN Drivers Installation..................................................60
Intel® Management Engine Interface ...............................64
Intel® USB 3.0 Drivers....................................................67
Appendix...........................................................71
A. I/O Port Address Map..................................................71
B. Interrupt Request Lines (IRQ)......................................72
C. Watchdog Timer Configuration...................................73

iv IB965 User’s Manual
This page is intentionally left blank.

INTRODUCTION
IB965 User’s Manual 1
Introduction
Product Description
The IB965F PICMG 1.3 SHB Express fullsize CPU Card is based on the
latest Intel®BD82B75 chipset. The platform supports 3rd Generation
Intel®Core i7/i5/i3 with LGA1155 packing and features an integrated
dual-channel DDR3 memory controller as well as a graphics core (4000).
Display interfaces of the CPU card include VGACRT, DVI-D and 24-bit
dual channel LVDS. The edge connectors are for VGACRT, USB 2.0,
USB 3.0 and dual Gigabit LAN RJ45 connectors. One SATAIII port and
three SATA II ports are available. Expansion slot is provided with a Mini
PCIe socket on the component side. Four serial ports and a parallel port
are supported.
Dimensions of the board are 338mm x 126mm.
IB965F FEATURES:
Supports Intel®3rd Generation Core i7/i5/i3 DT processors
Two DDR3 DIMM, 1066/1333/1600MHz, Max. 16GB
Dual Intel®PCI-Express Gigabit LAN
Integrated Graphics for CRT, DVI-D, LVDS displays
3x SATA 2.0, 1x SATA III, 3x USB 2.0, 3x USB 3.0
4x COM, 1x parallel port
Mini PCIe socket, iSMART, Watchdog timer, Digital I/O
2x SATA 2.0, 4x USB 2.0 for PICMG 1.3 backplane
1x PCI-E (x16), 1x PCI-E (x4), 4x PCI for PICMG 1.3
backplane

INTRODUCTION
2 IB965 User’s Manual
Checklist
Your IB965F package should include the items listed below.
The IB965F PICMG 1.3 SHB Express Full-Size CPU Card
This User’s Manual
1 CD containing chipset drivers and flash memory utility

INTRODUCTION
IB965 User’s Manual 3
IB965F Specifications
Product Name
IB965F (B75)
IB965RF(Q77)
Form Factor
PICMG 1.3 SHB Express Full size CPU card
CPU Type
- 3rd Generation Intel®CoreTM i7/i5/i3 DT processor
- FCLGA1155 package [37.5 mm x 37.5mm]
- TDP: QC= 77W/65W ; DC=45W/35W
CPU Speed
2.3GHz ~ 3.4GHz (TDP=35W~77W)
BIOS
AMI BIOS, support ACPI Function
CPU Socket
LGA1155
Chipset
Intel®BD82B75 PCH [IB965F]
Intel®BD82Q77 PCH [IB965RF]
27mm x 27mm, FCBGA942 (TDP=6.7W)
Memory
3rd Generation Intel®CoreTM i7/i5/i3 DT processor integrated memory
controller, support DDR3-1333/1600 MHz (Non-ECC)
- DIMM x 2, Max. 16GB
VGA / LVDS
3rd Generation Intel®CoreTM i7/i5/i3 DT processor integrated graphics
device
- VGA
- LVDS (Chrontel CH7511 via DP, support 24-bit dual channel)
- DVI-D: via level-shifter ASM1442
LAN
1. Intel®82579V GbE PHY x1
2. Intel®82583V PCI-e Gigabit LAN controller x1
** There is no LAN signal to the backplane**
USB
Intel®BD82B75/Q77 PCH integrated USB 2.0 host controller
- 2ports thru onboard pin-header
- 1port @ rear panel I/O
- 1port via MiniPCIe @ component side
Intel®BD82B75/Q77 PCH integrated USB 3.0 host controller
- 1port @ rear panel I/O
2ports via onboard box header [ 2*10 pins box header, Blue color]
6 ports on SHB, 4 ports to the backplane [Connector C]
Serial ATA Ports
Intel®BD82B75/Q77 PCH built-in SATA controller, supports total 6
ports
1 x SATAIII + 3 x SATAII (one SATA II shared with mSATA)[IB965F]
2 x SATAIII + 2 x SATAII (one SATA II shared with mSATA)[IB965RF]
[2 x SATA 2.0 ports to the backplane Connector C]
Audio
Intel®BD82B75/Q77 PCH built-in high definition audio w/ Realtek
ALC662 Codec support 5.1 channel
LPC I/O
Fintek F81866AD-I (128-pin LQFP [14mm x 14 mm])
- COM1 (RS232/422/485), jumper-less design (SP339)
- COM2/COM3/COM4 (RS232),
- Hardware monitoring (2 thermal inputs,4 voltage monitor inputs & 2
Fan headers, one PWM fan type = 4-pin for CPU FAN; one DC fan
type = 3-pin for SYS FAN)
- Support Parallel port
Digital IO
4 in & 4 out
Keyboard/Mouse
Connector
Supports PS/2 Keyboard/Mouse thru onboard pin-header
Expansion Slots
Mini PCIe socket x1@ component side [Full-sized]
Support USB client & mSATA[share with onboard SATA]

