Spectravision PL-REM-P User manual

LED pool light Remote Control
OWNER’S MANUAL
PL-REM-P
Controls Spectravision Pool Lights
and 2 auxiliary circuits
Long range DuraLink™ version

Table of contents
Technical specifications
Box contents
Installation instructions
Pairing Handheld Transmitter & controller
Handheld transmitter functions
Replacing transmitter battery
Troubleshooting
Page 3
Page 4
Page 5-6
Page 7
Page 8
Page 8
Page 9
page 2 of 12

Technical specifications
page 3 of 12
Electrical specifications
General specifications Controller
Ambient air temperature
Humidity
Dimensions
Weight
Ingress protection rate
0°C ... +40°C
10% ... 90% RH
non condensing
150x157x51 mm
500 g
IP54
Nominal Input voltage
Max rating Relay Contacts
“Color&Light”, “A” and “B”
Resistive Load
Inductive Load
Frequency band transmitter
IEC Protection Class
230 VAC 50 Hz
14A 250VAC
14A 30VDC
6A 250VAC
6A 30VDC
868 MHz
Class II
For operation only with 12VAC safety isolation transformer
to power Spectravision®LED Pool Lights

page 4 of 12
Box contents
12
45
1. PL-REM-P controller
2. Handheld transmitter (DuraLink™ version)
3. Spare battery (type A23 12V)
4. Screws (4x) & wall plugs (4x)
5. Owners’s manual
3

Installation instructions
page 5 of 12
230VAC
Garden lights
Pool cover
230VAC 230VAC
12VAC
Option 1: PL-REM-P in transformer primary
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal
• Connect the primary circuit of a 12VAC transformer (sold sepa-
rately) in series with the “Color&Light” terminal of the PL-REM-P.
The “Color&Light” relay contact has an output of 14A, which can
drive a 12V transformer of max. 3000W (220Vx14A).
Optional: The “Switch A” & “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.

page 6 of 12
Option 2: PL-REM-P in transformer secondary
• Connect a 230VAC power source to the “220-240VAC INPUT”
terminal
• Connect the secondary circuit of a 12VAC transformer (sold sep-
arately) in series with the “Color&Light” terminal of the PL-REM-P.
The “Color&Light” relay contact has an output of 14A, or 170W on a 12V
transformer secondary (14Ax12V). The total load of pool lights can not
exceed this.
Optional: The “Switch A” & “switch B” terminals can be used to control
auxiliary circuits like a pool cover or garden lights.
230VAC
Garden lights
Pool cover
230VAC 230VAC
12VAC

page 7 of 12
Pairing handheld transmitter & controller
The handheld transmitter is already paired in the factory and ready
to use. The PL-REM-P can pair with up to 6 handheld transmitters. In
case a problem arises, the pairing process can be done manually:
Manual Pairing process:
Make sure the PL-REM-P is connected to a power source.
1. Press the pairing button on the small circuit board, inside the con-
troller for at least 5 seconds.
--> The LED will start to blink fast
2. Within 25 seconds, press any button on the handheld transmitter.
--> If the transmitter is paired correctly, the LED will flash slowly for 5 times
--> If the PL-REM-P pairing memory is full, the LED will flash 15 times.
This means 6 handheld devices have already been paired.
To unpair all handheld transmitters with the controller: Push the pair-
ing button for at least 5 seconds, then do nothing for at least 25 sec-
onds.
--> The pair memory will be erased - the red LED will flash 5x on/o.
Red LED
Pairing button

Handheld transmitter functions
page 8 of 12
Toggle the lamps ON/OFF
Go to next color scenario
Pulse Output A
Pulse Output B
Replacing transmitter battery
+
-
• Remove the philips head screw and open the transmitter
• Replace the battery, respecting the polarity
Battery type: A23 12V

PROBLEM SOLUTION
The controller doesn’t react
to transmitter commands
• Check the battery of the hand-
held transmitter
• The transmitter is not paired-
correctly with the controller.
Repeat the pairing process
• Reduce the distance between
handheld transmitter and PL-
REM and/or remove obstacles
The pool lights don’t work • Check if all connections are
made according to the electri-
cal scheme on page 5 or 6.
• Check if the “Color&Light” out-
put terminals of the controller
switch on and of when pushing
the on/o button on the trans-
mitter.
Troubleshooting
page 9 of 12

Declaration of Conformity
!
We, Propulsion Systems bvba, declare under our sole responsibility, that the equipment
described below conforms with the essential requirements of the following directives and
standards:
!
DIRECTIVE 2011/65/EC (RoHs 2)
•EN50581
!
DIRECTIVE 1999/5/EC Radio equipment and telecommunications terminal equipment
and the mutual recognition of their conformity
•EN 300 220 Electromagnetic compatibility and Radio spectrum Matters (ERM); Short
Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz
frequency range with power levels ranging up to 500 mW
!
DIRECTIVE 2004/108/EC Electromagnetic compatibility
•EN 300 683 (Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for Short Range Devices (SRD) operating
on frequencies between 9 kHz and 25 GHz)
•EN 301 489-3 (Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part
3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between
9 kHz and 40 GHz)
!
!
!
Equipment: handheld transmitter/receiver for remote control & base unit transmitter /
receiver 868MHz band DuraLink™
!
Trade Mark: SpectraVision™
!
Model Nr.: Description:
PLA-REM (COMMUNICATIONS & REMOTE CONTROL BOX FOR ADAGIO+ RGB
DuraLink™)
PLA-REM-300 (350VA PSU & COMMS BOX FOR ADAGIO+ RGB DuraLink™)
PL-REM (REMOTE CONTROL FOR MOONLIGHT & ADAGIO+ DuraLink™)
PL-REM-P (REMOTE CONTROL FOR MOONLIGHT & ADAGIO+ (PULSED) DuraLink™)
PL-REM-200 (200VA PSU & REMOTE CONTROL FOR MOONLIGHT & ADAGIO+
DuraLink™)
TX868-PLA (TRANSMITTER ; DuraLink™ 868MHz ; for PLA-REM(-300))
TX868-PL (TRANSMITTER ; DuraLink™ 868MHz ; for PL-REM(-60/200))
!
Propulsion Systems bvba
Dooren 72
B-1784 Belgium
!
!
Date of signature:
Signature:
Name: Dhr. Marc Lamberts
Title:
21/10/2014
GM
page 10 of 12

page 11 of 12

Contact details
Propulsion Systems bvba
Dooren 72
1785 Merchtem, Belgium
Tel [phone]
Fax [phone]
www.propulsionsystems.be
[email protected]
We reserve the rights to change all or part of the contents of this document without prior notice
402-0032-150630