Spectra 1725 User manual

REFERENCE & INSTALLATION MANUAL
SPECTRA CONTROL PANELS V1.2
1725, 1725EX, 1728 AND 1728EX 1758 AND 1758EX

TABLE OF CONTENTS
INTRODUCTION ....................................................................................................................................4
Features .......................................................................................................................................................................4
Specifications ...............................................................................................................................................................4
Detectors, Keypads and Expansion Modules ...............................................................................................................5
INSTALLATION ......................................................................................................................................7
Location and Mounting .................................................................................................................................................7
Earth Ground ................................................................................................................................................................8
AC Power .....................................................................................................................................................................8
Back up Battery ............................................................................................................................................................9
Auxiliary Power Terminals ............................................................................................................................................9
Telephone Line Connection .........................................................................................................................................9
Bell Output Connection ................................................................................................................................................9
Programmable Output Connections ...........................................................................................................................10
Alarm Relay ................................................................................................................................................................10
Keyswitch Connections ..............................................................................................................................................10
Keypad Installation .....................................................................................................................................................10
Keypad Zone Connections .........................................................................................................................................10
Single Zone Inputs .....................................................................................................................................................11
Double Zone Inputs (with ATZ Option only) ...............................................................................................................12
Fire Circuits ................................................................................................................................................................12
Connecting a Liberator SPC-319 Wireless Module ....................................................................................................13
Connecting a Zone Expansion Module (SPC-ZX4/ZX8) ............................................................................................13
PROGRAMMING METHODS .................................................................................................................15
Winload Software for Windows ..................................................................................................................................15
Programming Using a Keypad ...................................................................................................................................15
Programming Using A Paradox Memory Key .............................................................................................................16
ACCESS CODES ...................................................................................................................................17
Access Code Length ..................................................................................................................................................17
Installer Code (Default: 000000) ................................................................................................................................17
System Master Code (Default: 123456) .....................................................................................................................17
User Code Options .....................................................................................................................................................17
Lock Master Code ......................................................................................................................................................19
Duress Code ..............................................................................................................................................................19
ZONE PROGRAMMING ........................................................................................................................20
Zone Definitions .........................................................................................................................................................21
Zone Partition Assignment .........................................................................................................................................23
Zone Options ..............................................................................................................................................................23
Zone Speed ................................................................................................................................................................25
EOL Zones .................................................................................................................................................................25
ATZ - Zone Doubling (Optional) .................................................................................................................................25
ARMING AND DISARMING OPTIONS ..................................................................................................26
Switch To Stay Arming ...............................................................................................................................................26
Auto Force Arming .....................................................................................................................................................26
Restrict Arming On Battery Fail ..................................................................................................................................26
Restrict Arming On Tamper Failure ............................................................................................................................26
Timed Auto-Arming ....................................................................................................................................................26
No Movement Auto-Arming ........................................................................................................................................27
Auto-Arming Options ..................................................................................................................................................27
One-Touch Arming .....................................................................................................................................................27
Exit Delay ...................................................................................................................................................................27
Bell Squawk On Arm/Disarm With Keypad .................................................................................................................28
Bell Squawk On Arm/disarm with Remote Control .....................................................................................................28

2REFERENCE & INSTALLATION MANUAL
No Exit Delay When Arming with Remote Control .....................................................................................................28
No Exit Delay Beeps and No Bell Squawk When Stay Arming ..................................................................................28
ALARM OPTIONS ................................................................................................................................29
Bell Cut-Off Timer .......................................................................................................................................................29
Recycle Alarm ............................................................................................................................................................29
Tamper Recognition ...................................................................................................................................................29
Keypad Panic Options ................................................................................................................................................30
REPORTING AND DIALER SETTINGS .................................................................................................31
Reporting/Dialer (Enable/Disable) ..............................................................................................................................32
Report Codes .............................................................................................................................................................32
Central Station Telephone Numbers ..........................................................................................................................34
Partition Account Numbers .........................................................................................................................................35
Reporting Formats ......................................................................................................................................................35
Event Call Direction ....................................................................................................................................................36
Dialing Method ...........................................................................................................................................................36
Pulse Ratio .................................................................................................................................................................36
Bell on Communication Failure ..................................................................................................................................37
Dial Tone Delay ..........................................................................................................................................................37
Maximum Dialing Attempts .........................................................................................................................................37
Delay Between Dialing Attempts ................................................................................................................................37
Alternate Dial Option ..................................................................................................................................................37
Recent Close Delay ....................................................................................................................................................37
Auto Test Report ........................................................................................................................................................37
Power Failure Report Delay .......................................................................................................................................37
Disarm Reporting Options ..........................................................................................................................................38
Zone Restore Report Options ....................................................................................................................................38
Pager Delay ................................................................................................................................................................38
Telephone Line Monitoring (TLM) ..............................................................................................................................38
PROGRAMMABLE OUTPUTS ..............................................................................................................39
PGM Activation Event ................................................................................................................................................39
PGM De-Activation Event ...........................................................................................................................................39
PGM Delay .................................................................................................................................................................40
PGM Type ..................................................................................................................................................................40
PGM2 Strobe Options (1758 & 1758EX Only) ...........................................................................................................40
Alarm Relay Options (1758 & 1758EX Only) ..............................................................................................................40
SYSTEM SETTINGS .............................................................................................................................41
Hardware Reset .........................................................................................................................................................41
Installer Lock ..............................................................................................................................................................41
Battery Charge Current ..............................................................................................................................................41
Partitioning .................................................................................................................................................................41
System Real-Time Clock ............................................................................................................................................41
Clock Adjust ...............................................................................................................................................................41
Keypad Tamper Supervision ......................................................................................................................................42
Keypad Audible Trouble Warning ...............................................................................................................................42
Installer Quick Functions Keys ...................................................................................................................................42
Zone Expansion Module Supervision .........................................................................................................................43
Liberator Wireless Bus Module Supervision ...............................................................................................................43
Wireless Transmitter Low Battery Supervision ...........................................................................................................43
Wireless Transmitter Supervision Options .................................................................................................................43
ReProgram All Expansion Modules ............................................................................................................................44
SETTINGS FOR WINLOAD SOFTWARE ...............................................................................................45
Panel Answer Options ................................................................................................................................................45
Panel Identifier ...........................................................................................................................................................45
PC Password ..............................................................................................................................................................45
PC Telephone Number ...............................................................................................................................................45

