Spectrum Industries 37130 User manual

0118583R7 Page 1 of 4
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Display Stand
37130
(1) 0193628
VESA mount
(4) 0108896
1/4-20 Flanged
serrated locknut
(16) 052605
1/4-20 x 15mm
JC bolt
(1) 0118193
End cap 3” x 3”
(1) 0118510
Upright assembly
(2) 0173165
Upright bracket
Figure 1
Rubber thread
protectors
Bottom of upright
assembly
(1) 025039
4mm Hex wrench
1. With the upright assembly upside-down, remove the rubber
thread protector from each threaded stud. Figure 1.
󰀨

”
4mm
Remove thread protectors
1

0118583R7 Page 2 of 4
Figure 2.1
Figure 2.3
Upright
assembly
Worksurface
1/4-20 Flanged
serrated locknut
(4 required)
Mounting holes and cutout needed

1. Be sure the worksurface being used has the cutout / hole pattern
shown in Figure 2.1, or Figure 2.2.
Figure 2.2
Optio Tables
InVision / Element / Nano Tables
2. An unattached worksurface will facilitate installation of the display
stand fasteners. If attached, remove the worksurface fasteners
securing it to the base and slide the worksurface 6” over the base to
provide access to the display stand mounting holes. Figure 2.3.
3. Align the studs and insert the upright into the worksurface mounting holes.
4. With a second person holding the upright, Install (4) 1/4-20 Flanged
serrated locknuts and tighten securely.
Note: For InVision Nano table installation,
see p.4 for special instructions.
Pull worksurface
out about 6” to ac-
cess display stand
mounting holes
Worksurface cutouts
2

0118583R7 Page 3 of 4
Figure 4
Upright
assembly
1/4-20 x 15mm JC
bolts (4 required)
End cap
Figure 5
Upright opening
for routing cables
VESA mount
1. Attach the (2) upright brackets to the upright assembly as shown
using 1/4-20 x 15mm JC bolts (2 per). Tighten securely.
Note: Multiple mounting holes / height positions are available on
the upright assembly). Figure 3.
1. Refer to the instructions included with the VESA mount for complete
display installation procedure. (The hanging rails get installed to the
back of the display.)
2. Route cables through the upright opening.
3. Install end cap on top of upright.
WARNING
The display should always be removed
from the stand before moving the unit.
Hanging rail
Install display
5
Install upright brackets
3
Figure 3
1. Attach the VESA mount to the (2) upright brackets
using (12) 1/4-20 x 15mm JC bolts. Figure 4.
2. Tighten all bolts securely
Install VESA mount
4
1/4-20 x 15mm
JC bolts
(12 required)
Upright bracket
Upright bracket
VESA mount
Hanging rail
Worksurface
Refer to the instructions in-
cluded with the display mount
for complete VESA / display
installation procedure.
Refer to the instructions in-
cluded with the display mount
for complete VESA / display
installation procedure.
• The assembled display stand accommodates most
43”-90” displays.
• Be sure display does not exceed the weight capacity
of 125 lb.
• If installing the display stand onto a Spectrum
Console Gaming Hub, be sure the top of the installed
monitor will not exceed a 66” height from the oor.
• If installing the display stand onto a Spectrum
Console Gaming Hub, be sure the top of the installed
monitor will not exceed a 66” height from the oor.

InVision Nano Table Installation addendum
0118583R7 Page 4 of 4 © 2023 Spectrum Industries Inc., All rights reserved.
1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM
1. Remove the (4) screws shown. Figure 6.1.
2. Remove end panel.
Figure 6.1
End panel
Remove these screws
Remove these
screws
Note: To install the Display Stand on a Nano table,
the end panel must be removed prior to installing.
1/4-20 Flanged
serrated locknut
(4 required)
3. Align the studs and insert the upright into the worksurface
mounting holes.
4. With a second person holding the upright, install the (2) inner
1/4-20 Flanged serrated locknuts. Figure 6.2.
5. Replace the end panel.
6. 
7. Tighten all locknuts securely.
Figure 6.2
Upright assembly