INTRODUCTION
4 IB965 User’s Manual
Edge Connector
(The same as
IB970)
DB15 x1 for VGA
RJ45 x 2 for LAN 1 & 2
USB 2.0 x 1
USB 3.0 x 1
Onboard
Header/Connector
DF11-20 pins pin-header x1 for DVI-D
DF13-20 pins pin-header x 2 for 24-bit dual channel LVDS( **
brightness control not supported**)
2x13 pins box-header x1 for Printer port
DF11-20 pins box-header x1 for COM1/2
DF11-20 pins box-header x1 for COM3/4
2x5 pins pin-header x1for USB 2.0 x2
2x6 pins pin-header x1 for Audio (Line-Out, Line-In & Mic)
2 x 5 pins pin-header x 1 for Digital I/O
2 x 4 pins pin-header x 1 for PS/2 KB/MS
4 pins pin-header x1 for CPU fan (PWM smart fan)
3 pins pin-header x1 for system fan
SATA x4 (Black connectors for SATA2; Blue connectors for SATA 3)
2X10 pins pin-header x 1 for front panel indicators
2 x 2 pin ATX power connector x 1
Interface
1x PCIe(16x) [Connector A & B]
4x PCIe(1x) or 1x PCIe(4x) [Connector A]
4x PCI masters [Connector D]
Watchdog Timer
Yes (256 segments, 0, 1, 2…255 sec/min)
Others
- RAID function (0, 1, 5, 10) [IB965RF only]
- iSMART{Thru MCU for supporting auto scheduler & Power
resume}
- LAN wake up
- TPM 1.2 supported
- Reserved extra mounting hole as IB970
System Voltage
+5V, +3.3V, +12V, -12V & 5VSB
RoHS
Yes
Board Size
338mm x 126mm

INTRODUCTION
IB965 User’s Manual 5
[
Board Dimensions

INSTALLATIONS
6 IB965 User’s Manual
Installations
This section provides information on how to use the jumpers and
connectors on the IB965F in order to set up a workable system. The
topics covered are:
Installing the CPU................................................................................ 7
Installing the Memory.......................................................................... 8
Setting the Jumpers.............................................................................. 9
Connectors on IB965F....................................................................... 14

INSTALLATIONS
IB965 User’s Manual 7
Installing the CPU
The IB965F board supports an LGA1155 Socket (shown below) for Intel
Sandy Bridge processors.
To install the CPU, unlock first the socket bypressing the lever sideways,
then lift it up to a 90-degree. Then, position the CPU above the socket
such that the CPU corner aligns with the gold triangle matching the
socket corner with a small triangle. Carefully insert the CPU into the
socket and push down the lever to secure the CPU. Then, install the heat
sink and fan.
NOTE:
Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.

INSTALLATIONS
8 IB965 User’s Manual
Installing the Memory
The IB965F board supports two DDR3 memory socket for a maximum
total memory of 16GB in DDR3 DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
DDR3 Module
Lock
Lock
Lock
Lock

INSTALLATIONS
IB965 User’s Manual 9
Setting the Jumpers
Jumpers are used on IB965F to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB965F and their respective functions.
JP1: COM1 RS232 RI/+5V/+12V Power Setting...............................10
JP2: COM2 RS232 RI/+5V/+12V Power Setting...............................10
JP3: Power On Type..........................................................................10
JP7: Flash Descriptor Security Override (Factory use only)................11
JP10: LVDS Panel Power Selection...................................................11
JP11: LVDS EEPROM Flash Connector (factory use only)................11
JP12: BL_ADJ_LEVEL Setting.........................................................12
JP13: BL Voltage Setting ..................................................................12
JBAT1: Clear CMOS Contents..........................................................12
SW1: LVDS Panel Type Setting ........................................................13

INSTALLATIONS
10 IB965 User’s Manual
JP1: COM1 RS232 RI/+5V/+12V Power Setting
JP1
Setting
Function
Pin 1-3
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 3-5
Short/Closed
+5V
JP2: COM2 RS232 RI/+5V/+12V Power Setting
JP2
Setting
Function
Pin 1-3
Short/Closed
+12V
Pin 3-4
Short/Closed
RI
Pin 3-5
Short/Closed
+5V
JP3: Power On Type
JP3
Function
Open
ATX Mode
(Default)
Close
AT Mode