SPECTRA SERIES 3
Call WinLoad Software ...............................................................................................................................................45
Answer WinLoad Software .........................................................................................................................................46
Auto Event Buffer Transmission .................................................................................................................................46
Call Back Feature .......................................................................................................................................................46
LIBERATOR MODULE ..........................................................................................................................47
Wireless Transmitter Assignment (Liberator) .............................................................................................................47
Supervision Options (Liberator) ..................................................................................................................................47
On-Board Tamper Recognition (Liberator) .................................................................................................................48
PGM Activation event (Liberator) ................................................................................................................................48
PGM De-Activation Event (Liberator) .........................................................................................................................48
PGM Delay (Liberator) ................................................................................................................................................48
PGM Follows Global PGM (Liberator) ........................................................................................................................49
Serial Number Display (Liberator) ..............................................................................................................................49
Signal Strength Display (Liberator) .............................................................................................................................49
Reset Liberator Module ..............................................................................................................................................49
ZONE EXPANSION MODULE ...............................................................................................................50
Zone Input Assignment (Zone Module) ......................................................................................................................50
EOL Zones (Zone Module) .........................................................................................................................................50
Tamper Recognition (Zone Module) ...........................................................................................................................50
PGM Activation Event (Zone Module) ........................................................................................................................51
PGM De-Activation Event (Zone Module) ...................................................................................................................51
PGM Delay (Zone Module) .........................................................................................................................................51
PGM Follows Global PGM (Zone Module) .................................................................................................................51
Reset Zone Expansion Module ...................................................................................................................................51
REMOTE CONTROL PROGRAMMING ..................................................................................................52
User Assignment ........................................................................................................................................................52
Button Programming ...................................................................................................................................................52
Remote Control Assignment (Liberator Only) .............................................................................................................53
Remote Control Assignment (1758 and 1758EX Only) ..............................................................................................53
USER OPERATION .............................................................................................................................54
Trouble Display ...........................................................................................................................................................54
Partitioning ..................................................................................................................................................................55
Programming Access Codes ......................................................................................................................................55
Disarming & Deactivating an Alarm ............................................................................................................................55
Regular Arming ...........................................................................................................................................................56
Stay Arming ................................................................................................................................................................56
Instant Arming .............................................................................................................................................................56
Force Arming ..............................................................................................................................................................57
Manual Bypass Programming .....................................................................................................................................57
One-Touch Arming .....................................................................................................................................................57
Keyswitch Arming .......................................................................................................................................................58
Panic Alarms ...............................................................................................................................................................58
Auto-Arming ................................................................................................................................................................58
Alarm Memory Display ................................................................................................................................................58
Programming Chime Zones ........................................................................................................................................59
Keypad Muting ............................................................................................................................................................59
INDEX ..................................................................................................................................................62

