Spinner II 25 User manual

0.9 gpm at 60 psig
Model 25 250 cc Dirt Capacity
Installation Instructions
Parts List
Service Instructions
Bulletin 71951

Oil Supply to Centrifuge
Oil supply should, in general, be taken from
the highest pressure, hottest source available
immediately downstream of the lube pump.
A3⁄8” pipe (or #6 hose) supply line should be
used. The unit’s supply port is a #6 female
SAE O-ring design (9⁄16-18 straight thread).
Preferred pressure is 60 to 80 psig but the
Spinner II centrifuge will operate efficiently
at 35 to 90 psig. The idle Cut-Out Valve (COV)
allows oil to enter the unit only when supply
pressure exceeds 20 psi.
Clean Oil Return to Sump
Gravity Drain. The Spinner II centrifuge
must be close-coupled to the sump with an
unrestricted 1” ID (or #20 hose) drain returning
above the normal sump oil level. The drain
line must be sloped downward from the
centrifuge outlet and be free of sharp bends
or traps. On many engines, an access plate
into the gear train or crankcase can be modified
to provide a suitable drain opening as well as
sturdy mechanical support. Be sure the sump
side of the drain opening is clear and that the
drain oil does not impinge on moving parts of
the engine.
Mechanical Considerations
Spinner II centrifuges are high–speed devices
and should be securely mounted to prevent
excessive vibration. Operation up to 10 or 15
degrees from vertical is permitted. Further
installation guidelines are provided in Spinner II
diagram A1-4154.
Model 25 Installation Instructions
FLOW
5500
5000
4500
4000
3500
3000
Oil Flow U.S. gpm
SPEED
10 20 30 40 50 60 70 80 90
Oil Pressure – psig
0.2
0.4
0.6
0.8
1.0
1.2
6000
6500
7000
SAE30 Oil at 167°F / 75°C
Turbine Speed rpm
4 Fixing holes
Ø 9
50
220
61 61 9
153
20
50
Ø 90
Ø 120
Ø 109
Oil outlet
Oil inlet
All dimensions in millimeters
Cut-out
valve
Minimum height
for rotor removal
Ø 40

Model 25 Parts List
Description Part number
Only items shown with part numbers are available.
Bold denotes assembly
Centrifuge, Spinner II/Model 25 with COV (Cut-Out Valve) .... 71957
Cover assembly .................................................................................. 71080
Nut-cover .............................................................................................. 71081
■Seal-cover nut ..................................................................................... 71082
Ring, retaining-cover nut .................................................................. 71083
Centrifuge turbine assembly .......................................................... 71085
Nut-centrifuge bowl ............................................................................ 71086
Bowl-centrifuge ................................................................................... 71087
●Seal-centrifuge turbine, nitrile ......................................................... 71089
Standtube-centrifuge ......................................................................... 71088
●Turbine body ........................................................................................ 71952
Nozzle-turbine (2 required) ....................................................part of 71085
Base assembly with spindle ........................................................... 71979
●Seal-base to cover (nitrile) ................................................................ 71084
■Kit cut-out valve ................................................................................. 71950
Gasket-base ......................................................................................... 71091
Service Cycle ●Whenever bowl is cleaned or replaced.
■At unit rebuild or when required.
Rev 9/02

1. Shut off oil supply (or stop engine) and allow
centrifuge turbine assembly to come to a
complete stop.
2. Unscrew cover nut and remove cover
assembly.
3. Partially withdraw centrifuge turbine assem-
bly from the housing and allow oil to drain
from nozzles before removing completely.
Hold the assembly in one hand and remove
bowl nut. Carefully separate centrifuge bowl
from turbine. Remove stand tube.
4. Carefully remove sludge from centrifuge
bowl using a wooden spatula or other non-
damaging tool.
5. Wipe out bowl with solvent and wash stand
tube and other parts.
6. Clean turbine and examine top and bottom
bearings for excessive wear. Check turbine
nozzles to ensure free passage of oil. Replace
centrifuge bowl seal.
7. Seat stand tube in turbine, replace bowl and
reassemble centrifuge, tightening the bowl
nut securely by hand and making sure that
the bowl seal is uniformly seated all around.
18. Examine spindle journals for damage or
excessive wear. Replace base assembly if
journals are damaged. Spindle is pressed
into base and aligned at the factory and
cannot be properly serviced in the field.
19. Replace centrifuge turbine assembly on
spindle, being careful of bushings. Be sure
it rotates freely.
10. Clean and inspect cover, paying special
attention to cover-nut assembly. The seal
should be replaced if it shows signs of
leaking.
11. Examine the base-to-cover seal and replace
if damaged.
12. Replace cover assembly and tighten cover
nut securely to 8 ft-lbs maximum. Make sure
that cover seats on base assembly evenly
all around so that cover seal is properly
compressed. Check all centrifuge mounting
bolts for proper tightness.
13. Open oil supply to centrifuge. With engine
running, check all connections and joints
for leaks. Repeat assembly if vibration is
excessive.
Tel: [phone] or 800-231-7746
Fax: [phone]
Mail: P.O. Box 920946
Houston, Texas USA 77292-0946
Warehouse: 4405 Directors Row
Houston, Texas USA 77092
Web Site: www.Spinnerii.com
Made in England by Mann+Hummel (UK) Ltd. Patented worldwide.
®Spinner II is a registered trademark of T.F. Hudgins, Incorporated.
©2002 T.F. Hudgins, Incorporated. All rights reserved.
Litho in U.S.A. Bulletin 71951/9-02
Sales and Service
Model 25 SE Service Instructions