METREL A 1501 User manual

Flex current clamps
A 1501, A 1502 and A 1503
Instruction Manual
Version 1.1.1; Code No. 20 752 759

2
Distributor:
Producer:
METREL d.d.
Ljubljanska 77
SI-1354 Horjul
Tel.: [phone]
Fax: [phone]
E-mail: me[email protected]
http://www.metrel.si
Mark on your equipment certifies that it meets European Union requirements
for EMC, LVD, ROHS regulations
© 2017 Metrel
No part of this publication may be reproduced or utilized in any form or by any means
without permission in writing from METREL.

Flex current clamps A 1501, A 1502 and A 1503
3
Table of contents
1Introduction ............................................................................................................. 4
2Main features .......................................................................................................... 4
3Safety...................................................................................................................... 5
4Symbols .................................................................................................................. 5
5Typical applications................................................................................................. 6
5.1 Power Quality Measurement ............................................................................. 6
5.2 Energy and Power Measurement ...................................................................... 6
6Connecting and using clamps in the field................................................................. 6
6.1 Effective current measuring range..................................................................... 8
7Technical specifications........................................................................................... 9
7.1 A 1501 and A 1502............................................................................................ 9
7.1.1 Range 30A - Typical Characteristics.......................................................... 10
7.2 A 1503............................................................................................................. 11
7.2.1 Range 60A - Typical Characteristics.......................................................... 12
8Cleaning................................................................................................................ 13
9Service.................................................................................................................. 13

Flex current clamps A 1501, A 1502 and A 1503
4
1 Introduction
Flexible Current Clamps A 1501, A 1502 and A 1503 are based on Rogowski coil
principle and can measure alternating currents on low and medium power installations.
Unlike standard current transformers, this type of current sensor does not use magnetic
cores. The transformation principle is based on an air core. It presents virtually no load
to the system under test, has a low phase shift and excellent frequency response.
They consist of current sensor of different lengths and active electronic for multiple
current range, as shown on table below. User should select sensor length according to
the current conductor diameter where measurements will be performed.
Model
Flexible
sensor
length
Maximal
conductor
diameter
Nominal
current range
Effective
measurement range
A 1501
25 cm / 10 in
7 cm / 2,7 in
30 A
300 A
3000A
3 A … 45 A
15 A … 450 A
80 A … 4500 A
A 1502
48 cm / 19 in
14 cm / 5,5 in
A 1503
90 cm / 35 in
27 cm / 10,6 in
60 A
600 A
6000A
6 A …90 A
30 A …900 A
160 A …9000 A
Embedded electronic module provides automatic clamp recognition (for Metrel
instruments) and current range switching. Module is powered directly from attached
instrument, so clamp does not require additional power supply. The flexible sensor
permits measurements on conductors where standard clamp-on current transformers
cannot be used. It is particularly useful for installation in tight spaces, or around breaker
panels, cable bundles, wide or large bus bars and irregular shapes.
Additionally, clamps can’t be damaged by overloads; they are insensitive to DC current,
and measure only the AC component of the current.
2 Main features
Range setup from the instrument, no additional range setup needed
Power supply for electronic module is assured from the instrument
Waterproof sensor
Minimum angle shift to accomplish accurate power measurements
High accuracy
Total rejection of DC component
Friendly-use of the closing-opening system of the current sensor (even if wearing
gloves) due to its highly ergonomic design
Very light, flexible and fully adaptable to busbar trunking system and insulated
cables
Strengthened security, regardless the working environment industrial or services

Flex current clamps A 1501, A 1502 and A 1503
5
3 Safety
Read the operating instructions before use and follow all safety instructions.
If the test equipment is used in a manner that is not specified in this user manual,
the protection provided by the equipment might be impaired!
Adhere to local and national safety codes. Individual protective equipment must
be used to prevent shock and arc blast injury where hazardous live conductors
are exposed.
Before each use, inspect the Current Clamps and its latching system for any
damage. Pay particular attention to the insulation surrounding the flexible
measuring head. Look for cracks or missing portions of the clamp housing or
output cable insulation. Also look for loose or weakened components.
Do not use a clamp that is cracked, damaged, or has a defective cable.
Never use the clamp on a circuit with voltages higher than 1000 V CAT III or
600 V CAT IV.
De-energize the installation on which current will be measured or adopt safe
operating procedures during application and removal of the current clamp.
Use extreme caution when working around bare conductors or bus bars.
Do not use the Current Clamp to measure bare conductors carrying a voltage
from 30 V up to 1000 V unless you are wearing protective clothing suitable for
high-voltage work. Contact with the conductor could result in electric shock.
Always use appropriate equipment for personal protection.
Use caution when working with voltages above 60 V dc, 30 V ac rms or 42 V ac
peak. Such voltages pose a shock hazard.
4 Symbols
Symbol
Description
Important information. Refer to the manual.
Risk of Electric Shock.
Product is protected by Double/Reinforced insulation
Do not apply around or remove from HAZARDUS LIVE conductors.
Do not dispose of this product as unsorted municipal waste. Contact
Metrel or a qualified recycler for disposal.
Complies with the relevant European standards.