4REFERENCE & INSTALLATION MANUAL
PART 1: INTRODUCTION
1.1 FEATURES
• Up to 16 fully programmable zones:
1725EX: 4 zones [8 zones with ATZ (1725 only)] + 2 keypad zones, can expand to 16 zones
1728EX or 1758EX:5 zones [10 zones with ATZ (1728/1758 only)] + 2 keypad zones, can expand to 16 zones
• Up to 8 remote controls built-in with 1758 and 1758EX only.
• Two completely independent partitions. Many of the features and options in the Spectra System can be inde-
pendently set for each partition such as event reporting, entry/exit delay, auto-arming and many more. All zones,
the keyswitch and all user codes are assigned to specific partitions, making this a true partitioned system.
• Communication bus facilitates the addition,programming and monitoring of wireless and/or hardwire expansion modules.
• 1 Installer Code and 48 User Codes (including: 1 System Master, 2 Masters, and 1 Duress)
• One or more fully programmable outputs (PGMs).
• Simple, direct and logical programming
• Event Call Direction: The Spectra Series Control Panel events are divided into 5 groups of events. Each of these
event groups can be programmed with a separate dialing sequence.
• Two 32-digit Central Station Telephone Numbers and one 32-digit Back-up Telephone Number
• Contact ID, Pager Format and many more High-Speed Communication Formats
• "False Alarm Prevention" features such as: Intellizone, Auto Zone Shutdown, Beep on Exit Delay, Programmable
Delay Before Alarm Transmission, and Recent Closing Report
• Regular Arming, Stay Arming, Instant Arming, Force Arming, One-Touch Arming, Auto-Arming, or Arming with
Keyswitch
• 256 Event Buffer with time stamp
• Optional 5A Alarm Relay (1758 and 1758EX only)
• Telephone Line Supervision
• Keypad activated panic alarms
• Compatible with Winload software for Windows®
• And much, much, more…
1.2 SPECIFICATIONS
1.2.1 SPECTRA CONTROL PANEL
• AC Power: 16VAC transformer with minimum 20VA rating (Rec.: 40VA), 50-60Hz
(UL tested to 60Hz only)
• Battery: 12VDC, 4Ah
• Aux. Power: 600mA typical, 700mA maximum, fuseless shutdown @ 1.1A
• Bell Output: 1A, fuseless shutdown @ 3A (1725/EX and 1728/EX) or 2.5A (1758/EX)
• PGM1 Output: 150mA
• PGM2 Output: 2.5A (1758/EX only)
1.2.2 SPC-319 LIBERATOR WIRELESS MODULE
• Power input: 9-16VDC
• Current Consumption:70mA
• Frequency Hopping: @ 902MHz - 928MHz or 868MHz
• Range of Detectors & Contact Switches: 1000m (3280’) or 300m (984’) for 868 MHz
Range of Remote Controls: 30m (100‘)
• Data Rate:10 KB/s
• Sensitivity:-105dBm
• Dimensions (without antenna): 15cm H x 16cm L x 3cm W (6”H x 6.5”L x 1.1”W)
• Operating Temperature: 0°C to 50°C (32°F to 122°F)
• Operating Humidity: 85%
• PGM Outputs:1 + 1(optional)
• PGM Output current: 5A relay
1.2.3 HAND-HELD REMOTE CONTROLS
• Water Resistant
• Range: 30m (100ft.)
• Battery: Lithium 3V (CR2032)

SPECTRA SERIES 5
• Battery Life: Approx. 1 to 2 years
• Power Transmission: 0.25mW
• Current Consumption: 18mA (transmission)
1.2.4 SPC-ZX4 OR ZX8 HARDWIRE EXPANSION MODULE
• Power input: 9-16VDC
• Current Consumption: 28mA
• Speed operation:16MHz
• PGM Outputs:1 (ZX8 only)
• PGM Output current: 50mA (ZX8 only)
• Number of inputs/zones: SPC-ZX4 = 4, ZX8 = 8
• Proper operation: Red LED flash (ZX8 only)
• Trouble indication: Red LED toggle on/off at 1 sec. intervals (ZX8 only)
• Humidity: 95% maximum
1.2.5 SPECTRA KEYPADS (1686H, 1686V, 1689 & 1641)
• Power input:9-16VDC,
• Operation Speed:16MHz
• 1 standard keypad zone
• On-board Tamper Switch (optional)
1686H & 1686V 10-Zone LED Keypad
• Current Consumption: 62 to 116mA
1689 16-Zone LED Keypad
• Current Consumption: 50 to 117mA
1641 32 Character LCD Keypad
• Current Consumption: 60 to 80mA
• PGM: 1 with 50mA current limit
• LCD: Super Twisted Nematic display (STN), Wide viewing angle, Backlight & Contrast adjustable
1.3 DETECTORS, KEYPADS AND EXPANSION MODULES
If you would like to obtain more information on our line of keypads, security system accessories or other security
products, please contact your local Paradox distributor or visit our web site at http://www.paradox.ca.
1.3.1 SPECTRA 1686H AND 1686V 10-ZONE LED KEYPADS
The elegant Spectra 1686H/1686V LED keypads’ patented
“key-light” feature, provides a user-friendly display of the
system’s current status. For example, if zone 5 is open, the [5]
key turns on. What could be simpler? Designed to be
compatible with any Spectra Series control panel, our Euro-
Style Spectra keypads eliminate stocking and ordering
concerns.
1.3.2 SPECTRA 1689 16-ZONE LED KEYPADS
The Spectra 1689 LED keypad’s brilliant display provides
instant feedback of the system’s current status. Designed to be
compatible with any Spectra Series control panel, this
ergonomic and user-friendly keypad will complete any
installation.

