Spectrum Technologies Field Scout 2265FS User manual

Catalog #’s
2265FS, 2265FSTP
Field Scout
®
Soil & Water
EC Meter
Technologies, Inc.
Spectrum

2
CONTENTS
CONTENTSCONTENTS
CONTENTS
Introduction 3
EC Probe 4
Probe Calibration 6
Meter Configuration 8
Direct Soil EC Readings 10
SME Measurement 11
Liquid Measurement/Other Features 12
Maintenance/Battery Replacement 13
Probe/Tip Replacement 14
Checking Probe Connection 16
Specifications 17
Appendices
1. Preferred EC Values for Selected Plants 18
2. Interpreting EC Readings From Turf Grass 20
3. Classification of Irrigation Water 22
4. Classification of Greenhouse Media 23
5. Diagnostic Messages 24
6. Celsius to Fahrenheit Conversion Chart 25
Warranty 26
This manual will familiarize you with the features and
operation of your Field Scout Soil & Water EC Meter.
Please read this manual thoroughly before using
your meter. For customer support or to place an
order call Spectrum Technologies, Inc.
800-248-8873 or [phone]
between 7:30 am and 5:30 PM CST
FAX at 815-436-4460
e-mail [e-mail].
Website: www.specmeters.com
Spectrum Technologies, Inc.
12360 S. Industrial Dr. East
Plainfield, IL 60585

3
Congratulations on the purchase of your Field Scout
Soil & Water EC Meter. This instrument has been
specifically designed for direct measurement of salts in
soil media as well as water or nutrient solutions. This
manual describes how to use your meter and keep it
working accurately for many years. Please read it
thoroughly to get effective performance from your me-
ter.
The salinity of the soil solution, irrigation water or fertil-
izer solution is an important parameter affecting the
root zone environment. Any of these factors can have
a significant effect on plant growth and physiology.
The easiest way to monitor salinity is by measuring the
electrical conductivity (EC). EC is strongly correlated
to the salinity of the soil solution. EC measurement is
also affected by temperature and, to a lesser degree,
by soil moisture content.
Use this portable EC meter and probe to measure sa-
linity in greenhouse soil media right on the spot with-
out tedious soil sampling and preparation. Green-
house production managers can compare readings
from plant to plant and fine-tune their fertility program
because measurements can be made directly in a plug
tray cell without cannibalizing the seedlings. Turf
managers can monitor for high salt levels on golf
course greens and determine when to flush (leach)
salts before turf quality declines.
The meter comes with the Field Scout Soil/Water EC
probe. This single, stainless steel probe has a spe-
cially designed conical tip. It can measure liquid EC
(water or nutrient solutions) or in-situ soil salinity. The
probe automatically compensates for temperature.
ntroduction

4
Electrical conductivity (EC) is an important parame-
ter in evaluating irrigation water and fertilizer solu-
tions. Crops can be damaged if irrigated with water
with a high conductivity. The quality of irrigation wa-
ter has been classified into 5 separate categories
(See Appendix 3, p. 22). EC is also an indicator of
the strength of fertilizer solutions. In greenhouse ap-
plications and other situations requiring frequent fer-
tilization, EC should be checked regularly to ensure
the plants are getting sufficient nutrients while avoid-
ing the effects of salt toxicity. See Appendix 1 (p.
18) for a list of preferred EC values for some com-
mon plants. Typically, younger plants will require
lower EC than mature plants.
The stainless
steel soil EC
probe is de-
signed to be in-
serted directly
into soil. The
sensing surface
is composed of 2
pairs of elec-
trodes on the
probe tip. Addi-
tionally, the
probe is narrow
in diameter so it
can be used ef-
fectively in plug
trays.
EC Probe
Sensor
Electrode
Pair

5
Because the EC readings are affected by moisture
content, it is important that soil moisture content
does not differ significantly between readings. An
easy way to achieve this condition is by taking meas-
urements approximately 30 to 60 minutes after an
irrigation. This should ensure the soil moisture level
has approximately reached field capacity.
The probe should be inserted in the root zone. The
measurement region is at the tip of the probe. For
turf, the root zone is approximately 2” - 4”. For vege-
tables and small plants, this is about 8” - 12”. Wait
until the meter reading stabilizes before withdrawing
the probe. Taking several measurements will allow a
representative average to be computed.
Important: Do not touch the sensor tip with your
fingers. The oils on the skin will affect the
probe’s measurement accuracy.