Flex current clamps A 1501, A 1502 and A 1503
6
5 Typical applications
5.1 Power Quality Measurement
Current clamps have linear response through wide frequency bandwidth (see Figure 7 and
Figure 11). Therefore they are well suited for:
Power Quality auditing,
EN 50160 or troubleshooting. Particularly for:
Current distortion measurement
Inrush measurement
Functional testing of appliances, machines, etc.
High precision (see Figure 5 and Figure 9) and wide measurement range can cover most of
practical LV current measurements.
5.2 Energy and Power Measurement
Current clamps have small phase shift (see Figure 8 and Figure 12) over wide frequency range.
Therefore they are well suited for:
Power and energy measurements (active, reactive, apparent)
Power factor measurements
Power/Energy efficiency
6 Connecting and using clamps in the field
1. Wrap the flexible measuring head around the conductor to be tested and close
coupling
Figure 1: Flex clamps connection

Flex current clamps A 1501, A 1502 and A 1503
7
It is very important that the conductor is in the centre and perpendicular to the
current censor as much as possible, in order to minimise position
measurement error.
Minimise influence of adjacent current-carrying conductors, and measure at
the point where they are far away from each other.
Make sure that the arrow marked on the clamp coupling points toward the
correct orientation for correct phase.
Keep the clamp coupling more than 2.5 cm (1 in) away from conductor.
2. Connect Flexible Current Clamps to the desired input on the measuring instrument
Figure 2: 3-phase 4-wire system
3. Select Phase and Neutral clamps to Smart Clamp in Connection setup menu on
your instrument.
4. Select appropriate Current clamp range.
5. Observe the current value and waveform on the instrument’s display. If desired,
select the lower range on the measurement instrument.

Flex current clamps A 1501, A 1502 and A 1503
8
6.1 Effective current measuring range
Technical specification of current clamp present many different errors which are
influenced by various parameters (position, temperature). Most of them can be
minimised in controlled laboratory use. However in the field ideal measurement
condition can hardly be met. Therefore we recommend selecting clamp measuring
range according to the Effective measurement range, shown in table below.
Effective measurement range is range where measurement error is less than 5 % of
measured value (reading), and includes all relevant errors (residual noise, clamp
accuracy, position sensitivity and instrument accuracy).
Effective measuring range
3A 30A300A 3000A 30000A
3000A range Error > 5% Pure sin
wave
Effective measuring range Pure sin
wave
15A600A
Effective measuring range Puresin
wave60A
300A range
30A range
6000A
Error > 5%
80A
Error > 5%
1A
45A
450A
4500A
Figure 3: A 1501 and A 1502 effective measuring range (error is <5% of m.v.)
Effective measuring range
6A 60A600A 6000A 60000A
6000A range Error > 5% Pure sin
wave
Effective measuring range Pure sin
wave
30A1200A
Effective measuring range Puresin
wave120A
600A range
60A range
12kA
Error > 5%
160A
Error > 5%
1A
90A
900A
9000A
Figure 4: A 1503 effective measuring range (error is <5% of m.v.)

Flex current clamps A 1501, A 1502 and A 1503
9
7 Technical specifications
7.1 A 1501 and A 1502
FEATURES
DESCRIPTION
NOTES
Length of the sensor
A 1501 –25 cm / 10 in
A 1502 –48 cm / 25 in
Max. conductor diameter
A 1501 –7 cm / 2,7 in
A 1502 –14 cm / 5,5 in
Nominal current range
30 A / 300 A / 3000 A ac rms,
with current crest factor 3
Effective measuring range
30A range: 3 A …45 A
300A range: 15 A …450 A
3000A range: 80 A …4500 A
3,5
Maximal current
60 A / 600 A / 6000 A of pure sinus current
Bandwidth
10 Hz …8 kHz
1
Accuracy
±1.2 % of reading
2,3
Position sensitivity
±1 % of nominal current range
Temperature dependency
+/-0.01 % of reading / ºC
Residual current (noise)
30A range: 0.12 A
300A range: 0.3 A
3000A range: 3 A
3
Phase error
<0.2°@ 50 Hz
<3°@1.5 kHz
External magnetic field
rejection in reference to
adjacent conductor
Min. 40 dB ( < 1% of adjacent conductor current)
4
Electrical Safety
Double insulation
EN 61010 –CAT III / 1000 V up to 3000 m
Pollution degree
2
Working and storage
temperature range:
Flexible current sensor: -20 …85 ºC
Other clamp parts: -20 …70 ºC
Humidity
95 % RH (0 C …40 C), non-condensing
Weight of flexible sensor
A 1501 –< 150 g
A 1502 –< 170 g
Water and dust proofing
IP 65
1. Limits of bandwidth corresponding to a relative gain > - 3 dB
2. Reference conditions:
Frequency 50/60 Hz;
conductor is in the centre and perpendicular to the current clamps;
temperature 23 ºC;
Clamps connected to MI 2892 Power Master;
Laboratory environment.
3.   󰇡
 󰇢
 