6REFERENCE & INSTALLATION MANUAL
1.3.3 SPECTRA 1641 LCD KEYPAD
The 1641 is a 32-character programmable LCD keypad which
includes a zone input as well as a PGM output. View zone,
event and trouble status for one or more partitions, display
entry/exit delay, adjust contrast, backlight, and many other
features. Most messages in the LCD keypad are
programmable.
1.3.4 LIBERATOR SPC-319 WIRELESS BUS MODULE
Connected to the Spectra control panel’s communication bus,
the fully supervised Liberator Wireless Bus Module (SPC-319)
allows you to add up to eight fully programmable remote
controls and up to eight Liberator Wireless Detectors and
Contact Switches (door contacts). The SPC-319 also provides
one programmable 5A relay (PGM). A second 5A
programmable relay (PGM) is available as an option.
1.3.5 ZONE EXPANSION MODULES
Connected to the Spectra control panel’s
communication bus, the fully supervised Zone
Expansion Modules provide you with up to 4 (SPC-ZX4)
or up to eight (ZX8) additional hardwired inputs and one
normally open 50mA PGM output (ZX8 only).
1.3.6 PARAVOXTM - VOICE DIALER
In areas where security system monitoring is not available, let
the sophisticated Paravox voice dialer take over. Compatible
with any control panel, the Paravox will verbally report system
status by phone, advising of detection of burglary, fire, flood or
any other situation programmed to generate a report condition.
Fully programmable over the telephone (no external keypad
required), the Paravox guides the end user through all system
functions with a full set of voice prompts. All the user needs to
remember is their P.I.N. The “key ahead” feature eliminates the
frustration and time wasted for experienced operators, by
allowing them to key in selections before a prompt ends.
1.3.7 DIGITAL DETECTORS
The Paradox DigigardTM (25/50/60/70) digital motion detectors
can immediately identify the signal produced by a moving
human body and will not be triggered by any other occurrences
in the protected area. False alarms are virtually eliminated.
Using 100% digital detection technology and smart digital
processing software leaves no room for error.
With the Digigard 70, animal lovers can maximize their security
protection. Thanks to the unique design of the patent-pending
Digigard “pet friendly” lens and dual “decision” optics, the
Digigard 70 double-checks every movement signal.
Take all that’s good about infrared digital detection, add to that an advanced microwave “supervisor”, and
you have Digital Vision motion detectors. Once the Vision’s digital infrared detector identifies an intruder,
its microwave sensor must confirm the presence of movement before an alarm is triggered.
We also have number or reliable analog detectors available.

SPECTRA SERIES 7
PART 2: INSTALLATION
2.1 LOCATION AND MOUNTING
Before mounting the cabinet, push the five white nylon-mounting studs into the back of the cabinet. Pull all cables
into the cabinet and prepare them for connection before mounting the circuit board into the back of the cabinet.
Select an installation site that isn't easily accessible to intruders and leave at least 2" around the panel box to permit
adequate ventilation and heat dissipation. The installation site should be dry and close to an AC source, ground
connection and telephone line connection.
Figure 2-1A: Spectra 1725, 1725EX, 1728 and 1728EX Control Panel Overview

8REFERENCE & INSTALLATION MANUAL
2.2 EARTH GROUND
Connect the zone and dialer ground terminals from the control panel to the cabinet and cold water pipe or grounding
rod as per local electrical codes.
For maximum lightning protection, use separate earth grounds for the zone and dialer grounds as
shown in Figure 2-1A.
2.3 AC POWER
Do not use any switch-controlled outlets to power the transformer. Connect the transformer as shown in Figure 2-
1A. Use Table 1 to determine the required transformer.
Table 1: Transformer Requirements Table
Transformer: Min. 16VAC 20VA
UL: Amseco XP-1620 Rec. 16VAC 40VA UL: Amseco XP-1640
Spectra DC Power Supply rated at: 1.2A 1.5A
Auxiliary Supply can provide a maximum of: typ: 600mA, max: 700mA typ: 600mA, max: 700mA
Acceptable Battery Charge Currents (seepage 41) 350mA 350mA/700mA
Figure 2-1B: Spectra 1758 and 1758EX Control Panel Overview
Other than the location of the parts on the board and the items that have been indicated below, connections to these
control panels are identical to those on page 7.

SPECTRA SERIES 9
2.4 BACK UP BATTERY
In order toprovide power during a power loss, connect a 12VDC 4Ahrechargeable acid/lead or gel cell backupbattery as
shown in Figure 2-1A. Connect the backup battery after applying AC power. When installing verify proper polarity, as
reversed connections will blow the battery fuse. Also, refer to BatteryCharge Current on page 41.
2.4.1 BATTERY TEST
If the battery is disconnected a "No/Low Battery" failure will appear in the keypads’ Trouble Display (see
page 54). This trouble will also appear if the battery’s capacity is too low or if the voltage drops to 10.5 volts
or lower while the control panel is running on the back up battery. At 8.5 volts or lower, the panel shuts
down and all outputs close.
2.5 AUXILIARY POWER TERMINALS
The auxiliary power supply terminals can be used to power motion detectors, keypads and other modules or
accessories in the security system. A fuseless circuit protects the power supply against current overload and
automatically shuts down if the current exceeds 1.1A. If this occurs the “Maximum Auxiliary Current” failure will appear
in the keypads’ Trouble Display (see page 54). Therefore, the combined current consumption of devices connected to
the auxiliary power supply should not exceed 700mA. If the auxiliary output is overloaded and is shut down, you must
disconnect all loads from the output for at least 10 seconds before reconnecting any load back to the auxiliary output.
2.6 TELEPHONE LINE CONNECTION
In order to report system events to the central station you must connect the incoming telephone company wires into
the TIP and RING connections of the control panel. Then run the wires from T1 and R1 to the telephone or
telephone system as shown in Figure 2-1A.
2.7 BELL OUTPUT CONNECTION
The BELL+ and BELL- terminals power bells, sirens and other warning devices requiring a steady voltage output
during an alarm. The bell output supplies 12VDC upon alarm and can support two 20-watt sirens or one 30-watt
siren. The bell output uses a fuseless circuit and will automatically shut down if the current exceeds 3A (1725,
1725EX, 1728, and 1728EX) or 2.5A (1758, and 1758EX). When this occurs the “Maximum Bell Current” failure will
appear in the keypads’ Trouble Display (see page 54). If the load on the BELL terminals returns to normal, the
control panel will re-instate power to the BELL terminals. When connecting sirens (speakers with built-in siren
drivers) please verify correct polarity. Connect the positive lead to the BELL+ terminal and the negative lead to the
BELL- terminal of the control panel as shown in Figure 2-1A.
If the BELL output is not being used, the "Bell Disconnected" failure will remain in the keypads’
Trouble Display (see page 54). To avoid this, connect a 1KΩresistor across the BELL terminals.
Table 2: Current Consumption Table
Modules Current Consumption
Spectra 1686H and 1686V 10-Zone LED Keypad 62mA typ. 116mA max.
Spectra 1689 16-Zone LED Keypad 50mA typ. 117mA max.
Spectra 1641 LCD Keypad 60mA typ. 80mA max.
SPC-319 LiberatorTM Wireless Bus Expansion Module 70mA typ. 70mA max.
ZX8 8-Zone Hardwire Expansion Module 30mA typ. 30mA max.
SPC-ZX4 4-Zone Hardwire Expansion Module 12mA typ. 12mA max.
Motion Detectors (see detector instructions for details) 10-50mA typ.