6
The meter and probe are factory calibrated. How-
ever, to ensure accuracy, the meter should be cali-
brated at least once a month. The meter is cali-
brated to an EC of 2764 µS/cm (2.76 mS/cm) cali-
bration solution. Periodically, the calibration of the
meter can be checked by immersing the sensor in
this solution. This solution should not be re-used at
a later date.
Calibration Procedure
1.) Open battery compartment lid on the top of the
meter to access the small white Increment (INC) and
Decrement (DEC) calibration keys. When looking at
the battery compartment with the calibration keys
above the batteries, the DEC key will be to the left.
Probe Calibration
DEC
key INC key

7
2.) If necessary, clean the probe with alcohol to re-
move any residual oils. Rinse the electrode tip in de-
ionized (or distilled) water and then rinse it in the
calibration standard.
3.) Switch unit on with the ON/OFF key. Place
probe tip into a container of calibration standard
(2.76 mS/cm). Take care that the 4 exposed elec-
trodes on the tip are not touching the side or bottom
of the container holding the buffer solution. Wait for
display to stabilize (display value is unchanged and
stable for 3 seconds).
4.) Pressing either calibration key will put the meter
into CALIBRATION mode. Press the INC or DEC
key to adjust the reading. If a key is held down, the
adjustment will happen more rapidly.
5.) When the EC of the calibration standard is
reached, release the keys for 3 seconds. The tem-
perature reading will briefly flash “CO”. The Water-
proof EC Tester accepts the calibration value and
returns to MEASUREMENT mode.
Important - The meter will NOT calibrate to the com-
mon 1414 µS/cm (1.41 mS/cm) conductivity stan-
dard.

8
Meter Configuration
The digital reader for the Field Scout EC meter must
be in Manual, 1-Point calibration mode to allow the
meter to be calibrated with the 2.76 mS/cm calibrat-
ing solution. The meter should also be set to the HI
range mode. This is how the meters are shipped.
Configuring the calibration mode
1. Switch off the display.
2. Press and hold the INC key (see p. 6 for diagram
of calibration keys) then simultaneously press the
ON/OFF button to switch on the display. The meter
will go into calibration selection mode.
3. The lower display shows "A.CAL" and the upper
display blinks the current choice (YES or NO). Press
either the INC or DEC key to select the NO option.
This disables the Automatic calibration mode and
configures the display for Manual calibration.
4. Press the HOLD/ENTER button to confirm the se-
lection. The display shows "CO".
5. After 1 second, the lower display will show "1.Pnt"
and the upper display blinks the current choice (YES
or NO). Press either the INC or DEC key to select
the YES option. This enables the 1-Point calibration
option.
4. Press the HOLD/ENTER button to confirm the se-
lection. The display shows "CO" and, after a few
seconds, goes to measurement mode.

9
Range selection
1. Switch off the display.
2. Press and hold the
o
C/
o
Fkey then press the ON/
OFF button to switch on the display. Release the
o
C/
o
Fkey. The meter will go into Range selection mode
and the lower display will show the current choice.
The options are "AUTO", "PU", "LO", and "HI". See
table 1 for a description of each range.
3. Press the HOLD/ENTER button to select the HI
option. In this mode, the units for EC will always be
in mS/cm. Some users prefer to set the meter on
AUTO range. This gives greater resolution at low
EC's.
Abbreviation EC Range
PU 0 to 200.0 µS/cm
LO 0 to 2000 µS/cm
HI 0 to 20.00 mS/cm
AUTO Automatic
Table 1. Definition of the 4 EC range modes that can be
set on the meter. The mode will be displayed briefly dur-
ing the meter power-up sequence.

10
Greenhouse Soils
The stainless steel probe of the Field Scout Soil &
Water EC Meter can be inserted directly into the soil.
By taking measurements at different soil depths, you
can determine where the fertilizer is concentrated in
the soil. Be aware that the soil moisture content will
significantly influence the measured EC value. To
ensure accurate measurement, it is recommended
that in-situ readings be taken when soil moisture is
close to field capacity or saturation. The probe tip
(sensor) must be held still in the soil to achieve a sta-
ble measurement. Soil EC measurements made
with soils at field capacity or saturation will have
readings 10-15% more than SME measurements
due to a lesser amount of water in the soil.
Soil EC measurements should be made 30-60
minutes after irrigation.
Procedure
- Press On/Off button to power up the meter.
- Insert the probe tip 1 inch below soil surface.
- Wait for reading to stabilize (stable for 3 seconds)
[Automatic Temperature Compensation (ATC)
will correct for temperature changes].
- Repeat at 1 inch increments in the pot.
Golf Course Greens
A similar procedure can be followed for golf course
greens following irrigation or deep-soaking rain
event. Probe to the depth of the turf root zone.
Measurements exceeding 0.7 mS/cm (approximately
equivalent to 2.7 mS/cm in a saturated paste extract)
will result in cool season turf grass stress. See Ap-
pendix 2 (p. 20) for more details.
Direct Soil EC Readings

