Spectravision PL-REM-200 User manual

LED pool light Remote Control
with built in transformer
OWNER’S MANUAL
PL-REM-200
Controls Spectravision Pool Lights
and 2 auxiliary circuits
lighting
Long range DuraLink™ version

Table of contents
Technical specifications
Box contents
Installation instructions
Pairing Handheld Transmitter & controller
Handheld transmitter functions
Replacing transmitter battery
Troubleshooting
Page 3
Page 4
Page 5
Page 6
Page 7
Page 7
Page 7
lighting
page 2 of 8

Technical specifications
page 3 of 8
Electrical specifications
General specifications Controller
Ambient air temperature
Humidity
Dimensions
Weight
Ingress protection rate
0°C ... +40°C
10% ... 90% RH
non condensing
195x194x90 mm
3,2 kg
IP54
Nominal Input voltage
Output voltage on Lamp Output
Max output current on Lamp Output
Max rating Relay Contact A and B
Resistive Load
Inductive Load
Transformer VA rating
Fuse type
Frequency band transmitter
IEC Protection Class
230 VAC 50 Hz
12 VAC
16,7 A
14A 250VAC
14A 30VDC
6A 250VAC
6A 30VDC
200VA
5x20mm cartridge fuse
5A 250V slow blow/time lag
868 MHz
Class II

page 4 of 8
Box contents
lighting
12
45
1. PL-REM-200 controller
2. Handheld transmitter (DuraLink™ version)
3. Spare battery (type A23 12V)
4. Screws (4x) & wall plugs (4x)
5. Owners’s manual
3

Installation instructions
page 5 of 8
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal
• Connect the swimming pool lights to the “Lamp 12VAC output”
terminal
Optional: The “Switch A” & “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.
Make sure the total load of pool lights does not exceed 200Watt
Red status LED
Spare fuse

page 6 of 8
Pairing handheld transmitter & controller
lighting
The handheld transmitter is already paired in the factory and ready to
use. The PL-REM-200 can pair with up to 6 handheld transmitters. In
case a problem arises, the pairing process can be done manually:
Manual Pairing process:
Make sure the PL-REM-200 is connected to a power source.
1. Press the pairing button on the small circuit board, inside the con-
troller for at least 5 seconds.
--> The LED will start to blink fast
2. Within 25 seconds, press any button on the handheld transmitter.
--> If the transmitter is paired correctly, the LED will flash slowly for 5 times
--> If the PL-REM-200 pairing memory is full, the LED will flash 15 times.
This means 6 handheld devices have already been paired.
To unpair all handheld transmitters with the controller: Push the pair-
ing button for at least 5 seconds, then do nothing for at least 25 sec-
onds.
--> The pair memory will be erased - the red LED will flash 5x on/o.
Red LED
Pairing button

Handheld transmitter functions
page 7 of 8
PROBLEM SOLUTION
The controller doesn’t react
to transmitter commands
• Check the battery of the hand-
held transmitter
• The transmitter is not paired-
correctly with the controller.
Repeat the pairing process
• Reduce the distance between
handheld transmitter and PL-
REM-200 and/or remove ob-
stacles
The pool lights don’t work • Check the red status LED
• Check if there is 12VAC output
at the terminals of the controller
• Check the fuse of the controller
Troubleshooting
Toggle Output A ON/OFF
Toggle Output B ON/OFF
Toggle the lamps ON/OFF
Go to next color scenario
Replacing transmitter battery
• Remove the philips head screw and open the transmitter
• Replace the battery, respecting the polarity
Battery type: A23 12V
-
+
If the fuse is ok, and there is still no
12VAC output, contact your distributor

lighting
Contact details
Propulsion Systems bvba
Dooren 72
1785 Merchtem, Belgium
Tel [phone]
Fax [phone]
www.propulsionsystems.be
[email protected]
We reserve the rights to change all or part of the contents of this document without prior notice
402-0019-170118