10 REFERENCE & INSTALLATION MANUAL
2.8 PROGRAMMABLE OUTPUT CONNECTIONS
The Spectra Series control panels include one or more programmable outputs (PGMs).
When a specific event occurs in the system, a PGM can reset smoke detectors, activate
strobe lights, open/close garage doors and much more. PGM1 provides a maximum
150mA output and PGM2 provides up to 2.5A and can be used as a strobe output (see
page 40). PGM2 is limited by the power source being used. If powered by the BELL+
terminal, the combined current consumption of the bell output and PGM2 must not
exceed 2.5A. If it is powered by the aux.+, the devices connected to the auxiliary power
supply and PGM2 must not exceed 1.1A. If it is powered by an external device, PGM2
can supply 2.5A. If the current draw on the PGM is to exceed the current output, we
recommend the use of a relay as shown in Figure 2-2. For details on how to program the
PGM, refer to PGM Programming on page 39.
2.9 ALARM RELAY
The Spectra 1758 and 1758EX control panels have an optional 5A relay. This relay can be connected as shown in
Figure 2-1B on page 8. Please note that the Alarm Relay can be programmed to follow the bell output or the
activation and de-activation of the Global PGM (see Alarm Relay Options on page 40).
2.10 KEYSWITCH CONNECTIONS
Keyswitches allow users to arm or disarm a partition by pushing button or by activating a
switch with a key. You must enable zone 2 as a Keyswitch Zone (see page 22), connect
the keyswitch to zone input terminal 2 as shown in Figure 2-3 and program the Keyswitch
Options as described on page 24.
2.11 KEYPAD INSTALLATION
To connect the keypads to the control panel, remove the back cover and wire the GRN, YEL, RED, and BLK terminals of
each keypad to the corresponding terminals on the control panel as shown in Figure 2-1A on page 7. There is no limit to
the number of keypads thatcan be connected to the control panel so long as the current consumption does not surpass
the maximum current consumption of the control panel's Auxiliary Power Terminals (see page 9). For information on
Keypad Tamper Supervisionreferto page 42 and for information on Keypad Zone Connections refer to page10.
2.12 KEYPAD ZONE CONNECTIONS
Each keypad has one zone input terminal, allowing you to connect one motion detector or door contact directly to a
keypad. The keypad can then communicate the status of the zone to the control panel. A maximum of two keypad
zones can be used with each control panel. After connecting the device as shown in Figure 2-1A on page 7, the
zone's parameters must be defined. For details on zone recognition and Zone Programming refer to page 20.
Example: A door contact located at the entry point of an establishment can be wired directly to the input terminal of
the entry point keypad instead of wiring the door contact all the way to the control panel.
If there are more than 2 keypads connected to the control panel and at least one keypad zone is being used,
connect as shown in Figure 2-4 and program as follows:
• Donot exceed the control panel’smaximum current consumption.
• Donot place a jumper across the zone and “blk” terminals of all keypadsthat arenot using their keypad zone.
• Make sure that “Keypad Zone Sending” is enabled on all 1641 LCD Keypads. Todo so:
Step 1: Press and hold the [0] key for two seconds to enter the keypad’s programming mode.
Step 2: Enter the [KEYPAD CODE]. Default: 000000
Step 3: Press the [2] key (“Options”) or use the arrow keys to scroll to option [2] (“Options”) and then press the
[ENTER]key.
Step 4: Make sure option [1] (“Keypad Zone Sending”) is enabled. If it is not enabled, press the [1] key to enable
the option and then press [ENTER].
Figure 2-2: PGM
Fi
gure
2
-
3
:
K
eysw
it
c
h

SPECTRA SERIES 11
Figure 2-4: Example of Keypad Zone Connections
2.13 SINGLE ZONE INPUTS
Detection devices such as motion detectors and door contacts are connected to the control panel's zone input
terminals labeled between 1 and 5 depending on the Spectra control panel being used. Figure 2-5 demonstrates
single zone input terminal connections recognized by the Spectra Series control panels. Once connected, the
associated zone's parameters must be defined. For more details, please refer to Zone Programming on page 20.
Figure 2-5: Single Zone Input Connections