11
SME Measurement
Saturated Media Extract (SME) Measurements
Growth media used in most greenhouse operations
is high in organic material and processed materials
and low in mineral soil. These materials are easier
to handle, are well aerated and have good moisture-
holding properties, but have limited ability to retain
nutrients. Therefore, tests developed for field soils do
not always yield meaningful results. Saturated Me-
dia Extract (SME) analysis has been shown to elimi-
nate these problems. The samples should not be
dried, sieved or pulverized as this will affect the
growth medium properties and alter the results. Tra-
ditionally, the soil solution from the saturated me-
dium is extracted by a vacuum pump. However, the
Field Scout Soil & Water EC Meter allows the satu-
rated sample to be tested directly.
Procedure
- Moisten the media sample with distilled water to
reach a consistent “saturated” moisture level.
When saturated, the media should glisten and
slide from the mixing spatula with little or no free
water.
- Wait 15 minutes and add more water if needed.
The sample should have the consistency of a
paste with slightly more water than if the media
was in a pot and fully irrigated.
- Press On/Off button to power up the meter.
- Insert the probe tip into the media and read the
results.

12
Liquid measurement/
Other Features
Water (Liquid) Measurements
The Field Scout Soil & Water EC Meter can also
measure the EC of liquids. Simply dip the electrode
tip into the solution and wait for the reading to stabi-
lize (a stable reading occurs when the readout has
not changed for 3 seconds).
Other Features
Hold
Pressing the HOLD key will freeze the display.
Press HOLD again to release.
Temperature Units
Press the C/F key to toggle between displaying tem-
perature in Fahrenheit and Celsius.
Auto Ranging
If the meter’s range mode is set to AUTO (see Meter
Configuration, p. 8), the LCD will automatically tran-
sition from mS/cm to µS/cm as the unit of measure
when the EC value gets smaller (about 2 mS/cm).
They differ by a factor of 1000. For example: 1 mS/
cm = 1000 µS/cm.

13
Maintenance/
Battery Replacement
Changing Batteries:
1.) Open battery compartment lid (located near the
LCD screen).
2.) Remove and replace the old batteries. Note po-
larity shown in battery compartment. When inserting
new batteries, take
care to place them
over the white removal
tab. This will make fu-
ture battery removal
much easier.
3.) Recalibrate meter
after every battery
change.
Maintenance:
To improve performance and avoid transferring soil-
borne diseases, clean the sensor tip by rinsing in al-
cohol for 5 - 10 minutes.
Replace all batteries if low battery indicator appears,
or if readings are faint or unstable.
Store the probe sensor dry.
Important: Do not touch the sensor tip with your
fingers. The oils on the skin will affect the
probe’s measurement accuracy.
batteries
Removal
tab

14
Probe/Tip
Replacement
If the probe cannot be calibrated, or if it does not
hold the calibration for a reasonable amount of time,
the probe or tip must be replaced. Current versions
of the 24” T-handle probe come with a replaceable
tip (item 2266). With these probes, the cable and
shaft do not need to be replaced.
An “OR” reading on the LCD (see Appendix 5) may
indicate a failed probe or simply that the probe has
come unplugged from the meter. See Checking
Probe Connection (p. 16) before replacing the
probe or tip.
Replacing a tip (24” probes only)
The replaceable tip (left) is designed to thread
in and out of the end of the probe. A new tip
has two flat faces on opposite sides. This al-
lows the tip to be tightened onto the probe
with a pliers or 5/16” wrench.
I. Removing a direct-insert probe
The 8” probe and older 24” probes do not have a re-
placeable tip. The replacement procedure is outlined
below.
1. Remove the black nut from the strain-relief
where the cable feeds into the meter.
2. Remove the tan nut on the cable end of the me-
ter.
3. Detach the probe cable plug from the socket in
the meter.
4. Remove the tan nut and large o-ring. For the 24”
probe, also remove the strain relief from the lar-
ger plastic assembly.