4. Adjacent conductor ≥ 20 cm from current clamps.
5. With accuracy: ±5 % of reading from the MI 2892 Power Master in real
conditions (with position, residual current, and intrinsic errors included)

Flex current clamps A 1501, A 1502 and A 1503
10
7.1.1 Range 30A - Typical Characteristics
Figure 5: RMS Accuracy (50 Hz)
Figure 6: Phase error (50 Hz)
Figure 7: Frequency Accuracy (30Arms)
Figure 8: Phase error (30Arms)
0,00
0,20
0,40
0,60
0,80
1,00
1,20
1,40
0,1 1 10
Accuracy (% of m.v.)
RMS Current (A)
0,00
0,02
0,04
0,06
0,08
0,10
0,12
0,10 1,00 10,00
Phase error (degrees)
RMS Current [A]
-3,00
-2,50
-2,00
-1,50
-1,00
-0,50
0,00
0,50
20 200 2000
Accuracy (% of m.v.)
Frequency (Hz)
0
5
10
15
20
25
30
35
10 100 1000
Phase error (degrees)
Frequency (Hz)

Flex current clamps A 1501, A 1502 and A 1503
11
7.2 A 1503
FEATURES
DESCRIPTION
NOTES
Length of the sensor
90 cm / 35 in
Max. conductor diameter
27 cm / 10,6 in
Nominal current range
60 A / 600 A / 6000 A ac rms, with crest factor
3 or less
Effective measuring range
60A range: 6 A …90 A
600A range: 30 A …900 A
6000A range: 160 A …9000 A
3,5
Maximal current
120 A / 1200 A / 12000 A of pure sinus current
Bandwidth
10 Hz …8 kHz
1
Accuracy
±1.2 % of reading
2, 3
Position sensitivity
±2 % of nominal current range
Temperature dependency
± 0.02 % of reading / ºC
5
External magnetic field
rejection in reference to
adjacent conductor
40 dB ( 1 % of adjacent conductor current)
4
Residual current (noise)
60A range: 0.24 A
600A range: 0.6 A
6000A range: 6 A
3
Phase error
<0.2°@ 50 Hz
<3°@ 1.5 kHz
Electrical Safety
Double insulation
EN 61010 –CAT III / 1000 V up to 3000 m
Pollution degree
2
Working and storage
temperature range:
Flexible current sensor: -20 …85 ºC
Other clamp parts: -20 …70 ºC
Humidity
95 % RH (0 C …40 C), non-condensing
Weight of flexible sensor
< 200 g
Water and dust proofing
IP 65
1. Limits of bandwidth corresponding to a relative gain > - 3 dB
2. Reference conditions:
Frequency: 50/60 Hz;
Temperature: 23 ºC;
Conductor is in the centre and perpendicular to the current clamps;
Clamps connected to MI 2892 Power Master;
Laboratory environment.
3.   󰇡
 󰇢
 
4. Adjacent conductor ≥ 10 cm from current clamps.
5. With accuracy: ±5 % of reading from the MI 2892 Power Master in real
conditions (with position, residual current, and intrinsic errors included)

Flex current clamps A 1501, A 1502 and A 1503
12
7.2.1 Range 60A - Typical Characteristics
Figure 9: RMS Accuracy (50 Hz)
Figure 10: Phase error (50 Hz)
Figure 11: RMS Accuracy (60A)
Figure 12: Phase error (60 A)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
050 100 150
Accuracy (% of m.v.)
RMS Current (A)
0,00
0,02
0,04
0,06
0,08
0,10
0,12
0,10 1,00 10,00 100,00
Phase error (degrees)
RMS Current (A)
0,00
0,10
0,20
0,30
0,40
0,50
0,60
0,70
0,80
0 1000 2000 3000
Accuracy (% of m.v.)
Frequency (Hz)
0
5
10
15
20
25
30
35
10 100 1000
Phase error (degrees)
Frequency (Hz)

Flex current clamps A 1501, A 1502 and A 1503
13
8 Cleaning
Use soft patch, slightly moistened with soap water or alcohol, to clean the surface of the
clamps and leave it to dry totally, before using it.
Do not use liquids based on petrol or hydrocarbons!
Do not spill cleaning liquid over the device!
9 Service
For repairs under or out of warranty time please contact your Metrel distributor for
further information.
Name and address of manufacturer:
METREL d.d.
Ljubljanska cesta 77
SI-1354 Horjul
Tel.: [phone], fax.: [phone]
http://www.metrel.si
E-mail: me[email protected]