12 REFERENCE & INSTALLATION MANUAL
2.14 DOUBLE ZONE INPUTS (WITH ATZ OPTION ONLY)
Enabling the ATZ feature (see page 25) allows you to install two detection devices per input terminal. The ATZ
featureis a software-oriented feature. Therefore, there is no need for extra modules, simply connect the devices as
shown in Figure 2-6. Devices connected to input terminals must be assigned to a zone and the zone's parameters
must be defined. Please refer to Zone Programming on page 20 of this manual for more information. The status of
each zone will be displayed on the keypads and the control panel can send separate alarm codes for each zone.
2.15 FIRE CIRCUITS
When zone 3 is defined as a 24Hr. zone (see page 22), the control panel will recognize zone 3 as a Fire Zone,
enabling smoke detectors to be connected as shown in Figure 2-7. Fire zones must use a 1kΩEOL resistor. If there
is a line short or if the smoke detector becomes active, whether the system is armed or disarmed, the control panel
will generate an alarm.
2.15.1 FIRE CIRCUIT: 4-WIRE INSTALLATION:
In the event power is interrupted, the relay will cause the control panel to transmit the Fire Loop Trouble
report if programmed in section [206]. To reset (unlatch) the smoke detectors after an alarm, install the
smoke detectors as shown in Figure 2-7. Then program the PGM with the "[PG]/[FNC1] key was pressed"
activation event (see page 39). Pressing the [PG] or [FNC1] key will interrupt power to the smoke detectors
for 4 seconds (see PGM Delay on page 40).
Fi
gure
2
-
6
:
D
ou
bl
e
Z
one
(ATZ)
I
npu
t
C
onnec
ti
ons
Figure 2-7: Fire Zone Connections

SPECTRA SERIES 13
2.16 CONNECTING A LIBERATOR SPC-319 WIRELESS MODULE
The Liberator Wireless Bus Module (SPC-319) allows you to add up to eight fully programmable remote controls
and up to eight Liberator Wireless Detectors and/or Contact Switches (door contacts). For information on how to
program this module, please refer to page 47. (Not compatible with the Spectra 1758 and 1758EX.)
2.16.1 LOCATION
Mount the Liberator on a wall allowing at least 5 cm (2") around the module to permit adequate ventilation
and heat dissipation. Select a site that is not susceptible to drastic temperature changes. Avoid installation
near or in the path of strong RF fields (i.e. neon lights, computers), on or near metal objects, circuit breaker
boxes, air conditioners, and heater ducts since they may cause interference and reduce its sensitivity. We
recommend installing it in a centralized location on the main floor. Avoid installing it in the basement.
2.16.2 CONNECTIONS AND MOUNTING
Firmly screw the two antennas into the connectors marked "ANT" on the Liberator Wireless Bus Module as
shown in Figure 2-8. Using a drill or screwdriver, punch out the four mounting holes on the back of the
plastic case. Align the six holes of the printed circuit board with the six pins on the back plastic mounting
case and snap into place. If placed correctly, the antennas will lean directly over the grooves in the
mounting case. Connect the “GRN” and “YEL” terminals from Wireless Module to the corresponding “GRN”
and “YEL” terminals of the control panel. Connect the “RED” terminal to the “AUX+” of the control panel.
Connect the “BLK” terminal to the “AUX-” of the control panel.
The Liberator Module does not function with the Spectra 1758 and 1758EX. Do not cut, bend, or alter
the antennas. Avoid mounting the Receiver Module near or on metal as this may affect its sensitivity.
Remove AC power and then remove the battery before adding a bus module to the system or it may
cause communication trouble. Do not connect more than one Liberator Wireless Module to the panel.
2.17 CONNECTING A ZONE EXPANSION MODULE (SPC-ZX4/ZX8)
The Zone Expansion Modules connect to the Spectra control panel's communication bus providing you with up to 4
(SPC-ZX4) or up to eight (ZX8) additional hardwired inputs and one 50mA on-board PGM output (ZX8 only). For details
on how to program these modules, refer to page 50. Connect the four terminals labeled RED, BLK, GRN and YEL of each
Zone ExpansionModule to thecorresponding terminals on the controlpanel as shown in Figure 2-9 on page 14.
Do not connect more thanone Zone Expansion Module to the control panel. The ZX4 module is identical
to the ZX8 except there are no LEDs, there are only four zone inputs (Z1 to Z4) instead of eight and no
PGM output.
Fi
gure
2
-
8
:
Lib
era
t
or
Wi
re
l
ess
B
us
M
o
d
u
l
e
(SPC
-
319)

14 REFERENCE & INSTALLATION MANUAL
2.17.1 ZONE CONNECTIONS (SPC-ZX4/ZX8)
Each input terminal, allows you to connect one detection device. These devices are connected exactly as
shown in Figure 2-5 on page 11. Devices connected to the Zone Expansion Module's input terminals must
be enabled as described in Zone Input Assignment on page 50 and the its parameters must be defined as
explained in Zone Programming on page 20. The Zone Expansion Modules will communicate the status of
the zones to the control panel through the communication bus.
The Zone Expansion Modules do not support the zone doubling (ATZ) feature.
2.17.2 ZONE EXPANSION MODULE TAMPER CONNECTIONS
The Zone Expansion Modules do not come equipped with a tamper switch. Although, if required you can
enable Tamper Recognition (Zone Module) (see page 50), which will reserve input terminal Z1 as a tamper
switch input. This allows you to connect a tamper switch to input Z1 as shown in Figure 2-9. When a
tamper is detected on the module, it will send a tamper report (originating from the zone assigned to input
Z1) to the control panel via the communication bus.
With Zone Expansion Module Tamper Recognition enabled, do not connect anything other
than the tamper switch to input terminal Z1.
Figure 2-9: Zone Expansion Module (ZX8)