15
II. Attaching a direct-insert probe
1. If you are connecting an 8” probe, slide the tan
nut over the probe and down the black cable.
Skip to step 4.
2. If you are connecting a 24” probe, remove the
strain relief from the larger plastic assembly.
3. Feed the cable and strain relief through tan nut
and re-connect the strain relief and the assembly.
4. Attach the probe plug to the socket in the meter
housing.
5. Push the assembly onto the meter housing so the
metal pegs on the assembly line up with the
notches on the inner diameter of the meter open-
ing. Be sure that the small o-ring sits at the base
of the large plastic assembly.
6. While holding the assembly in place hand-tighten
the nut to the strain relief
7. Connect and tighten the tan nut to the meter
housing.
socket
Meter Housing
Probe plug
Larger plastic
assembly/O-ring
Strain relief
Black nut
Tan nut

16
If the meter is giving an out-of-range (OR) error mes-
sage, it may be that the probe has come unplugged
from the meter. The procedure for checking this is
outlined below.
1. Remove the black nut from the strain-relief
where the cable feeds into the meter.
2. Remove the tan nut on the cable end of the me-
ter.
3. Ensure that the probe cable plug is firmly con-
nected to the socket in the meter.
4. Push the assembly onto the meter housing so the
metal pegs on the assembly line up with the
notches on the inner diameter of the meter open-
ing. Be sure that the small o-ring sits at the base
of the large plastic assembly.
5. While holding the assembly in place hand-tighten
the nut to the strain relief
6. Connect and tighten the tan nut to the meter
housing.
Checking Probe
Connection
Probe plug
Larger plastic
assembly/O-ring
Strain relief
black nut
tan nut

17
Readout LCD digital display
EC Range 0.00 - 19.99 mS/cm
Temperature 0 - 55
o
C (32 - 122
o
F)
Range
Accuracy EC: ±1% Full Scale
Temperature: ±0.5
o
C
EC Resolution 0.01 mS/cm
Calibration 1-point with 2.76 mS/cm
standard
Temperature Automatic from 0 to 50
o
C
Compensation
Power Four LR44 1.5V alkaline
batteries
Battery Life 150 hours
Auto Shutoff After 8.5 minutes
Specifications

18
Plant EC (mS/cm)
Asparagus 1.5 - 2.0
Watermelon 1.5 - 2.5
Carrot 1.5 - 2.0
Cabbage 2.0 - 3.0
Cucumber 2.0 - 3.0
Crysanthemum 1.5 - 2.5
Onion 1.5 - 2.0
Bean 2.0 - 2.5
Strawberry 2.0 - 2.5
Lettuce 1.0 - 1.5
Eggplant 2.5 - 3.0
Melon 1.5 - 2.5
Potato 2.0 - 3.0
Pepper 2.0 - 3.0
Pea 1.0 - 1.5
Tomato 2.5 - 5.0
Celery 2.0 - 2.5
Marrow 2.0 - 2.5
Recommended soil EC for selected vegetable crops.
Note: The values on this table refer to measurement
of a saturated media extract (SME). See Appendix
3 for information on converting from direct-insert
readings to SME.
Appendix 1
Preferred EC Values
for Selected Plants

19
Recommended EC Value (mS/cm)
SME
a
1 to 2
b
Pour thru
Poinsettia during
weeks 2-12. 2.0 - 3.0 0.85 - 1.25 2.8 - 4.1
Pansies during
active growth. 0.25 - 1.5 0.1 - 0.6 0.35 - 2.1
Geraniumus during
active growth. 1.6 - 2.4 0.65 - 1.0 2.2 - 3.3
Comparison of substrate tests for various EC sam-
pling methods. (Calvins, Whipker, and Fonteno,
North Carolina State University).
a
saturated media extract
b
1 part soil to 2 parts water

20
Appendix 2
nterpreting EC Readings
From Turf Grass
When taking direct-insert EC readings in turf grass
with the Field Scout meter, it is often helpful to con-
vert the measurement to the equivalent Saturated
Media Extract (SME) value. This conversion will
vary for different soils. For sandy soils, the expres-
sion: SME = 2.7FC + 0.8
provides a good approximation. FC refers to the
reading taken by the Field Scout meter. This equa-
tion is the basis for table 1. Table 2 lists a variety of
grass species and the range of EC values (converted
to SME) they can tolerate.
FS SME FS SME FS SME
0.1 1.1 1.1 3.8 2.1 6.5
0.2 1.3 1.2 4.0 2.2 6.7
0.3 1.6 1.3 4.3 2.3 7.0
0.4 1.9 1.4 4.6 2.4 7.3
0.5 2.2 1.5 4.9 2.5 7.6
0.6 2.4 1.6 5.1 2.6 7.8
0.7 2.7 1.7 5.4 2.7 8.1
0.8 3.0 1.8 5.7 2.8 8.4
0.9 3.2 1.9 5.9 2.9 8.6
1.0 3.5 2.0 6.2 3.0 8.9
Table 1: Conversion from Field Scout direct readings
(FS) to equivalent Saturated Media Extract (SME)
values. (Reference 9:3. PACE Turfgrass Research
Institute. San Diego, CA)