INSTALLATIONS
IB965 User’s Manual 11
JP7: Flash Descriptor Security Override (Factory use only)
JP7
Flash Descriptor Security
Override
Open
Disabled
(Default)
Close
Enabled
JP10: LVDS Panel Power Selection
JP10
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
JP11: LVDS EEPROM Flash Connector (factory use only)

INSTALLATIONS
12 IB965 User’s Manual
JP12: BL_ADJ_LEVEL Setting
JP12
Function
Open
3.3V
Close
5V (default)
JP13: BL Voltage Setting
JP13
Setting
Function
Pin 1-2
Short/Closed
+3.3V
Pin 3-4
Short/Closed
+5V
Pin 5-6
Short/Closed
+12V(Default)
JBAT1: Clear CMOS Contents
JBAT1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS

INSTALLATIONS
IB965 User’s Manual 13
SW1: LVDS Panel Type Setting
SW1-4
SW1-3
SW1-2
SW1-1
Panel Type
ON
ON
ON
ON
800*600 18bit 1ch
ON
ON
ON
OFF
1024*768 18bit 1ch
ON
ON
OFF
ON
1024*768 24bit 1ch
ON
ON
OFF
OFF
1280*768 18bit 1ch
ON
OFF
ON
ON
1280*800 18bit 1ch
ON
OFF
ON
OFF
1280*960 18bit 1ch
ON
OFF
OFF
ON
1280*1024 24bit 2ch
ON
OFF
OFF
OFF
1366*768 18bit 1ch
OFF
ON
ON
ON
1366*768 24bit 1ch
OFF
ON
ON
OFF
1440*900 24bit 2ch
OFF
ON
OFF
ON
1440*1050 24bit 2ch
OFF
ON
OFF
OFF
1600*900 24bit 2ch
OFF
OFF
ON
ON
1680*1050 24bit 2ch
OFF
OFF
ON
OFF
1600*1200 24bit 2ch
OFF
OFF
OFF
ON
1920*1080 24bit 2ch
OFF
OFF
OFF
OFF
1920*1200 24bit 2ch

INSTALLATIONS
14 IB965 User’s Manual
Connectors on IB965F
Connector Locations on IB965F........................................................ 15
CN1, CN2, CN4: SATA2 Connectors................................................ 16
CN3: SATA3 Connectors.................................................................. 16
CN1: SATA3 Connectors (IB965RF only)......................................... 16
CN5: DB-15 VGA Connector............................................................ 16
CN6: USB3.0/2.0 Connector............................................................. 17
CN7: USB2.0 Connector................................................................... 17
CN8: Gigabit LAN (Intel 82579V) Connector ................................... 17
CN9: Gigabit LAN (Intel 82583V) Connector ................................... 17
CN10: LCD Backlight Connector ...................................................... 17
CN11: USB3.0 Connector................................................................. 17
J1: COM3, COM4 Serial Port (DF11 Connector) .............................. 18
J2: COM1, COM2 Serial Port (DF11 Connector) .............................. 18
J3: Front Panel Function Connector................................................... 19
J4, J5: DDR3 DIMM Socket ............................................................. 19
J6: External Audio Connector (DF11 Connector) .............................. 19
J7: ATX 12V Power Connector......................................................... 20
J8: Digital I/O 4 In/4 Out................................................................... 20
J9: PS/2 Keyboard and Mouse Connectors (DF11 Connector) ........... 20
J10: SPI Flash Connector (Factory use only)...................................... 21
J11: Parallel Port ............................................................................... 21
J12: USB2.0 Connectors ................................................................... 22
J13: DVI-D Port (DF11 Connector) .................................................. 22
J19: MCU Flash Connector (factory use only).................................... 22
J20: Mini PCIE Connector (Support M-SATA with CN4) ................. 23
CPU_FAN1: CPU Fan Power Connector........................................... 23
SYS_FAN1: System Fan1 Power Connector...................................... 23
CH1, CH2: LVDS Connectors........................................................... 24

INSTALLATIONS
IB965 User’s Manual 15
Connector Locations on IB965F

INSTALLATIONS
16 IB965 User’s Manual
CN1, CN2, CN4: SATA2 Connectors
CN3: SATA3 Connectors
CN1: SATA3 Connectors (IB965RF only)
CN5: DB-15 VGA Connector
Signal Name
Pin #
Pin #
Signal Name
Red
1
2
Green
Blue
3
4
N.C.
GND
5
6
GND
GND
7
8
GND
VCC
9
10
GND
N.C.
11
12
DDCDATA
HSYNC
13
14
VSYNC
DDCCLK
15