SPECTRA SERIES 15
PART 3: PROGRAMMING METHODS
3.1 WINLOAD SOFTWARE FOR WINDOWS
Program the Spectra Series control panels remotely or on-site using the Winload Software for Windows®. For more
information, contact your local Paradox Distributor or visit our web site at http://www.paradox.ca. If you are using the
WinLoad software, you must program the features explained on pages 45 to 46.
3.2 PROGRAMMING USING A KEYPAD
Use the supplied "Spectra Programming Guide" to keep track of which sections were programmed and how. We
recommend you read this entire manual before you begin programming.
3.2.1 SINGLE DIGIT DATA ENTRY METHOD (HEXADECIMAL AND DECIMAL)
Single Digit Data Entry is used in all sections except those specified in Multiple Feature Select Programming
Method. After entering the programming mode as described in the shaded box above, some sections will
require that you enter Decimal values from 000 to 255 . Other sections will require that you enter Hexadecimal
values from 0 to F . The required data will be clearly indicated in this manual as well as in the Spectra Series
Programming Guide. When entering the final digit in a section, the control panel will automatically save and
advance to the next section. With the exception of sections 001 to 016, where after entering the first two digits,
the control panel will switch to Multiple Feature Select Programming.
3.2.2 MULTIPLE FEATURE SELECT PROGRAMMING METHOD
Sections: [001] to [016], [127] to [138], [302] to [348], [610], [650] to [651]
After entering the programming mode as described in the shaded box above, each option from [1] to [8] will
represent a specific feature or option. Press the key corresponding to the desired option and the
corresponding light will illuminate or the option number will appear in the LCD display. This means the option is
on. Pressthe key again to extinguish the corresponding light orremove thedigitfrom the LCD display, thereby,
turning off the option. Please note that pressing the [
FORCE
] key will set all 8 options to “off”. Press the keys as
many times as you need until all 8 options in the current section are set. When the options are set, press the
[
ENTER
] key to save and advance to the next section.
How Do I Enter Programming Mode?
STEP 1: Press [ENTER]
STEP 2: Enter your [INSTALLER CODE](default: 000000)
STEP 3: Enter 3-digit [SECTION]you wish to program
STEP 4: Enter required [DATA]
Table 3: Decimal and Hexadecimal Programming Table
Value or Action What Do I
Press? What Do I See?
10-Zone LED 16-Zone LED LCD
Values1 to 9 [1] to [9] [1] to [9] [1] to [9] [1] to [9]
A (hexa only) [0] [0 (10)][10] A
B (hexa only) [STAY][
STAY][11] B
C (hexa only) [BYP][
BYP][12] C
D (hexa only) [MEM][
MEM][13] D
E (hexa only) [TBL] / [TRBL][
TBL][14] E
F(hexa only) [PG] / [FNC1] [PG][15] F
Insert Blank Digit [FORCE] Displays next digit or next section
Exit Without Saving [CLEAR][
ENTER] flashes [ARM1] & [STAY1] flash “SECTION [ ]”
Save Data (hexa only) [ENTER] Advances to the next section

16 REFERENCE & INSTALLATION MANUAL
3.2.3 DATA DISPLAY MODE (LED KEYPADS ONLY)
In the Data Display Mode you can view the programmed contents of each section one digit at a time. After
entering the desired 3-digit section (see step 3 of the “How Do I Enter The Programming Mode” box on the
previous page), press the [ENTER]key to access the Data Display Mode. This mode will not function with
sections using the Multiple Feature Select Programming Method.
Figure 3-1: Data Display Mode (LED Keypads Only)
3.3 PROGRAMMING USING A PARADOX MEMORY KEY
Copy the programmed contents of one control panel into the Paradox Memory Key. Then copy the contents of the
Memory Key into as many control panels as you need. Each control panel is programmed in less than 3 seconds.
If used with a Spectra 1758/EX, you will have to reassign the remote controls (see page 53).
Download to DESTINATION Control Panel
1) Remove AC and battery power from the control panel.
2) Insert the Memory Keyonto the serial connector labeled “KEY” on the Spectra control
panel to which you wish to download the contents of the memory key to.
3) Reapply AC and battery power.
4) In installer programming mode, enter section [900], then press [ENTER] to acknowledge.
5) When the keypad emits a confirmation beep, remove the Memory Key.
Copy to Memory Key from SOURCE Control Panel
1) Remove AC and battery power from the control panel.
2) Insert Memory Keyonto the serial connector labeled “KEY” on the Spectra control panel
from which you wish to copy. Make sure the write protect jumper of the Memory Key is on.
3) Reapply AC and battery power.
4) In installer programming mode, enter section [902], then press [ENTER] to acknowledge.
5) When the keypad emits a confirmation beep, remove the Memory Key. Remove the
Memory Key’s jumper if you do not wish to accidentally overwrite the contents of the key.
Figure 3-2: Paradox Memory Key.

SPECTRA SERIES 17
PART 4: ACCESS CODES
The Spectra Series control panels support the following 48 access codes:
4.1 ACCESS CODE LENGTH
Section [127] = System Options
Option [2] OFF = 6-Digit Access Codes
Option [2] ON = 4-Digit Access Codes (default)
All access codes can be set to lengths of either 4 or 6-digits. When the 4-digit option is selected, entering a 4-digit
code will allow access. Using the 6-digit option, entering 6 digits is required to allow access.
If the Access Code Length is changed from four digits to six digits when access codes have
already been programmed, the control panel will automatically add the last 2 digits by using the
first 2 digits. For example, if the access code is 1234 and you switch to 6 digits, the code will
become 123412. Be sure to verify the access codes after switching from 4-digit access codes to 6-
digit codes. When switching from six digits to four digits, the control panel will simply remove the
final two digits of the access code. For example, 123456 will become 1234.
4.2 INSTALLER CODE (Default: 000000)
The Installer Code is used to enter the control panel's programming mode (see page 15), which allows you to
program all the features, options and commands of the control panel. The Installer Code can be 4 or 6-digits in
length (see above) where each digit can be any value from 0-9. The Installer Code cannot be used to program the
Master or User Access Codes. To program the Installer Code press:
[ENTER] + [CURRENT INSTALLER CODE] + [281] + new 4 or 6-digit Installer Code
4.3 SYSTEM MASTER CODE (Default: 123456)
With the System Master Code a user can use any arming method and can program any User Access Code but not the
User Code Options described on page 17. The System Master Code can be 4 or 6 digits in length (see above), where
each digit can be any digit from 0 to 9. To change theSystem Master Code press:
[ENTER] + [INSTALLER CODE] + [301] + new 4 or 6-digit System Master Code
4.4 USER CODE OPTIONS
Sections [302] to [348] - Feature Select Method: Options [1] to [7] on/off
The User Code Options define which arming methods each user can use to arm or disarm the system. Regardless
of these settings, all users can Regular Arm assigned partitions and all users except those with the Arm Only option
can disarm an assigned partition, regardless of how it is armed. Select one or more of the options described on the
following pages for each User Access Code, where sections [302] to [348] represent User Access Codes 002 to
048. For information on how User Access Codes are programmed, please refer to page 55.
INSTALLER CODE: Used to program all control panel settings except User Access Codes.
SYSTEM MASTER CODE (001) Provides full access. Arm and disarm using any method described in the User Code
Options on page 17 as well as program the User Access Codes.
MASTER CODE 1 (002): Permanently assigned to partition 1. Same as a regular User Code except it can
also program access codes for User Codes assigned to partition 1.
MASTER CODE 2 (003): Permanently assigned to partition 2. Same as a regular User Code except it can
program access codes for User Codes assigned to partition 2. If the system is not
partitioned Master Code 002 will be assigned to partition 1.
45 USER CODES (004-048): Can arm and disarm as per User Code Options in section 4.4.

18 REFERENCE & INSTALLATION MANUAL
4.4.1 PARTITION 1 ASSIGNMENT
Sections [302] to [348] = User Codes 002 - 048
Option [1] OFF = Deny access to partition 1
Option [1] ON = User code has access to partition 1 (default)
If Partitioned (see page 41), user codes with this option enabled can arm and disarm partition 1.
If the system is not partitioned, you must assign partition 1 to the User Access Code.
Otherwise, the User Access Code will be considered disabled.
4.4.2 PARTITION 2 ASSIGNMENT
Sections [302] to [348] = User Codes 002 - 048
Option [2] OFF = Deny access to partition 2 (default)
Option [2] ON = User code has access to partition 2
If the system is partitioned (see page 41), user codes with this option enabled can arm and disarm partition
2. If the system is not partitioned, the control panel ignores this option.
4.4.3 BYPASS PROGRAMMING
Sections [302] to [348] = User Codes 002 - 048
Option [3] OFF = Bypass Programming Disabled
Option [3] ON = Bypass Programming Enabled (default)
User codes with this option enabled can perform Bypass Programming in assigned partitions.
4.4.4 STAY ARMING
Sections [302] to [348] = User Codes 002 - 048
Option [4] OFF = Stay Arming Disabled
Option [4] ON = Stay Arming Enabled for selected User Code (default)
User codes with this option enabled can Stay Arm assigned partitions.
4.4.5 FORCE ARMING
Sections [302] to [348] = User Codes 002 - 048
Option [5] OFF = Force Arming Disabled (default)
Option [5] ON = Force Arming Enabled for selected User Code
User codes with this option enabled can Force Arm assigned partitions.
4.4.6 ARM ONLY
Sections [302] to [348] = User Codes 002 - 048
Option [6] OFF = Arm Only Disabled (default)
Option [6] ON = Arm Only Enabled for selected User Code
Theuser code withthis option enabled can armassigned partitions but can not disarm anypartitions. The type
of arming is dependent on the other User Code Options selected. Please note that with the Arm Only option,
the user can cancel a recently armed system by re-entering the access code before the end of the Exit Delay.
4.4.7 PGM ACTIVATION
Sections [302] to [348] = User Codes 002 - 048
Option [7] OFF = Arm, Disarm & PGM activation for selected User Code (default)
Option [7] ON = PGM only for selected User Code
With option [7] off, entering the access code will arm or disarm the system as well as activate or deactivate
a PGM. The appropriate PGM Activation/Deactivation Event must also be programmed (see page 39).
With option [7] on, the control panel will ignore all other User Code Options. Therefore, entering the access
code will only activate or deactivate the PGM.